← Commit history

Initial commit: component/s2-lpqtr

Ray ·17281911ce ·
2 files changed +304
README.mdadded+61
@@ -0,0 +1,61 @@+# S2-LPQTR++**STMicroelectronics** · RF Transceiver ICs · QFN-24-EP(4x4)++S2-LPQTR from STMicroelectronics, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VDD_SMPS | power_in | Analog power supply input for SMPS block, accepts 1.8 V to 3.6 V. |+| 2 | SMPS1 | power_out | SMPS step-down converter output ranging from 1.1 V to 1.8 V, requires external LC filtering. |+| 3 | SMPS2 | power_in | SMPS regulated voltage input after LC filtering, accepts 1.1 V to 1.8 V from SMPS1. |+| 4 | XOUT | output | Crystal oscillator output terminal, leave floating when driving XIN with external clock source. |+| 5 | XIN | input | Crystal oscillator input or external clock source accepting 0.2 V DC minimum with 400 mVpp AC amplitude, maximum instantaneous voltage 1.4 V. |+| 6 | SDN | input | Shutdown input pin, must be held low in all operating modes, high voltage enters shutdown. |+| 7 | VDD_ANA_SYNTH | power_in | Analog and synthesizer circuit power supply, accepts 1.8 V to 3.6 V. |+| 8 | VR_SYNTH | power_out | Synthesizer LDO output at 1.2 V for external decoupling capacitor. |+| 9 | VREF_VCO | power_out | VCO LDO band-gap reference voltage at 1.2 V for external decoupling capacitor. |+| 10 | VDD_VCO_TX | power_in | VCO and transmitter power supply, accepts 1.8 V to 3.6 V. |+| 11 | TX | output | RF output from power amplifier with programmable output power from -30 dBm to +16 dBm. |+| 12 | VR_RF | power_out | RX low-dropout regulator output at 1.2 V for external decoupling capacitor. |+| 13 | RXn | input | Differential RF input negative terminal for dual-ended low-noise amplifier. |+| 14 | RXp | input | Differential RF input positive terminal for dual-ended low-noise amplifier. |+| 15 | VDD_RX_DIG | power_in | Receiver and digital circuit power supply, accepts 1.8 V to 3.6 V. |+| 16 | SDO | tri_state | SPI slave data output (MISO), tri-state high-impedance when chip select is high. |+| 17 | SDI | input | SPI slave data input (MOSI) from master microcontroller. |+| 18 | SCLK | input | SPI slave clock input, supports up to 10 MHz clock frequency. |+| 19 | CSn | input | SPI chip select active-low input for bus contention control. |+| 20 | GPIO0 | bidirectional | General-purpose I/O, configurable as digital input or output through SPI registers. |+| 21 | GPIO1 | bidirectional | General-purpose I/O, configurable as digital input or output through SPI registers. |+| 22 | GPIO2 | bidirectional | General-purpose I/O, configurable as digital input or output through SPI registers. |+| 23 | GPIO3 | bidirectional | General-purpose I/O, configurable as digital input or output through SPI registers. |+| 24 | VR_DIG | power_out | Digital circuit LDO output at 1.2 V for external decoupling capacitor. |+| 25 | GND | power_in | Device ground reference and exposed thermal pad for heat dissipation. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | QFN-24-EP(4x4) |+| Category | RF And Wireless |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `S2-LPQTR`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`+- 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `s2-lpqtr-etched.step` / `s2-lpqtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `s2-lpqtr.step` / `s2-lpqtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8565342028100886528) (90 pp, sha256 `d405f18ec87fd3ad`, retrieved 2026-09-23, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/s2-lpqtr-datasheet.pdf)
page.jsonadded+243
@@ -0,0 +1,243 @@+{+  "slug": "s2-lpqtr",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics RF Transceiver ICs, QFN-24-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "rf and wireless",+    "s2-lpqtr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "s2-lpqtr.kicad_sym",+    "s2-lpqtr.kicad_mod",+    "s2-lpqtr.glb",+    "s2-lpqtr.step",+    "s2-lpqtr.lbr",+    "docs/hero.png",+    "docs/s2-lpqtr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "S2-LPQTR",+    "manufacturer": "STMicroelectronics",+    "package": "QFN-24-EP(4x4)",+    "pin_count": 25,+    "category": "RF And Wireless",+    "subcategory": "RF Transceiver ICs",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8565342028100886528",+    "parts": {+      "symbol": "s2-lpqtr.kicad_sym",+      "footprint": "s2-lpqtr.kicad_mod",+      "model_3d": "s2-lpqtr-etched.glb",+      "model_3d_plain": "s2-lpqtr.glb",+      "model_3d_step": "s2-lpqtr-etched.step",+      "model_3d_step_plain": "s2-lpqtr.step",+      "lbr": "s2-lpqtr.lbr"+    },+    "distributor_links": {+      "lcsc": "C880591"+    },+    "pins": [+      {+        "number": "1",+        "name": "VDD_SMPS",+        "type": "power_in",+        "description": "Analog power supply input for SMPS block, accepts 1.8 V to 3.6 V."+      },+      {+        "number": "2",+        "name": "SMPS1",+        "type": "power_out",+        "description": "SMPS step-down converter output ranging from 1.1 V to 1.8 V, requires external LC filtering."+      },+      {+        "number": "3",+        "name": "SMPS2",+        "type": "power_in",+        "description": "SMPS regulated voltage input after LC filtering, accepts 1.1 V to 1.8 V from SMPS1."+      },+      {+        "number": "4",+        "name": "XOUT",+        "type": "output",+        "description": "Crystal oscillator output terminal, leave floating when driving XIN with external clock source."+      },+      {+        "number": "5",+        "name": "XIN",+        "type": "input",+        "description": "Crystal oscillator input or external clock source accepting 0.2 V DC minimum with 400 mVpp AC amplitude, maximum instantaneous voltage 1.4 V."+      },+      {+        "number": "6",+        "name": "SDN",+        "type": "input",+        "description": "Shutdown input pin, must be held low in all operating modes, high voltage enters shutdown."+      },+      {+        "number": "7",+        "name": "VDD_ANA_SYNTH",+        "type": "power_in",+        "description": "Analog and synthesizer circuit power supply, accepts 1.8 V to 3.6 V."+      },+      {+        "number": "8",+        "name": "VR_SYNTH",+        "type": "power_out",+        "description": "Synthesizer LDO output at 1.2 V for external decoupling capacitor."+      },+      {+        "number": "9",+        "name": "VREF_VCO",+        "type": "power_out",+        "description": "VCO LDO band-gap reference voltage at 1.2 V for external decoupling capacitor."+      },+      {+        "number": "10",+        "name": "VDD_VCO_TX",+        "type": "power_in",+        "description": "VCO and transmitter power supply, accepts 1.8 V to 3.6 V."+      },+      {+        "number": "11",+        "name": "TX",+        "type": "output",+        "description": "RF output from power amplifier with programmable output power from -30 dBm to +16 dBm."+      },+      {+        "number": "12",+        "name": "VR_RF",+        "type": "power_out",+        "description": "RX low-dropout regulator output at 1.2 V for external decoupling capacitor."+      },+      {+        "number": "13",+        "name": "RXn",+        "type": "input",+        "description": "Differential RF input negative terminal for dual-ended low-noise amplifier."+      },+      {+        "number": "14",+        "name": "RXp",+        "type": "input",+        "description": "Differential RF input positive terminal for dual-ended low-noise amplifier."+      },+      {+        "number": "15",+        "name": "VDD_RX_DIG",+        "type": "power_in",+        "description": "Receiver and digital circuit power supply, accepts 1.8 V to 3.6 V."+      },+      {+        "number": "16",+        "name": "SDO",+        "type": "tri_state",+        "description": "SPI slave data output (MISO), tri-state high-impedance when chip select is high."+      },+      {+        "number": "17",+        "name": "SDI",+        "type": "input",+        "description": "SPI slave data input (MOSI) from master microcontroller."+      },+      {+        "number": "18",+        "name": "SCLK",+        "type": "input",+        "description": "SPI slave clock input, supports up to 10 MHz clock frequency."+      },+      {+        "number": "19",+        "name": "CSn",+        "type": "input",+        "description": "SPI chip select active-low input for bus contention control."+      },+      {+        "number": "20",+        "name": "GPIO0",+        "type": "bidirectional",+        "description": "General-purpose I/O, configurable as digital input or output through SPI registers."+      },+      {+        "number": "21",+        "name": "GPIO1",+        "type": "bidirectional",+        "description": "General-purpose I/O, configurable as digital input or output through SPI registers."+      },+      {+        "number": "22",+        "name": "GPIO2",+        "type": "bidirectional",+        "description": "General-purpose I/O, configurable as digital input or output through SPI registers."+      },+      {+        "number": "23",+        "name": "GPIO3",+        "type": "bidirectional",+        "description": "General-purpose I/O, configurable as digital input or output through SPI registers."+      },+      {+        "number": "24",+        "name": "VR_DIG",+        "type": "power_out",+        "description": "Digital circuit LDO output at 1.2 V for external decoupling capacitor."+      },+      {+        "number": "25",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground reference and exposed thermal pad for heat dissipation."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 90,+        "cost_usd": 0.7887,+        "at": "2026-09-23T12:54:53"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8565342028100886528",+        "pages": 90,+        "sha256": "d405f18ec87fd3ad",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file