component
RT9059GQW
Public Made by Adomby adom
Richtek Tech Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, WDFN-10(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownRT9059GQW
Richtek Tech · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · WDFN-10(3x3)
RT9059GQW from Richtek Tech, in a WDFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | power_out | Regulated output voltage; in adjustable mode VOUT is set between 0.8V and VIN by the external divider on ADJ. |
| 2 | VOUT | power_out | Regulated output voltage (pin 2 is tied to the same VOUT net as pins 1 and 3); the datasheet recommends a low-ESR ceramic output capacitor of at least 10µF located within 0.5 inch of the VOUT pin. |
| 3 | VOUT | power_out | Regulated output voltage (pin 3 is tied to the same VOUT net as pins 1 and 2); the datasheet recommends a low-ESR ceramic output capacitor of at least 10µF located within 0.5 inch of the VOUT pin. |
| 4 | ADJ | input | Output voltage setting; VOUT = VREF x (R1+R2)/R2 with VREF 0.8V typical, and R1/R2 should each be more than 10kΩ to limit power loss. |
| 5 | PGOOD | output | Open-drain power good output that goes high when VOUT reaches 90% of its nominal value; the datasheet specifies a 100kΩ pull-up to VOUT and sink voltage of 0.4V max at 10mA. |
| 6 | EN | input | Enable control input: logic high at 1.2V min and logic low at 0.4V max; the pin is pulled low internally, so the regulator is off when EN is floating. |
| 7 | VIN | power_in | Supply input voltage, 1V to 5.5V recommended; a 10µF or larger input capacitor placed close to the IC is recommended. |
| 8 | VIN | power_in | Supply input voltage, 1V to 5.5V recommended (pin 8 is tied to the same VIN net as pins 7 and 9). |
| 9 | VIN | power_in | Supply input voltage, 1V to 5.5V recommended (pin 9 is tied to the same VIN net as pins 7 and 8). |
| 10 | VDD | power_in | Supply voltage of the control circuit, 3V to 5.5V; VDD must be greater than VOUT + 1.5V. |
| 11 | GND | power_in | Ground; the exposed pad must be soldered to a large PCB and connected to GND for maximum power dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | WDFN-10(3x3) |
| Category | Power Management (PMIC) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Input Voltage, VIN | VIN | 1 | 5.5 | V | 4 | ||
| Control Voltage, VDD | VDD | 3 | 5.5 | V | VDD > VOUT + 1.5V | 4 | |
| Junction Temperature Range | -40 | 125 | °C | 4 | |||
| Ambient Temperature Range | -40 | 85 | °C | 4 | |||
| Supply Input Voltage, VIN to GND (DC) | VIN | -0.3 | 6 | V | DC | 4 | |
| Supply Input Voltage, VIN to GND (<10ms) | VIN | -0.3 | 7 | V | < 10ms | 4 | |
| Control Voltage, VDD to GND (DC) | VDD | -0.3 | 6 | V | DC | 4 | |
| Control Voltage, VDD to GND (<10ms) | VDD | -0.3 | 7 | V | < 10ms | 4 | |
| Output Voltage | VOUT | -0.3 | 6 | V | 4 | ||
| Chip Enable Voltage | EN | -0.3 | 6 | V | 4 | ||
| Adjust Voltage | ADJ | -0.3 | 6 | V | 4 | ||
| Power Good Voltage | VPGOOD | -0.3 | 6 | V | 4 | ||
| Power Dissipation, WDFN-10L 3x3 | PD | 2.95 | W | TA = 25°C | 4 | ||
| Junction Temperature | 150 | °C | 4 | ||||
| Lead Temperature (Soldering, 10 sec.) | 260 | °C | 10 sec. | 4 | |||
| Storage Temperature Range | -65 | 150 | °C | 4 | |||
| ESD Susceptibility HBM (Human Body Model) | 2 | kV | 4 | ||||
| ESD Susceptibility MM (Machine Model) | 200 | V | 4 | ||||
| VDD Operation Range | VDD | 3 | 5.5 | V | 4 | ||
| VDD POR Threshold | VPOR_VDD | 2.4 | 2.7 | 3 | V | VDD Rising | 4 |
| VDD POR Falling Hysteresis | VPOR_VDD | 0.15 | 0.2 | V | VDD Falling | 4 | |
| Input Voltage Range | VIN | 1 | 5.5 | V | 4 | ||
| VIN POR Threshold | VPOR_VIN | 0.7 | 0.8 | 0.9 | V | VIN Rising | 4 |
| VIN POR Falling Hysteresis | VPOR_VIN | 0.15 | 0.2 | 0.25 | V | VIN Falling | 4 |
| Quiescent Current | IQ | 0.6 | 1.2 | mA | EN On, No Load | 4 | |
| Reference Voltage | VREF | 0.788 | 0.8 | 0.812 | V | 5 | |
| VOUT Load Regulation | VLOAD | 0.5 | 1 | % | IOUT = 1mA to 3A, VIN = VOUT+1V | 5 | |
| OUT Line Regulation | VLINE | 0.2 | 0.6 | % | VDD = 3.6V to 5.5V, VIN = VOUT+1V to 5V, IOUT = 1mA | 5 | |
| Dropout Voltage | VDROP | 250 | 350 | mV | IOUT = 2A | 5 | |
| Dropout Voltage | VDROP | 350 | 450 | mV | IOUT = 3A | 5 | |
| Current Limit | ILIM | 3.1 | 3.6 | 4.2 | A | VIN = 3.6V | 5 |
| Short Circuit Current | ISC | 1 | 1.4 | 1.8 | A | VOUT < 0.2V | 5 |
| PGOOD Delay Time | 1 | 1.5 | ms | 5 | |||
| PGOOD Sink Capability | VPGOOD | 0.2 | 0.4 | V | ISINK = 10mA | 5 | |
| EN Input Logic-High Voltage | VIH | 1.2 | V | 5 | |||
| EN Input Logic-Low Voltage | VIL | 0.4 | V | 5 | |||
| EN Delay Time | 0.3 | 0.85 | 1.4 | ms | 5 | ||
| VDD Pin Shutdown Current | ISHDN_VDD | 1 | µA | VEN = 0V | 5 | ||
| VIN Pin Shutdown Current | ISHDN_VIN | 1 | µA | VEN = 0V, VIN = 5V | 5 | ||
| Soft-Start Time | tSS | 1.9 | 2.8 | 3.75 | ms | 5 | |
| VOUT Pull Low Resistance | RPULL | 150 | VEN = 0V | 5 | |||
| Thermal Shutdown Temperature | TSD | 160 | °C | 5 | |||
| Thermal Shutdown Recovery Temperature | TSDR | 90 | °C | 5 | |||
| PGOOD Rising Threshold | VTH_PGOOD | 90 | % | VOUT Rising | 5 | ||
| PGOOD Hysteresis | VTH_PGOOD | 10 | % | VOUT Falling | 5 | ||
| EN Pin Bias Current | IEN | 12 | µA | VEN = 5V | 5 | ||
| Inrush Current | IINRUSH | 0.5 | A | VOUT = 1.8V, COUT = 10µF, ILoad = 1A | 5 | ||
| Package Thermal Resistance, WDFN-10L 3x3, junction-to-ambient | θJA | 33.8 | °C/W | JEDEC 51-7 four-layer board, TA = 25°C | 4 | ||
| Package Thermal Resistance, WDFN-10L 3x3, junction-to-case | θJC | 8.9 | °C/W | measured at exposed pad | 4 |
CAD (KiCad official)
- Symbol:
RT9059GQW - Footprint:
Package_DFN_QFN:WDFN-10-1EP_3x3mm_P0.5mm_EP1.8x2.5mm - 3D model: WDFN-10(3x3), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
rt9059gqw-etched.step/rt9059gqw-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rt9059gqw.step/rt9059gqw.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (12 pp, sha256
9dc0d1b51e41c0c9, retrieved 2026-10-17, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).