Diodes SBR10U45SP5-13 — 45 V PowerDI5 rectifier

{
 "plan": {
  "schema": "adom/mark-plan@1",
  "mpn": "SBR10U45SP5-13",
  "step": "/home/adom/project/adom-custom-electronic-load/references/sbr10u45sp5/SBR10U45SP5-nominal.step",
  "footprint": "/home/adom/project/adom-custom-electronic-load/references/powerdi5/D_PowerDI-5.kicad_mod",
  "standUp": [],
  "standUpSource": "as-is (Z up)",
  "face": "top",
  "pin1": {
   "source": "footprint pad 1",
   "xyMm": [
    -1.12,
    -0.0
   ],
   "corner": "left/middle"
  },
  "existingMarks": [],
  "vendorMarking": {
   "present": false,
   "glyphFaces": 0
  },
  "faceNormal": [
   0,
   0,
   1
  ],
  "longAxis": {
   "axis": "x",
   "vector": [
    1.0,
    0.0,
    0.0
   ],
   "why": "two-terminal part: along the body, pad 1 to pad 2 (between the terminations)",
   "override": null
  },
  "readingDirection": {
   "vector": [
    1.0,
    0.0,
    0.0
   ],
   "angleDeg": 0,
   "textUp": [
    -0.0,
    1.0,
    0.0
   ],
   "rule": "pin 1 / pad 1 at the start (left) of the text, and below it when it sits on a side"
  },
  "band": {
   "regionMm": [
    -2.685,
    -1.983,
    2.685,
    1.983
   ],
   "zMm": 1.1,
   "lengthMm": 5.37,
   "heightMm": 3.966,
   "why": "highest flat face over the body centre",
   "terminationsExcludedBy": null,
   "trimmedEnds": [],
   "keepouts": [],
   "sideTurn": null,
   "margins": {
    "lengthEachSide": 0.12,
    "heightEachSide": 0.15
   }
  },
  "text": {
   "lines": [
    "SBR10U",
    "45SP5-13"
   ],
   "chars": 14,
   "capHeightMm": 0.6397,
   "smallestLineMm": 0.6397,
   "heightPctOfBand": 37.1,
   "why": "two lines: the smaller line (0.640 mm) beats one line (0.361 mm) by 1.77x",
   "alternative": {
    "lines": [
     "SBR10U45SP5-13"
    ],
    "capHeightMm": 0.3612,
    "smallestLineMm": 0.3612
   },
   "font": "service-step2glb /laser-etch (single-stroke outline font)"
  },
  "etch": {
   "poseQuarterTurnsZ": 0,
   "service": "/laser-etch?mode=flat",
   "note": "turn so the reading direction is +X, etch, fit the mark into the band, turn back"
  },
  "outline": {
   "upAxis": "z",
   "poseRotZDeg": 180,
   "rot": 180,
   "recipe": "adom-aiflow-etch outline <part.step> --footprint <part.kicad_mod> --mpn SBR10U45SP5-13 (stands the STEP up (as-is (Z up)), turns it 180 deg about Z and draws SBR10U / 45SP5-13 on the planned band, rot 180)",
   "why": "iso camera looks from +X+Y+Z: text along +Y (rot 90) or -X (rot 180) reads left to right with pin 1 toward the viewer"
  },
  "widget": {
   "px": 320,
   "pxPerMm": 43.1,
   "capHeightPx": 22.5
  },
  "hints": [],
  "warnings": [],
  "summary": "Mark along the 5.37 mm axis (+X), 0.64 mm text (2 lines), upright with pin 1 left middle, outline rot 180 after a 180 deg pose turn; ~23 px caps at 320 px"
 },
 "etch": {
  "out": "/home/adom/project/adom-custom-electronic-load/references/sbr10u45sp5/SBR10U45SP5-marked.step",
  "mpn": "SBR10U45SP5-13",
  "lines": [
   "SBR10U",
   "45SP5-13"
  ],
  "removedOldMarks": [],
  "turns": [],
  "serviceMarkTurnedQuarter": 0,
  "line2Scaled": true,
  "fit": {
   "scale": 0.6562,
   "capMm": 0.6383,
   "markMm": [
    4.0812,
    1.4966
   ],
   "bandMm": [
    5.37,
    3.966
   ],
   "zMm": 1.105
  }
 }
}