main
History Download
Ray rs3235yek: laser-etched CAD + chip hero (factory 2.0.0 backfill) aa93d6b

RS3235YEK

Jiangsu RUNIC Tech · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · ESOP8

RS3235YEK from Jiangsu RUNIC Tech, in a ESOP8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 POK output Power-OK signal output. Open-drain output that indicates the status of the output voltage by sensing FB voltage. Pulled low when output voltage is not within the Power-OK voltage window (rising threshold ~93% of VFB, hysteresis ~8%). Requires external pull-up resistor.
2 EN input Active-high enable control pin. Applying voltage above ~1.2V enables the regulator (new soft-start each time); pulling below ~0.5V shuts down the output. When left open, an internal 800-2000kΩ pull-low resistor pulls EN low and shuts down the regulator. Max 6.0V.
3 VIN power_in Main supply input pin for voltage conversion. Recommended operating range 1.0V to 6.0V. A decoupling capacitor (≥10μF) should be placed near this pin for filtering and transient response. Voltage is monitored for Power-On-Reset (rising POR threshold typ 0.9V).
4 VCNTL power_in Bias voltage input for internal control circuitry. Connect to a voltage source (+5V recommended, operating range 3.0V to 6.0V). A 0.1μF decoupling capacitor is typically placed near this pin. Voltage is monitored for Power-On-Reset (rising POR threshold typ 2.7V).
5 NC unconnected No Connection. Not internally bonded; leave floating or tie to GND per layout preference.
6 VOUT power_out Regulator output pin. Connect a load capacitor (≥10μF, ESR 0-200mΩ) for stability and transient response. Output voltage is programmed by external resistor divider to FB. Provides up to 3A continuous / 4A peak. During shutdown, VOUT is discharged by an internal ~55Ω pull-low MOSFET.
7 FB input Voltage feedback pin. Connect to an external resistor divider from VOUT to set output voltage; internal reference VREF = 0.8V. FB input current is ±100nA max. Also sensed by the POK comparator.
8 GND power_in Ground pin of the circuitry. Connect to system ground plane; provides return path for both bias and power currents.

Key specifications

Parameter Value
Manufacturer Jiangsu RUNIC Tech
Package ESOP8
Category PMIC
Pins 8

Ordering variants

Same part, different packaging or reel option.

  • RS3235YEK
  • RS3235YEKYTDC10

CAD (KiCad official)

  • Symbol: RS3235YEK
  • Footprint: Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm
  • 3D model: ESOP8 (KiCad packages3D, STEP)
  • 3D model files: rs3235yek-etched.step / rs3235yek-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); rs3235yek.step / rs3235yek.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Jiangsu RUNIC Tech datasheet (21 pp, sha256 9e844e456273e744, retrieved 2026-08-17, tier: lcsc)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF