Generated by kicad-footprint-generator · KiCad file format 20260206
| Name | Last updated |
|---|---|
| docs | |
| viewers | |
| package.json | |
| page.json | |
| README.md | |
| rt9467gqw-hero.glb | |
| rt9467gqw-hero.overlay.json | |
| rt9467gqw.glb | |
| rt9467gqw.kicad_mod | |
| rt9467gqw.kicad_sym | |
| rt9467gqw.lbr | |
| rt9467gqw.step |
RT9467GQW
Richtek Tech · Battery Management ICs · WQFN-24-EP(4x4)
RT9467GQW from Richtek Tech, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBUS | power_in | Power input. |
| 2 | D+ | bidirectional | USB D+ port used for USB host/charging port detection. |
| 3 | D- | bidirectional | USB D- port used for USB host/charging port detection. |
| 4 | STAT | output | Open-drain charge status output, low when charging is in progress and high when finished, blinking at 1Hz on a fault; connect a 2.2k-10kΩ pull-up resistor. |
| 5 | SCL | input | I2C interface serial clock input, open-drain, requires an external pull-up resistor. |
| 6 | SDA | bidirectional | I2C interface serial data input/output, open-drain, requires an external pull-up resistor. |
| 7 | INT | output | Active-low open-drain interrupt output indicating charger/Boost events for the system processor. |
| 8 | OTG | input | Active-high OTG boost mode enable control that acts with OTG_PIN_EN (Addr0x01[1]), with internal 102kΩ pull down. |
| 9 | CEB | input | Active-low charger enable input with internal 102kΩ pull down. |
| 10 | ILIM | input | Input current limit setting pin; a resistor to ground sets the maximum input current limit, and the actual limit is the lower of the ILIM and IAICR settings. |
| 11 | TS | input | Battery temperature-sense input connected to a resistor divider; if unused, connect 50kΩ to REGN and 50kΩ to ground. |
| 12 | QON | input | Internal BATFET enable control input; pulled low for tSHIPMODE (typical 0.9s) to exit shipping mode. |
| 13 | BAT | power_out | Charge current output node for battery connection, with the internal BATFET between SYS and BAT; connect a 10μF ceramic capacitor to ground. |
| 14 | BAT | power_out | Charge current output node for battery connection, with the internal BATFET between SYS and BAT; connect a 10μF ceramic capacitor to ground. |
| 15 | SYS | power_out | System connection node with the internal BATFET between SYS and BAT; connect a 20μF ceramic capacitor to ground. |
| 16 | SYS | power_out | System connection node with the internal BATFET between SYS and BAT; connect a 20μF ceramic capacitor to ground. |
| 17 | PGND | power_in | Power ground. |
| 18 | PGND | power_in | Power ground. |
| 19 | LX | passive | Switch node for output inductor connection. |
| 20 | LX | passive | Switch node for output inductor connection. |
| 21 | BTST | passive | Bootstrap capacitor connection for the high-side gate driver; connect a capacitor from BTST to LX. |
| 22 | REGN | power_out | Regulated output (4.9V when VBUS is plugged in) supplying the low-side gate driver and bootstrap capacitor; connect a 4.7μF ceramic capacitor to GND. |
| 23 | VMID | passive | Connection point between the reverse blocking MOSFET and the high-side switching MOSFET. |
| 24 | DSEL | output | Open-drain output that drives low during input source detection, stays low for DCP/HVDCP and goes high for SDP/CDP. |
| 25 | PGND | power_in | Exposed pad, power ground; must be connected to GND and well soldered to a large PCB copper area for maximum power dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | WQFN-24-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VBUS Supply Input Voltage | VBUS | -0.3 | 22 | V | 6 | ||
| VMID, BTST | -0.3 | 22 | V | 6 | |||
| LX | -0.3 | 16 | V | 6 | |||
| VMID-VBUS, BTST-LX | -0.3 | 6 | V | 6 | |||
| Other Pins | -0.3 | 6 | V | 6 | |||
| Power Dissipation | PD | 4.54 | W | TA = 25°C, WQFN-24L 4x4 | 6 | ||
| Lead Temperature | 260 | °C | Soldering, 10 sec. | 6 | |||
| Junction Temperature | TJ | 150 | °C | 6 | |||
| Storage Temperature Range | -65 | 150 | °C | 6 | |||
| ESD HBM | 2 | kV | Human Body Model | 6 | |||
| Thermal Resistance Junction-to-Ambient | θJA | 22 | °C/W | WQFN-24L 4x4, four-layer board | 6 | ||
| Thermal Resistance Junction-to-Case | θJC | 5.4 | °C/W | WQFN-24L 4x4, top of package | 6 | ||
| Supply Input Voltage | VBUS | 4 | 14 | V | 6 | ||
| Maximum Input Current (VBUS) | IAICR | 3.25 | A | 6 | |||
| Maximum SYS Output Current | ISYS | 5 | A | 6 | |||
| Maximum Battery Voltage | VBAT | 4.71 | V | 6 | |||
| Maximum IBAT Fast Charging Current | 5 | A | 6 | ||||
| Maximum IBAT Discharging Current | 6 | A | 6 | ||||
| Maximum IBAT Discharging Current peak | 9 | A | 1sec duration | 6 | |||
| Junction Temperature Range | TJ | -40 | 125 | °C | 6 | ||
| Ambient Temperature Range | TA | -40 | 85 | °C | 6 | ||
| VBUS Supply Current (non-switching) | IVBUS_NON_SW | 5 | mA | VLX Is non-switching, VBUS = 5V, VSYS = 4.4V | 6 | ||
| VBUS Supply Current (high-impedance) | IVBUS_HZ | 170 | μA | VLX is in high-impendence mode, VBUS = 5V, VSYS = 3.8V | 6 | ||
| VBUS Supply Current (switching) | IVBUS_SW | 8 | mA | VLX is switching, VBUS = 5V, VSYS = 3.8V | 6 | ||
| Battery Leakage Current (power path off) | IBAT_LEAK_OFF | 25 | μA | VBAT = 4.2V, power path is off | 6 | ||
| Battery Leakage Current | IBAT_LEAK_ON | 60 | μA | VBAT = 4.2V, SCL & SDA pull low, no VBUS. | 6 | ||
| Boost-Mode Battery Discharge Current | IBAT_BOOST_SW | 5 | mA | VBAT = 4.2V, boost mode, IVBUS = 0A, VLX is switching | 7 | ||
| Sleep-Mode Entry Threshold | VSLEEP_ENTER | 0 | 40 | 100 | mV | 2.5V < VBAT < VOREG, VBUS falling | 7 |
| Sleep-Mode Exit Threshold | VSLEEP_EXIT | 40 | 100 | 200 | mV | 2.5V < VBAT < VOREG , VBUS rising | 7 |
| Input Current Limit Factor | KILIM | 320 | 355 | 390 | AΩ | Input current regulation 508mA by ILIM pin with resistance = 698Ω | 7 |
| Input Current Limit Regulation minimum | IILIM_MIN | 0.5 | A | Minimum input current for regulation on ILIM pin | 7 | ||
| MIVR Threshold Range | VMIVR | 3.9 | 13.4 | V | I2C programmable in 0.1V steps | 7 | |
| MIVR Accuracy | VMIVR_ACC | -3 | 3 | % | VMIVR = 4.4V, 9V | 7 | |
| AICR Accuracy 100mA | IAICR_ACC | 86 | 93 | 100 | mA | USB charge mode, IAICR = 100mA | 7 |
| AICR Accuracy 500mA | IAICR_ACC | 440 | 470 | 500 | mA | USB charge mode, IAICR = 500mA | 7 |
| AICR Accuracy 1000mA | IAICR_ACC | 880 | 940 | 1000 | mA | USB charge mode, IAICR = 1000mA | 7 |
| AICR Accuracy 1500mA | IAICR_ACC | 1300 | 1400 | 1500 | mA | Adapter 1.5A charge mode, IAICR = 1500mA | 7 |
| VBUS Under-Voltage Protection Threshold | VUVLO | 3.05 | 3.3 | 3.55 | V | VBUS rising | 7 |
| Frequency Accuracy | fOSC_ACC | -10 | 10 | % | 10 | ||
| REGN Current Limit | ILIM_REGN | 50 | mA | VBUS = 5V / 9V / 12V | 10 | ||
| OTG Boost-Mode Output Regulation Voltage Range | VOTGBST | 4.425 | 5.825 | V | To VBUS | 10 | |
| OTG Boost-Mode Output Regulation Voltage Accuracy | VOTGBST_ACC | -3 | 3 | % | 10 | ||
| OTG Over-Load Protection Threshold | IOTG_OLP | 0.5 | 2.4 | A | I2C programmable | 10 | |
| OTG Default Over-Load Protection Threshold | IOTG_OLP_DEF | 0.5 | A | Addr 0x0A [2:0] = 000 | 10 | ||
| OTG Low Battery Protection Threshold | VOTG_LBP | 2.3 | 3.8 | V | I2C programmable, hysteresis = 0.4 V | 10 | |
| OTG Low Battery Protection Threshold Accuracy | -5 | 5 | % | 11 | |||
| Current Pulse Control Stop Pulse | tPUMPX_STOP | 430 | 570 | ms | 11 | ||
| Current Pulse Control Long On Pulse | tPUMPX_ON1 | 240 | 360 | ms | 11 | ||
| Current Pulse Control Short On Pulse | tPUMPX_ON2 | 70 | 130 | ms | 11 | ||
| Current Pulse Control Off Pulse | tPUMPX_OFF | 70 | 130 | ms | 11 | ||
| Current Pulse Control Stop Start Delay | tPUMPX_DLY | 80 | 225 | ms | 11 | ||
| I2C Output Low Threshold Voltage | VOL_I2C | 0.4 | V | IDS = 10mA | 11 | ||
| SCL, SDA Input Logic High Threshold Voltage | VIH_I2C | 1.3 | V | 11 | |||
| SCL, SDA Input Logic Low Threshold Voltage | VIL_I2C | 0.4 | V | 11 | |||
| SCL Clock | fSCL | 400 | kHz | 11 | |||
| High Level Leakage Current | IBIRS | 1 | μA | VPULL_UP = 1.8V, SDA and SCL | 11 | ||
| Load Capacitance | CLOAD | 1 | pF | VPULL_UP = 1.8V | 11 | ||
| Battery Temperature HOT Threshold | VVTS_HOT | 33.5 | 34.5 | 35.5 | % | VTS falling, the ratio of VREGN | 11 |
| Battery Temperature WARM Threshold | VVTS_WARM | 44 | 45 | 46 | % | VTS falling, the ratio of VREGN | 11 |
| Battery Temperature COOL Threshold | VVTS_COOL | 67.5 | 68.5 | 69.5 | % | VTS rising, the ratio of VREGN | 12 |
| Battery Temperature COLD Threshold | VVTS_COLD | 72.5 | 73.5 | 74.5 | % | VTS rising, the ratio of VREGN | 12 |
| Control I/O Output Low Voltage (STAT, INT) | VOL_CTRL | 0.4 | V | IDS = 10mA | 12 | ||
| Control I/O Input High Threshold (OTG, CEB, QON) | VIH_CTRL | 1.3 | V | Logic high threshold | 12 | ||
| Control I/O Input Low Threshold (OTG, CEB, QON) | VIL_CTRL | 0.4 | V | Logic low threshold | 12 | ||
| VDP_SRC Voltage | VDP_SRC | 0.5 | 0.65 | 0.7 | V | With IDAT_SRC = 0 to 250μA | 12 |
| VDAT_REF Voltage | VDAT_REF | 0.25 | 0.325 | 0.4 | V | 12 | |
| VLGC Voltage | VLGC | 0.8 | 1.2 | 2 | V | 12 | |
| IDM SINK Current | IDM_SINK | 50 | 100 | 150 | μA | May be a resistance if desired | 12 |
CAD (KiCad official)
- Symbol:
RT9467GQW - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
rt9467gqw-etched.step/rt9467gqw-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rt9467gqw.step/rt9467gqw.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (52 pp, sha256
ac9e072fa227b137, retrieved 2026-10-26, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).