← Commit history
page.json+11−8@@ -32,7 +32,7 @@ "number": "1", "name": "VIN", "type": "power_in",- "description": "Power input. Supply range 2.95V to 6V (absolute max \u22120.3V to 7V). Tie pins 1, 2, and 16 together and bypass to GND with a low-ESR ceramic capacitor."+ "description": "Power input. Supply range 2.95V to 6V (absolute max −0.3V to 7V). Tie pins 1, 2, and 16 together and bypass to GND with a low-ESR ceramic capacitor." }, { "number": "2",@@ -74,19 +74,19 @@ "number": "8", "name": "RT/SYNC", "type": "bidirectional",- "description": "Frequency setting and external synchronous clock input. Connect a resistor RRT to GND to set the switching frequency (700kHz to 2MHz; e.g. 180k\u03a9 \u2192 ~1MHz, 60k\u03a9 \u2192 ~2.2MHz), or drive with an external clock in the 700kHz-2MHz range to synchronize."+ "description": "Frequency setting and external synchronous clock input. Connect a resistor RRT to GND to set the switching frequency (700kHz to 2MHz; e.g. 180kΩ → ~1MHz, 60kΩ → ~2.2MHz), or drive with an external clock in the 700kHz-2MHz range to synchronize." }, { "number": "9", "name": "SS/TR", "type": "passive",- "description": "Soft-start and tracking. An internal 2.2\u00b5A current source charges an external CSS capacitor to set the soft-start ramp; VFB tracks VSS during startup. CSS(nF) = tSS(ms) \u00d7 2.2\u00b5A / 0.827V."+ "description": "Soft-start and tracking. An internal 2.2µA current source charges an external CSS capacitor to set the soft-start ramp; VFB tracks VSS during startup. CSS(nF) = tSS(ms) × 2.2µA / 0.827V." }, { "number": "10", "name": "SW", "type": "power_out",- "description": "Switch node. Connect to external inductor of the L-C output filter. Voltage rating \u22121V to (VIN + 0.3V) DC, \u22125V to (VIN + 5V) for <100ns transients. Pins 10, 11, 12 are tied internally and must all connect to the inductor."+ "description": "Switch node. Connect to external inductor of the L-C output filter. Voltage rating −1V to (VIN + 0.3V) DC, −5V to (VIN + 5V) for <100ns transients. Pins 10, 11, 12 are tied internally and must all connect to the inductor." }, { "number": "11",@@ -104,7 +104,7 @@ "number": "13", "name": "BOOT", "type": "power_in",- "description": "Bootstrap supply for the high-side MOSFET gate driver. Connect a ~0.1\u00b5F capacitor between BOOT and SW. BOOT-to-SW absolute max \u22120.3V to 7V."+ "description": "Bootstrap supply for the high-side MOSFET gate driver. Connect a ~0.1µF capacitor between BOOT and SW. BOOT-to-SW absolute max −0.3V to 7V." }, { "number": "14",@@ -116,7 +116,7 @@ "number": "15", "name": "EN", "type": "input",- "description": "Chip enable. Pull high (>1.25V typ rising) to enable, low (<1.18V typ falling) to disable. Internal pull-up current source (~4.9\u00b5A at VIH+50mV) enables the chip when the pin is left floating. External resistor divider from VIN can set a custom UVLO."+ "description": "Chip enable. Pull high (>1.25V typ rising) to enable, low (<1.18V typ falling) to disable. Internal pull-up current source (~4.9µA at VIH+50mV) enables the chip when the pin is left floating. External resistor divider from VIN can set a custom UVLO." }, { "number": "16",@@ -128,7 +128,7 @@ "number": "17", "name": "GND", "type": "power_in",- "description": "Exposed thermal pad. Must be soldered to a large PCB ground copper area and connected to GND for maximum power dissipation (\u03b8JC = 7.5\u00b0C/W, \u03b8JA = 30\u00b0C/W)."+ "description": "Exposed thermal pad. Must be soldered to a large PCB ground copper area and connected to GND for maximum power dissipation (θJC = 7.5°C/W, θJA = 30°C/W)." } ], "provenance": {@@ -192,5 +192,8 @@ "docs/rt2101agqw-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }