3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownRTQ2522AGQW
Richtek Tech · Linear Voltage Regulators (LDO) · WDFN-10(3x3)
RTQ2522AGQW from Richtek Tech, in a WDFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input of the device, with a supply input voltage range of 0.8V to 5.5V. |
| 2 | VIN | power_in | Power input of the device, with a supply input voltage range of 0.8V to 5.5V. |
| 3 | PGOOD | output | Open-drain, active-high power good output indicating the status of VOUT, requiring a pull-up resistor of 10k to 1M to a supply of up to 5.5V. |
| 4 | VBIAS | power_in | Bias input that provides the voltage for internal control circuitry, with a VBIAS voltage range of 2.7V to 5.5V. |
| 5 | EN | input | Active-high chip enable; pulling it below 0.4V turns the regulator off, and it should be connected to VIN if not used. |
| 6 | GND | power_in | Ground connection that must be connected to the exposed pad for maximum power dissipation. |
| 7 | SS | passive | Connect a capacitor between this pin and ground to set the soft-start ramp time of the output voltage. |
| 8 | FB | input | Feedback pin that connects to an external voltage divider to set the output voltage against the 0.8V internal reference. |
| 9 | VOUT | power_out | Regulated output voltage; a minimum of 2.2μF capacitor should be placed directly at this pin, with an output voltage range of 0.8V to 3.6V. |
| 10 | VOUT | power_out | Regulated output voltage; a minimum of 2.2μF capacitor should be placed directly at this pin, with an output voltage range of 0.8V to 3.6V. |
| 11 | GND | power_in | Exposed pad that must be soldered to a large PCB and connected to GND for maximum power dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | WDFN-10(3x3) |
| Category | Power Management |
| Pins | 11 |
CAD (KiCad official)
- Symbol:
RTQ2522AGQW - Footprint:
Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mm - 3D model: WDFN-10(3x3) (KiCad packages3D, STEP)
- 3D model files:
rtq2522agqw-etched.step/rtq2522agqw-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rtq2522agqw.step/rtq2522agqw.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (17 pp, sha256
02d78142f38d01ac, retrieved 2026-10-27, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusoff(skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).