3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownRT8462ZQW
Richtek Tech · LED Drivers · WQFN-16(3x3)
RT8462ZQW from Richtek Tech, in a WQFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RSET | passive | Switching frequency set pin; connect a resistor from RSET to GND, where RRSET = 30k sets fSW = 370kHz. |
| 2 | ISW | input | External MOSFET switch current sense; the sense resistor connects between the external N-MOSFET source and ground, with the ISW limit threshold of 80 to 145mV. |
| 3 | ISP | input | LED current sense amplifier positive input with common mode voltage up to 60V. |
| 4 | ISN | input | LED current sense amplifier negative input; the threshold between ISP and ISN is 190mV with common mode voltage up to 60V. |
| 5 | VC | passive | PWM control loop compensation pin; a series resistor and capacitor to GND (typically 10k and 3.3nF) set the loop response. |
| 6 | ACTL | input | Analog dimming control; the effective programming voltage range is 0.2V to 1.2V. |
| 7 | DCTL | input | PWM dimming input; with a filtering capacitor on ACTL, the PWM signal on this pin is averaged into an analog dimming signal on ACTL. |
| 8 | SS | passive | Soft-start pin; a capacitor of at least 10nF is required for proper soft-start. |
| 9 | EN | input | Chip enable, active high; when the pin voltage is low the chip is in shutdown mode. |
| 10 | OVP | input | Over voltage protection; the PWM converter turns off when the pin voltage goes higher than 1.18V. |
| 11 | VCC | power_in | Power supply pin of the chip with a recommended operating range of 6V to 36V; a low ESR bypass capacitor is required. |
| 12 | GND | power_in | Ground; connect to a large PCB ground plane for maximum power dissipation and noise reduction. |
| 13 | GBIAS | power_out | Internal gate driver bias output; a good bypass capacitor is required. |
| 14 | GATE | output | External MOSFET switch gate driver output. |
| 15 | NC | unconnected | No internal connection. |
| 16 | NC | unconnected | No internal connection. |
| 17 | GND | power_in | Exposed pad; must be soldered to a large PCB and connected to GND for maximum power dissipation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | WQFN-16(3x3) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Current | IVCC | 6 | 7.2 | mA | VVC ≥ 0.4V (Switching off) | 5 | |
| EN Threshold Voltage Logic-High | VIH | 2 | V | 5 | |||
| EN Threshold Voltage Logic-Low | VIL | 0.5 | V | 5 | |||
| EN Input Current | IEN | 1.2 | μA | VEN ≤ 3V | 5 | ||
| Current Sense Amplifier Input Threshold | VISP−VISN | 182 | 190 | 198 | mV | VACTL ≥ 1.25V, 12V ≤ common mode ≤ 60V | 5 |
| Supply Input Voltage Range | VCC | 6 | 36 | V | 5 | ||
| Junction Temperature Range | TJ | -40 | 125 | °C | 5 | ||
| Supply Input Voltage | VCC | -0.3 | 38 | V | 5 | ||
| GBIAS, GATE Voltage | VGBIAS, VGATE | -0.3 | 10 | V | 5 | ||
| ISW Voltage | VISW | -0.3 | 1 | V | 5 | ||
| ISP, ISN Voltage | VISP, VISN | -0.3 | 66 | V | 5 | ||
| DCTL, ACTL, OVP Voltage | VDCTL, VACTL, VOVP | -0.3 | 8 | V | Note 2 | 5 | |
| EN Voltage | VEN | -0.3 | 20 | V | 5 | ||
| Power Dissipation WQFN-16L 3x3 | PD | 1.471 | W | TA = 25°C | 5 | ||
| Package Thermal Resistance WQFN-16L 3x3 Junction to Ambient | θJA | 68 | °C/W | 5 | |||
| Package Thermal Resistance WQFN-16L 3x3 Junction to Case | θJC | 7.5 | °C/W | 5 | |||
| Junction Temperature | TJ | 150 | °C | 5 | |||
| Lead Temperature | 260 | °C | Soldering, 10 sec. | 5 | |||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 5 | ||
| ESD Susceptibility HBM | 2 | kV | Human Body Model | 5 | |||
| ESD Susceptibility MM | 200 | V | Machine Model | 5 | |||
| DCTL Input Current | IDCTL | 0.5 | μA | 0.3V ≤ VDCTL ≤ 5V | 6 | ||
| DCTL Threshold Voltage High | VDCTL_H | 2 | V | 6 | |||
| DCTL Threshold Voltage Low | VDCTL_L | 0.3 | V | 6 | |||
| Switching Frequency | fSW | 280 | 370 | 450 | kHz | RRSET = 30k | 6 |
| GBIAS Voltage | VGBIAS | 7.8 | 8.5 | 9.2 | V | IGBIAS = 20mA | 6 |
| GATE Voltage High | VGATE_H | 6 | 7.2 | 7.8 | V | IGATE = 50mA | 6 |
| GATE Voltage High | VGATE_H | 7.5 | 7.8 | 7.9 | V | IGATE = 100μA | 6 |
| GATE Voltage Low | VGATE_L | 0.5 | 1 | V | IGATE = 10mA | 6 | |
| GATE Voltage Low | VGATE_L | 0.1 | 0.9 | V | IGATE = 100μA | 6 | |
| GATE Drive Rise and Fall Time | 20 | 100 | ns | 1nF Load at GATE | 6 | ||
| PWM Switch Current Limit Threshold | ISW_LIM | 80 | 110 | 145 | mV | 6 | |
| OVP Input Current | IOVP | 0.1 | μA | 0.7V ≤ VOVP ≤ 1.5V | 6 |
CAD (KiCad official)
- Symbol:
RT8462ZQW - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
rt8462zqw-etched.step/rt8462zqw-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rt8462zqw.step/rt8462zqw.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (16 pp, sha256
7d8f2d7c236db662, retrieved 2026-10-27, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusoff(skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).