RT9711AGB

{
 "schema": "adom.pads/1",
 "slug": "rt9711agb",
 "footprint": "SOT-23-5",
 "generated_from": {
  "footprint": "SOT-23-5@sha256:455a3f7c3e5eb5b8",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -1.1375,
   -0.95
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOT-23-5@sha256:455a3f7c3e5eb5b8"
 },
 "pad_count": 5,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "FLG",
   "type": "output",
   "description": "Open-drain fault flag output. Asserts low (typ. 20 Ω pull-down, IFLG_OFF ≤ 1 μA leakage when off) after a 12 ms (typ.) delay when an over-current, thermal-shutdown, or reverse-current fault is detected. Requires an external 10 kΩ-100 kΩ pull-up resistor to the USB controller supply. Absolute-max flag voltage 6.5 V.",
   "is_pin1": true,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "GND",
   "type": "power_in",
   "description": "Device ground / return for the internal high-side switch, charge pump, bias, and logic. Tie to the system ground plane close to the CIN and COUT return paths.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "EN",
   "type": "input",
   "description": "Chip enable input (active-high on the RT9711A variant). Logic-high (VIH ≥ 2.0 V) turns the internal N-MOSFET switch on; logic-low (VIL ≤ 0.8 V) turns it off. Input range 0 V to 5.5 V, input leakage 0.01 μA typ. Must never be left floating. When disabled the pin is pulled low internally through ~75 Ω (RDS shutdown).",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "VIN",
   "type": "power_in",
   "description": "Power input to the internal high-side N-MOSFET switch and to the internal bias/charge-pump/UVLO circuitry. Recommended operating range 2.5 V to 5.5 V (absolute max 6.5 V). Decouple locally with a 1 μF CIN capacitor to GND. UVLO releases at ~1.7 V rising.",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    1.1375,
    -0.95
   ],
   "rot": 0.0,
   "size": [
    1.325,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "VOUT",
   "type": "power_out",
   "description": "Switched power output (drain of the internal N-MOSFET) to the downstream USB port/load. Delivers up to 1.5 A continuous (current limit ILIM = 2.5 A typ., 1.6-3.2 A). RDS(on) 80 mΩ typ. at VIN = 5 V, IOUT = 1 A. A low-ESR ≥150 μF aluminum/tantalum bulk capacitor plus a 10 μF ceramic to GND is recommended to meet the USB VBUS 330 mV droop requirement. Can be forced higher than VIN when off (no body diode).",
   "is_pin1": false,
   "source": {
    "geometry": "SOT-23-5.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}