← Commit history

Set visibility: public

Ray ·d977834ce9 · ·parent e2974d7
1 file changed +10−7
page.json+10−7
@@ -32,7 +32,7 @@         "number": "1",         "name": "BOOT",         "type": "passive",-        "description": "Power supply bias for the high-side power MOSFET gate driver. Connect a 0.1\u00b5F bootstrap capacitor from BOOT to SW. Capacitor is charged when the low-side power MOSFET is on or SW voltage is low. Absolute max 46V; BOOT-SW max 6V; BOOT-SW UVLO threshold ~2.36V."+        "description": "Power supply bias for the high-side power MOSFET gate driver. Connect a 0.1µF bootstrap capacitor from BOOT to SW. Capacitor is charged when the low-side power MOSFET is on or SW voltage is low. Absolute max 46V; BOOT-SW max 6V; BOOT-SW UVLO threshold ~2.36V."       },       {         "number": "2",@@ -44,25 +44,25 @@         "number": "3",         "name": "EN",         "type": "input",-        "description": "Enable pin to the regulator with internal pull-up current source (1.5\u00b5A at 1V, 5.5\u00b5A at 1.5V). Pull below 1.1V to disable the converter; float or connect to VIN to enable. Enable rising threshold ~1.18V. Tap of a VIN-to-GND resistor divider on EN can set the input UVLO threshold. Absolute max 42V."+        "description": "Enable pin to the regulator with internal pull-up current source (1.5µA at 1V, 5.5µA at 1.5V). Pull below 1.1V to disable the converter; float or connect to VIN to enable. Enable rising threshold ~1.18V. Tap of a VIN-to-GND resistor divider on EN can set the input UVLO threshold. Absolute max 42V."       },       {         "number": "4",         "name": "RT/CLK",         "type": "bidirectional",-        "description": "Sets internal oscillator switching frequency or accepts an external synchronization clock. Connect a resistor from this pin to GND to program frequency between 300kHz and 2.2MHz (RT[k\u03a9] = 100000 / fsw[kHz]); or drive with an external clock (high >2V, low <0.4V, pulse >80ns) and the internal PLL will lock. Must not be left floating or shorted to GND. Absolute max 6V."+        "description": "Sets internal oscillator switching frequency or accepts an external synchronization clock. Connect a resistor from this pin to GND to program frequency between 300kHz and 2.2MHz (RT[kΩ] = 100000 / fsw[kHz]); or drive with an external clock (high >2V, low <0.4V, pulse >80ns) and the internal PLL will lock. Must not be left floating or shorted to GND. Absolute max 6V."       },       {         "number": "5",         "name": "FB",         "type": "input",-        "description": "Inverting input of the trans-conductance error amplifier. Connect to the tap of the output-to-GND feedback resistor divider that programs the output voltage. Device regulates FB to the internal 0.8V (\u00b11%) reference. Overvoltage protection trips at ~110% of VREF. Absolute max 6V."+        "description": "Inverting input of the trans-conductance error amplifier. Connect to the tap of the output-to-GND feedback resistor divider that programs the output voltage. Device regulates FB to the internal 0.8V (±1%) reference. Overvoltage protection trips at ~110% of VREF. Absolute max 6V."       },       {         "number": "6",         "name": "SS",         "type": "passive",-        "description": "Soft-start programming pin. Connect a ceramic capacitor from SS to GND to set soft-start time; an internal 3\u00b5A current source pulls SS toward VCC. Css = tss * 3\u00b5A / 0.8V; programmed soft-start time should be greater than 4ms. Absolute max 6V."+        "description": "Soft-start programming pin. Connect a ceramic capacitor from SS to GND to set soft-start time; an internal 3µA current source pulls SS toward VCC. Css = tss * 3µA / 0.8V; programmed soft-start time should be greater than 4ms. Absolute max 6V."       },       {         "number": "7",@@ -80,7 +80,7 @@         "number": "9",         "name": "Thermal Pad",         "type": "power_in",-        "description": "Exposed thermal pad on the die back - heat dissipation path. Must be electrically connected to the GND pin and soldered to the PCB ground plane for proper operation and optimized thermal performance (R\u03b8JA \u2248 42\u00b0C/W)."+        "description": "Exposed thermal pad on the die back - heat dissipation path. Must be electrically connected to the GND pin and soldered to the PCB ground plane for proper operation and optimized thermal performance (RθJA ≈ 42°C/W)."       }     ],     "provenance": {@@ -144,5 +144,8 @@     "docs/sct2432ster-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ]+  ],+  "visibility": {+    "public": true+  } }\ No newline at end of file