Generated by kicad-footprint-generator · KiCad file format 20260206
S25FL512SAGMFAR10
Cypress Semicon · NOR FLASH · SOIC-16
S25FL512SAGMFAR10 from Cypress Semicon, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | HOLD#/IO3 | bidirectional | HOLD# input pauses a command while low when Quad mode is off (CR[1]=0), and the pin acts as I/O3 when Quad mode is enabled. |
| 2 | VCC | power_in | Core voltage supply for all internal logic, including read, program and erase, with a range of 2.7 V to 3.6 V. |
| 3 | RESET# | input | Hardware reset input, bonded out on the R1 model; driving it low for tRP starts the hardware reset process. |
| 4 | DNU | unconnected | Do not use; the pin has an internal pull-down resistor, may be left unconnected or tied to VSS, and no host signal may be connected to it. |
| 5 | DNU | unconnected | Do not use; the pin has an internal pull-down resistor, may be left unconnected or tied to VSS, and no host signal may be connected to it. |
| 6 | RFU | unconnected | Reserved for future use; no internal signal is currently connected, and it should not be used for PCB routing channels. |
| 7 | CS# | input | Chip select input; the SPI interface is in standby when CS# is high, and a command begins when CS# goes low. |
| 8 | SO/IO1 | bidirectional | Serial data output in single mode, and I/O1 in dual and quad modes. |
| 9 | WP#/IO2 | bidirectional | Write protect input, relevant only during the instruction cycles of a WRR command, and I/O2 in Quad mode. |
| 10 | VSS | power_in | Common ground reference for the device core, input signal receivers and output drivers. |
| 11 | DNU | unconnected | Do not use; the pin has an internal pull-down resistor, may be left unconnected or tied to VSS, and no host signal may be connected to it. |
| 12 | DNU | unconnected | Do not use; the pin has an internal pull-down resistor, may be left unconnected or tied to VSS, and no host signal may be connected to it. |
| 13 | NC | unconnected | Not connected internally; any signal routed through it must not exceed VIO. |
| 14 | VIO | power_in | Versatile I/O supply for all input receivers and output drivers, with a range of 1.65 V to VCC that must not exceed VCC. |
| 15 | SI/IO0 | bidirectional | Serial data input in single mode, and I/O0 in dual and quad modes. |
| 16 | SCK | input | Serial clock input for the SPI interface, supporting SPI clock modes 0 and 3. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Cypress Semicon |
| Package | SOIC-16 |
| Category | Memory |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Short Circuit Current | 100 | mA | No more than one output shorted to ground; duration not greater than 1 s | 30 | |||
| VCC supply voltage (absolute maximum) | VCC | -0.5 | 4 | V | 30 | ||
| VIO supply voltage (absolute maximum) | VIO | -0.5 | 4 | V | 30 | ||
| Storage Temperature | -65 | 150 | °C | Plastic packages | 30 | ||
| Ambient Temperature with Power Applied | -65 | 125 | °C | 30 | |||
| Core supply voltage VCC | VCC | 2.7 | 3.6 | V | 30 | ||
| I/O supply voltage VIO | VIO | 1.65 | V | VIO must be at or below VCC + 200 mV | 30 | ||
| Ambient Temperature TA | TA | -40 | 85 | °C | Automotive, AEC-Q100 Grade 3 (A) | 31 | |
| Input Leakage Current | ILI | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 34 | |
| Output Leakage Current | ILO | -2 | 2 | µA | VCC = VCC Max, VIN = VIH or VIL | 34 | |
| Active Power Supply Current (READ) Serial SDR@50 MHz | ICC1 | 16 | mA | Serial SDR@50 MHz; outputs unconnected during read data return | 34 | ||
| Active Power Supply Current (READ) Serial SDR@133 MHz | ICC1 | 33 | mA | Serial SDR@133 MHz, Industrial temperature range; outputs unconnected during read data return | 34 | ||
| Active Power Supply Current (READ) Quad SDR @80 MHz | ICC1 | 50 | mA | Quad SDR @80 MHz; outputs unconnected during read data return | 34 | ||
| Active Power Supply Current (READ) Quad SDR @104 MHz | ICC1 | 61 | mA | Quad SDR @104 MHz; outputs unconnected during read data return | 34 | ||
| Active Power Supply Current (READ) Quad DDR @66 MHz | ICC1 | 75 | mA | Quad DDR @66 MHz; outputs unconnected during read data return | 34 | ||
| Active Power Supply Current (READ) Quad DDR @80 MHz | ICC1 | 90 | mA | Quad DDR @80 MHz; outputs unconnected during read data return | 34 | ||
| Active Power Supply Current (Page Program) | ICC2 | 100 | mA | CS# = VIO | 34 | ||
| Active Power Supply Current (WRR) | ICC3 | 100 | mA | CS# = VIO | 34 | ||
| Active Power Supply Current (SE) | ICC4 | 100 | mA | CS# = VIO | 34 | ||
| Active Power Supply Current (BE) | ICC5 | 100 | mA | CS# = VIO | 34 | ||
| Standby Current (Industrial) | ISB | 70 | 100 | µA | RESET#, CS# = VIO; SI, SCK = VIO or VSS, Industrial Temp | 34 | |
| SCK Clock Frequency for READ and 4READ instructions | FSCK, R | 50 | MHz | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| SCK Clock Frequency for single commands | FSCK, C | 133 | MHz | Single commands as shown in Table 40; VIO = VCC 2.7 V to 3.6 V | 40 | ||
| SCK Clock Frequency for dual and quad commands | FSCK, C | 104 | MHz | DOR, 4DOR, QOR, 4QOR, DIOR, 4DIOR, QIOR, 4QIOR; VIO = VCC 2.7 V to 3.6 V | 40 | ||
| SCK Clock Frequency for QPP commands | FSCK, QPP | 80 | MHz | QPP, 4QPP commands; VIO = VCC 2.7 V to 3.6 V | 40 | ||
| CS# High Time (Read Instructions) | tCS | 10 | ns | Read instructions; VIO = VCC 2.7 V to 3.6 V | 40 | ||
| CS# High Time (Program/Erase) | tCS | 50 | ns | Program/Erase; VIO = VCC 2.7 V to 3.6 V | 40 | ||
| CS# Active Setup Time (relative to SCK) | tCSS | 3 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| CS# Active Hold Time (relative to SCK) | tCSH | 3 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| Data in Setup Time | tSU | 1.5 | 3000 | ns | Max applies only during Program/Erase Suspend/Resume; VIO = VCC 2.7 V to 3.6 V | 40 | |
| Data in Hold Time | tHD | 2 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| Clock Low to Output Valid (full VCC range) | tV | 8 | ns | Full VCC range (2.7-3.6 V) and CL = 30 pF | 40 | ||
| Clock Low to Output Valid (regulated VCC) | tV | 7.65 | ns | Regulated VCC range (3.0-3.6 V) and CL = 30 pF | 40 | ||
| Clock Low to Output Valid (regulated VCC, CL 15 pF) | tV | 6.5 | ns | Regulated VCC range (3.0-3.6 V) and CL = 15 pF | 40 | ||
| Output Hold Time | tHO | 2 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| Output Disable Time | tDIS | 0 | 8 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | |
| WP# Setup Time | tWPS | 20 | ns | Only applicable as constraint for WRR when SRWD is set to 1 | 40 | ||
| WP# Hold Time | tWPH | 100 | ns | Only applicable as constraint for WRR when SRWD is set to 1 | 40 | ||
| HOLD# Active Setup Time (relative to SCK) | tHLCH | 3 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| HOLD# Active Hold Time (relative to SCK) | tCHHH | 3 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| HOLD# Non Active Setup Time (relative to SCK) | tHHCH | 3 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| HOLD# Non Active Hold Time (relative to SCK) | tCHHL | 3 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| HOLD# enable to Output Invalid | tHZ | 8 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| HOLD# disable to Output Valid | tLZ | 8 | ns | VIO = VCC 2.7 V to 3.6 V | 40 | ||
| Theta JA Thermal resistance (junction to ambient) | Theta JA | 29.6 | °C/W | SL3016 package; still air (0 m/s), EIA/JESD51 | 30 | ||
| Theta JB Thermal resistance (junction to board) | Theta JB | 7.9 | °C/W | SL3016 package | 30 | ||
| Theta JC Thermal resistance (junction to case) | Theta JC | 8.8 | °C/W | SL3016 package | 30 |
CAD (KiCad official)
- Symbol:
S25FL512SAGMFAR10 - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
s25fl512sagmfar10-etched.step/s25fl512sagmfar10-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);s25fl512sagmfar10.step/s25fl512sagmfar10.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Cypress Semicon datasheet (161 pp, sha256
3485e138d6aed187, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).