SC1169
Public Made by Adomby adom
Raspberry Pi RF and Wireless, 21-SMD Module. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
70b0c7c
SC1169
Raspberry Pi · RF and Wireless · 21-SMD Module
SC1169 from Raspberry Pi, in a 21-SMD Module. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 2 | NC | unconnected | No connect; Table 2 lists no default connection for this pin. |
| 3 | gSPI SCLK | input | gSPI serial clock from the host microcontroller, default connection GPIO29. |
| 4 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 5 | gSPI DATA IN | input | gSPI data input to the CYW43439 from the host, default connection GPIO24, which must be the same GPIO pin as pins 6 and 10. |
| 6 | gSPI DATA OUT | output | gSPI data output from the CYW43439 to the host, default connection GPIO24 through a 470 Ω resistor. |
| 7 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 8 | GPIO0 | bidirectional | General-purpose GPIO0 of the CYW43439, readable and controllable from the host only when the chip is powered and communication is active. |
| 9 | gSPI CS | input | gSPI chip select from the host, default connection GPIO25. |
| 10 | nIRQ | output | Interrupt from the CYW43439 to the host indicating work is pending, default connection GPIO24 through a 10 kΩ resistor. |
| 11 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 12 | Wi-Fi on | input | Wi-Fi enable (regulator on) used by the host to power up the CYW43 radio, default connection GPIO23, shared with pin 13. |
| 13 | Bluetooth on | input | Bluetooth enable signal from the host, default connection GPIO23, shared with pin 12. |
| 14 | VDDIO | power_in | I/O supply that sets the interface voltage, which must be either 1.8 V ±5% or 3.3 V ±5% (default 3.3 V). |
| 15 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 16 | Vin | power_in | Main supply input that must be between 3.0 V and 4.8 V; a Vin below 3.2 V reduces RF performance (default 3.3 V). |
| 17 | GPIO2 | bidirectional | General-purpose GPIO2 of the CYW43439, available for host-controlled general-purpose I/O. |
| 18 | GPIO1 | bidirectional | General-purpose GPIO1 of the CYW43439, available for host-controlled general-purpose I/O. |
| 19 | NC | unconnected | No connect; Table 2 lists no default connection for this pin. |
| 20 | NC | unconnected | No connect; Table 2 lists no default connection for this pin. |
| 21 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Raspberry Pi |
| Package | 21-SMD Module |
| Category | RF and Wireless |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage Vin (pin 16) | Vin | 3 | 4.8 | V | 12 | ||
| Input high voltage (3.3 V ±5% I/O) | VIH | 2 | V | VDDIO = 3.3 V ±5% I/O | 12 | ||
| Input low voltage (3.3 V ±5% I/O) | VIL | 0.8 | V | VDDIO = 3.3 V ±5% I/O | 12 | ||
| Output low voltage (1.8 V ±5% I/O) | VOL | 0.45 | V | VDDIO = 1.8 V ±5% I/O; at 2 mA | 12 | ||
| Output low voltage (3.3 V ±5% I/O) | VOL | 0.4 | V | VDDIO = 3.3 V ±5% I/O; at 2 mA | 12 | ||
| I/O supply tolerance at 1.8 V setting | VDDIO | -5 | 5 | % | 1.8 V I/O setting | 12 | |
| I/O supply tolerance at 3.3 V setting | VDDIO | -5 | 5 | % | 3.3 V I/O setting | 12 | |
| ESD human body model contact discharge | ESD_HAND_HBM | 1000 | V | Human body model contact discharge per JEDEC EID/JESD22-A114 | 12 | ||
| ESD machine model contact discharge | ESD_HAND_HM | 30 | V | Machine model contact | 12 | ||
| ESD charged device model contact discharge | ESD_HAND_CDM | 300 | V | Charged device model contact discharge per JEDEC EIA/JESD22-C101 | 12 | ||
| Ambient operating temperature | -30 | 70 | °C | Functionality guaranteed; specifications require de-rating at extreme temperatures | 13 | ||
| Storage temperature | -40 | 125 | °C | 13 | |||
| Relative operating humidity | 85 | % | Less than 85% | 13 | |||
| Relative storage humidity | 60 | % | Less than 60% | 13 | |||
| Peak package body temperature (reflow) | Tp | 260 | °C | Peak package body temperature during reflow | 14 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | gold | of RM2, including a 21-pin castellated package consisting of 1.5 mm pitch gold contacts. These castellations are plated half-holes that allow for secure soldering onto another PCB, enabling an RM2 to | 8 |
CAD (Adom-generated)
- Symbol:
SC1169 - Footprint:
Adom_Gen:Raspberry_Pi_SC1169_7e8aee - 3D model: generated to fit the land (STEP)
- 3D model files:
sc1169-etched.step/sc1169-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sc1169.step/sc1169.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Raspberry Pi datasheet (17 pp, sha256
0f611d884ce6cbc3, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.
# SC1169
**Raspberry Pi** · RF and Wireless · 21-SMD Module
SC1169 from Raspberry Pi, in a 21-SMD Module. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 2 | NC | unconnected | No connect; Table 2 lists no default connection for this pin. |
| 3 | gSPI SCLK | input | gSPI serial clock from the host microcontroller, default connection GPIO29. |
| 4 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 5 | gSPI DATA IN | input | gSPI data input to the CYW43439 from the host, default connection GPIO24, which must be the same GPIO pin as pins 6 and 10. |
| 6 | gSPI DATA OUT | output | gSPI data output from the CYW43439 to the host, default connection GPIO24 through a 470 Ω resistor. |
| 7 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 8 | GPIO0 | bidirectional | General-purpose GPIO0 of the CYW43439, readable and controllable from the host only when the chip is powered and communication is active. |
| 9 | gSPI CS | input | gSPI chip select from the host, default connection GPIO25. |
| 10 | nIRQ | output | Interrupt from the CYW43439 to the host indicating work is pending, default connection GPIO24 through a 10 kΩ resistor. |
| 11 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 12 | Wi-Fi on | input | Wi-Fi enable (regulator on) used by the host to power up the CYW43 radio, default connection GPIO23, shared with pin 13. |
| 13 | Bluetooth on | input | Bluetooth enable signal from the host, default connection GPIO23, shared with pin 12. |
| 14 | VDDIO | power_in | I/O supply that sets the interface voltage, which must be either 1.8 V ±5% or 3.3 V ±5% (default 3.3 V). |
| 15 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
| 16 | Vin | power_in | Main supply input that must be between 3.0 V and 4.8 V; a Vin below 3.2 V reduces RF performance (default 3.3 V). |
| 17 | GPIO2 | bidirectional | General-purpose GPIO2 of the CYW43439, available for host-controlled general-purpose I/O. |
| 18 | GPIO1 | bidirectional | General-purpose GPIO1 of the CYW43439, available for host-controlled general-purpose I/O. |
| 19 | NC | unconnected | No connect; Table 2 lists no default connection for this pin. |
| 20 | NC | unconnected | No connect; Table 2 lists no default connection for this pin. |
| 21 | GND | power_in | Ground connection that must be tied to the host system ground, since RM2 needs a good ground plane for optimal RF performance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Raspberry Pi |
| Package | 21-SMD Module |
| Category | RF and Wireless |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage Vin (pin 16) | Vin | 3 | | 4.8 | V | | 12 |
| Input high voltage (3.3 V ±5% I/O) | VIH | 2 | | | V | VDDIO = 3.3 V ±5% I/O | 12 |
| Input low voltage (3.3 V ±5% I/O) | VIL | | | 0.8 | V | VDDIO = 3.3 V ±5% I/O | 12 |
| Output low voltage (1.8 V ±5% I/O) | VOL | | | 0.45 | V | VDDIO = 1.8 V ±5% I/O; at 2 mA | 12 |
| Output low voltage (3.3 V ±5% I/O) | VOL | | | 0.4 | V | VDDIO = 3.3 V ±5% I/O; at 2 mA | 12 |
| I/O supply tolerance at 1.8 V setting | VDDIO | -5 | | 5 | % | 1.8 V I/O setting | 12 |
| I/O supply tolerance at 3.3 V setting | VDDIO | -5 | | 5 | % | 3.3 V I/O setting | 12 |
| ESD human body model contact discharge | ESD_HAND_HBM | | | 1000 | V | Human body model contact discharge per JEDEC EID/JESD22-A114 | 12 |
| ESD machine model contact discharge | ESD_HAND_HM | | | 30 | V | Machine model contact | 12 |
| ESD charged device model contact discharge | ESD_HAND_CDM | | | 300 | V | Charged device model contact discharge per JEDEC EIA/JESD22-C101 | 12 |
| Ambient operating temperature | | -30 | | 70 | °C | Functionality guaranteed; specifications require de-rating at extreme temperatures | 13 |
| Storage temperature | | -40 | | 125 | °C | | 13 |
| Relative operating humidity | | | | 85 | % | Less than 85% | 13 |
| Relative storage humidity | | | | 60 | % | Less than 60% | 13 |
| Peak package body temperature (reflow) | Tp | | | 260 | °C | Peak package body temperature during reflow | 14 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | gold | of RM2, including a 21-pin castellated package consisting of 1.5 mm pitch gold contacts. These castellations are plated half-holes that allow for secure soldering onto another PCB, enabling an RM2 to | 8 |
## CAD (Adom-generated)
- Symbol: `SC1169`
- Footprint: `Adom_Gen:Raspberry_Pi_SC1169_7e8aee`
- 3D model: generated to fit the land (STEP)
- 3D model files: `sc1169-etched.step` / `sc1169-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sc1169.step` / `sc1169.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Raspberry Pi datasheet](https://datasheets.raspberrypi.com/rm2/rm2-datasheet.pdf) (17 pp, sha256 `0f611d884ce6cbc3`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.
[Datasheet PDF](docs/sc1169-datasheet.pdf)