main
Ray
Publish 0.1.0
9c660cc
S25FS064SAGMFI010
Infineon/Cypress Semicon · NOR FLASH · SOIC-8
S25FS064SAGMFI010 from Infineon/Cypress Semicon, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select: when HIGH the device is deselected, ignores all inputs except RESET#/IO3_RESET#, outputs are high impedance and it is in Standby; driving LOW enables the device. |
| 2 | SO / IO1 | bidirectional | Serial Output for single bit data commands, and IO1 for Dual or Quad commands. |
| 3 | WP# / IO2 | bidirectional | Write Protect when not in Quad mode (CR1V[1]=0 and SR1NV[7]=1) and IO2 in Quad mode (CR1V[1]=1); has an internal pull-up and may be left unconnected if not used. |
| 4 | VSS | power_in | Ground: common voltage drain and ground reference for the device core, input receivers and output drivers. |
| 5 | SI / IO0 | bidirectional | Serial Input for single bit data commands, and IO0 for Dual or Quad commands; values are latched on the rising edge of SCK. |
| 6 | SCK | input | Serial Clock: inputs are latched on the rising edge, and SDR output data changes after the falling edge (DDR after every edge). |
| 7 | IO3 / RESET# | bidirectional | IO3 in Quad mode when CS# is LOW, or hardware RESET# when enabled by CR2V[5]=1 and not in Quad mode or CS# is HIGH; has an internal pull-up and may be left unconnected if not used. |
| 8 | VCC | power_in | Power supply for all device internal logic and functions including read, program and erase, 1.7 V to 2.0 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon/Cypress Semicon |
| Package | SOIC-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input LOW voltage | VIL | -0.5 | V | 131 | |||
| Output LOW voltage | VOL | 0.2 | V | IOL = 0.1 mA | 131 | ||
| Input leakage current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VSS, CS# = VIH | 131 | |
| Output leakage current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VSS, CS# = VIH | 131 | |
| Active power supply current (READ), serial SDR | ICC1 | 10 | 18 | mA | Serial SDR@50 MHz | 131 | |
| Active power supply current (READ), serial SDR | ICC1 | 25 | 30 | mA | Serial SDR@133 MHz | 131 | |
| Active power supply current (READ), QIO/QPI SDR | ICC1 | 60 | 65 | mA | QIO/QPI SDR@133 MHz | 131 | |
| Active power supply current (READ), QIO/QPI DDR | ICC1 | 70 | 90 | mA | QIO/QPI DDR@80 MHz | 131 | |
| Active power supply current (page program) | ICC2 | 60 | 100 | mA | CS# = VCC | 131 | |
| Active power supply current (WRR or WRAR) | ICC3 | 60 | 100 | mA | CS# = VCC | 131 | |
| Active power supply current (SE) | ICC4 | 60 | 100 | mA | CS# = VCC | 131 | |
| Active power supply current (BE) | ICC5 | 60 | 100 | mA | CS# = VCC | 131 | |
| Standby current | ISB | 25 | 100 | µA | IO3/RESET#, CS# = VCC; SI, SCK = VCC or VSS, Industrial Temp | 131 | |
| Deep power down current | IDPD | 6 | 50 | µA | IO3/RESET#, CS# = VCC; SI, SCK = VCC or VSS, Industrial Temp | 131 | |
| Power on reset current | IPOR | 80 | mA | IO3/RESET#, CS# = VCC; SI, SCK = VCC or VSS | 131 | ||
| Storage temperature plastic packages | -65 | 150 | °C | 128 | |||
| Ambient temperature with power applied | -65 | 125 | °C | 128 | |||
| VCC supply voltage (absolute maximum) | VCC | -0.5 | 2.5 | V | 128 | ||
| Input voltage with respect to ground (VSS) | -0.5 | V | Printed maximum is VCC + 0.5 V (expression, not numeric) | 128 | |||
| Output short circuit current | 100 | mA | No more than one output shorted to ground at a time; duration not greater than one second | 128 | |||
| Latchup: input voltage on all input-only connections | -1 | V | VCC = 1.8 V, one connection at a time tested; printed maximum is VCC + 1.0 V (expression) | 128 | |||
| Latchup: input voltage on all I/O connections | -1 | V | VCC = 1.8 V, one connection at a time tested; printed maximum is VCC + 1.0 V (expression) | 128 | |||
| Latchup: VCC current | -100 | 100 | mA | VCC = 1.8 V, one connection at a time tested; excludes power supply VCC | 128 | ||
| Junction to ambient thermal resistance | Theta JA | 54 | °C/W | SOC008 (SOIC 8-lead) package | 128 | ||
| Junction to board thermal resistance | Theta JB | 38 | °C/W | SOC008 (SOIC 8-lead) package | 128 | ||
| Junction to case thermal resistance | Theta JC | 31 | °C/W | SOC008 (SOIC 8-lead) package | 128 | ||
| VCC power supply voltage (operating) | VCC | 1.7 | 2 | V | 128 | ||
| VCC (cut-off) where re-initialization is needed | VCC (cut-off) | 1.55 | V | 130 | |||
| VCC (LOW) voltage for initialization to occur | VCC (LOW) | 0.7 | V | 130 | |||
| VCC (LOW) time | tPD | 10 | µs | 130 | |||
| Ambient temperature, Industrial (I) | TA | -40 | 85 | °C | Industrial (I) grade | 129 | |
| Reset setup (prior reset end and RESET# HIGH before RESET# LOW) | tRS | 50 | ns | 33 | |||
| Reset pulse hold (RESET# LOW to CS# LOW) | tRPH | 35 | µs | 33 | |||
| RESET# pulse width | tRP | 200 | ns | 34 | |||
| Reset hold (RESET# HIGH before CS# LOW) | tRH | 50 | ns | 34 | |||
| SCK clock frequency for READ and 4READ instructions | FSCK, R | 50 | MHz | READ and 4READ instructions | 35 | ||
| SCK clock frequency for dual and quad commands | FSCK, C | 133 | MHz | DOR, 4DOR, DIOR, 4DIOR, QOR, 4QOR, QIOR, 4QIOR | 35 | ||
| CS# HIGH time (read instructions) | tCS | 10 | ns | Read instructions | 35 | ||
| CS# active setup time (relative to SCK) | tCSS | 2 | ns | 35 | |||
| CS# active hold time (relative to SCK) | tCSH | 3 | ns | 35 | |||
| Data in setup time | tSU | 2 | ns | 35 | |||
| Data in hold time | tHD | 3 | ns | 35 | |||
| Clock LOW to output valid | tV | 8 | ns | Full VCC range and CL = 30 pF | 35 | ||
| Clock LOW to output valid (SOIC package) | tV | 6.5 | ns | Full VCC range and CL = 15 pF; SOIC package | 35 | ||
| Output disable time | tDIS | 8 | ns | 35 | |||
| WP# setup time | tWPS | 20 | ns | Only applicable as constraint for WRR or WRAR when SRWD is set to 1 | 35 | ||
| WP# hold time | tWPH | 100 | ns | Only applicable as constraint for WRR or WRAR when SRWD is set to 1 | 35 | ||
| CS# HIGH to power-down mode | tDPD | 3 | µs | 35 | |||
| CS# HIGH to standby mode without electronic signature read | tRES | 30 | µs | 35 | |||
| SCK clock frequency for DDR READ instruction | FSCK, R | 80 | MHz | DDR READ instruction | 38 | ||
| CS# HIGH time (Read instructions) | tCS | 10 | ns | Read instructions | 38 | ||
| CS# active setup time (Relative to SCK) | tCSS | 2 | ns | 38 | |||
| CS# active hold time (Relative to SCK) | tCSH | 3 | ns | 38 | |||
| IO in setup time | tSU | 1.5 | ns | 38 | |||
| IO in hold time | tHD | 1.5 | ns | 38 | |||
| Clock LOW to output valid (DDR) | tV | 1.5 | 6 | ns | CL = 15 pF | 38 | |
| First IO to last IO data valid time | tIO_skew | 700 | ps | SOIC package; not tested | 38 | ||
| Output disable time (DDR) | tDIS | 8 | ns | 38 | |||
| Input capacitance (SCK, CS#, IO3/RESET#) | CIN | 12.5 | pF | 1 MHz, SOIC | 32 | ||
| Output capacitance (all I/O) | COUT | 12 | pF | 1 MHz, SOIC | 32 |
CAD (KiCad official)
- Symbol:
S25FS064SAGMFI010 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
s25fs064sagmfi010-etched.step/s25fs064sagmfi010-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fs064sagmfi010.step/s25fs064sagmfi010.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Infineon/Cypress Semicon datasheet (172 pp, sha256
f2e0ff9948688c22, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# S25FS064SAGMFI010
**Infineon/Cypress Semicon** · NOR FLASH · SOIC-8
S25FS064SAGMFI010 from Infineon/Cypress Semicon, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS# | input | Chip Select: when HIGH the device is deselected, ignores all inputs except RESET#/IO3_RESET#, outputs are high impedance and it is in Standby; driving LOW enables the device. |
| 2 | SO / IO1 | bidirectional | Serial Output for single bit data commands, and IO1 for Dual or Quad commands. |
| 3 | WP# / IO2 | bidirectional | Write Protect when not in Quad mode (CR1V[1]=0 and SR1NV[7]=1) and IO2 in Quad mode (CR1V[1]=1); has an internal pull-up and may be left unconnected if not used. |
| 4 | VSS | power_in | Ground: common voltage drain and ground reference for the device core, input receivers and output drivers. |
| 5 | SI / IO0 | bidirectional | Serial Input for single bit data commands, and IO0 for Dual or Quad commands; values are latched on the rising edge of SCK. |
| 6 | SCK | input | Serial Clock: inputs are latched on the rising edge, and SDR output data changes after the falling edge (DDR after every edge). |
| 7 | IO3 / RESET# | bidirectional | IO3 in Quad mode when CS# is LOW, or hardware RESET# when enabled by CR2V[5]=1 and not in Quad mode or CS# is HIGH; has an internal pull-up and may be left unconnected if not used. |
| 8 | VCC | power_in | Power supply for all device internal logic and functions including read, program and erase, 1.7 V to 2.0 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon/Cypress Semicon |
| Package | SOIC-8 |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input LOW voltage | VIL | -0.5 | | | V | | 131 |
| Output LOW voltage | VOL | | | 0.2 | V | IOL = 0.1 mA | 131 |
| Input leakage current | ILI | -2 | | 2 | µA | VCC = VCC Max, VIN = VIH or VSS, CS# = VIH | 131 |
| Output leakage current | ILO | -2 | | 2 | µA | VCC = VCC Max, VIN = VIH or VSS, CS# = VIH | 131 |
| Active power supply current (READ), serial SDR | ICC1 | | 10 | 18 | mA | Serial SDR@50 MHz | 131 |
| Active power supply current (READ), serial SDR | ICC1 | | 25 | 30 | mA | Serial SDR@133 MHz | 131 |
| Active power supply current (READ), QIO/QPI SDR | ICC1 | | 60 | 65 | mA | QIO/QPI SDR@133 MHz | 131 |
| Active power supply current (READ), QIO/QPI DDR | ICC1 | | 70 | 90 | mA | QIO/QPI DDR@80 MHz | 131 |
| Active power supply current (page program) | ICC2 | | 60 | 100 | mA | CS# = VCC | 131 |
| Active power supply current (WRR or WRAR) | ICC3 | | 60 | 100 | mA | CS# = VCC | 131 |
| Active power supply current (SE) | ICC4 | | 60 | 100 | mA | CS# = VCC | 131 |
| Active power supply current (BE) | ICC5 | | 60 | 100 | mA | CS# = VCC | 131 |
| Standby current | ISB | | 25 | 100 | µA | IO3/RESET#, CS# = VCC; SI, SCK = VCC or VSS, Industrial Temp | 131 |
| Deep power down current | IDPD | | 6 | 50 | µA | IO3/RESET#, CS# = VCC; SI, SCK = VCC or VSS, Industrial Temp | 131 |
| Power on reset current | IPOR | | | 80 | mA | IO3/RESET#, CS# = VCC; SI, SCK = VCC or VSS | 131 |
| Storage temperature plastic packages | | -65 | | 150 | °C | | 128 |
| Ambient temperature with power applied | | -65 | | 125 | °C | | 128 |
| VCC supply voltage (absolute maximum) | VCC | -0.5 | | 2.5 | V | | 128 |
| Input voltage with respect to ground (VSS) | | -0.5 | | | V | Printed maximum is VCC + 0.5 V (expression, not numeric) | 128 |
| Output short circuit current | | | | 100 | mA | No more than one output shorted to ground at a time; duration not greater than one second | 128 |
| Latchup: input voltage on all input-only connections | | -1 | | | V | VCC = 1.8 V, one connection at a time tested; printed maximum is VCC + 1.0 V (expression) | 128 |
| Latchup: input voltage on all I/O connections | | -1 | | | V | VCC = 1.8 V, one connection at a time tested; printed maximum is VCC + 1.0 V (expression) | 128 |
| Latchup: VCC current | | -100 | | 100 | mA | VCC = 1.8 V, one connection at a time tested; excludes power supply VCC | 128 |
| Junction to ambient thermal resistance | Theta JA | | | 54 | °C/W | SOC008 (SOIC 8-lead) package | 128 |
| Junction to board thermal resistance | Theta JB | | | 38 | °C/W | SOC008 (SOIC 8-lead) package | 128 |
| Junction to case thermal resistance | Theta JC | | | 31 | °C/W | SOC008 (SOIC 8-lead) package | 128 |
| VCC power supply voltage (operating) | VCC | 1.7 | | 2 | V | | 128 |
| VCC (cut-off) where re-initialization is needed | VCC (cut-off) | 1.55 | | | V | | 130 |
| VCC (LOW) voltage for initialization to occur | VCC (LOW) | 0.7 | | | V | | 130 |
| VCC (LOW) time | tPD | 10 | | | µs | | 130 |
| Ambient temperature, Industrial (I) | TA | -40 | | 85 | °C | Industrial (I) grade | 129 |
| Reset setup (prior reset end and RESET# HIGH before RESET# LOW) | tRS | 50 | | | ns | | 33 |
| Reset pulse hold (RESET# LOW to CS# LOW) | tRPH | 35 | | | µs | | 33 |
| RESET# pulse width | tRP | 200 | | | ns | | 34 |
| Reset hold (RESET# HIGH before CS# LOW) | tRH | 50 | | | ns | | 34 |
| SCK clock frequency for READ and 4READ instructions | FSCK, R | | | 50 | MHz | READ and 4READ instructions | 35 |
| SCK clock frequency for dual and quad commands | FSCK, C | | | 133 | MHz | DOR, 4DOR, DIOR, 4DIOR, QOR, 4QOR, QIOR, 4QIOR | 35 |
| CS# HIGH time (read instructions) | tCS | 10 | | | ns | Read instructions | 35 |
| CS# active setup time (relative to SCK) | tCSS | 2 | | | ns | | 35 |
| CS# active hold time (relative to SCK) | tCSH | 3 | | | ns | | 35 |
| Data in setup time | tSU | 2 | | | ns | | 35 |
| Data in hold time | tHD | 3 | | | ns | | 35 |
| Clock LOW to output valid | tV | | | 8 | ns | Full VCC range and CL = 30 pF | 35 |
| Clock LOW to output valid (SOIC package) | tV | | | 6.5 | ns | Full VCC range and CL = 15 pF; SOIC package | 35 |
| Output disable time | tDIS | | | 8 | ns | | 35 |
| WP# setup time | tWPS | 20 | | | ns | Only applicable as constraint for WRR or WRAR when SRWD is set to 1 | 35 |
| WP# hold time | tWPH | 100 | | | ns | Only applicable as constraint for WRR or WRAR when SRWD is set to 1 | 35 |
| CS# HIGH to power-down mode | tDPD | | | 3 | µs | | 35 |
| CS# HIGH to standby mode without electronic signature read | tRES | | | 30 | µs | | 35 |
| SCK clock frequency for DDR READ instruction | FSCK, R | | | 80 | MHz | DDR READ instruction | 38 |
| CS# HIGH time (Read instructions) | tCS | 10 | | | ns | Read instructions | 38 |
| CS# active setup time (Relative to SCK) | tCSS | 2 | | | ns | | 38 |
| CS# active hold time (Relative to SCK) | tCSH | 3 | | | ns | | 38 |
| IO in setup time | tSU | 1.5 | | | ns | | 38 |
| IO in hold time | tHD | 1.5 | | | ns | | 38 |
| Clock LOW to output valid (DDR) | tV | 1.5 | | 6 | ns | CL = 15 pF | 38 |
| First IO to last IO data valid time | tIO_skew | | | 700 | ps | SOIC package; not tested | 38 |
| Output disable time (DDR) | tDIS | | | 8 | ns | | 38 |
| Input capacitance (SCK, CS#, IO3/RESET#) | CIN | | | 12.5 | pF | 1 MHz, SOIC | 32 |
| Output capacitance (all I/O) | COUT | | | 12 | pF | 1 MHz, SOIC | 32 |
## CAD (KiCad official)
- Symbol: `S25FS064SAGMFI010`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files: `s25fs064sagmfi010-etched.step` / `s25fs064sagmfi010-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `s25fs064sagmfi010.step` / `s25fs064sagmfi010.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Infineon/Cypress Semicon datasheet](docs/s25fs064sagmfi010-datasheet.pdf) (172 pp, sha256 `f2e0ff9948688c22`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/s25fs064sagmfi010-datasheet.pdf)