component
RN2025
Public Made by Adomby adom
RENERGY Energy Metering ICs, LQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
28cdddc
RN2025
RENERGY · Energy Metering ICs · LQFP-64(10x10)
RN2025 from RENERGY, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVCC1 | power_in | Metering ADC supply input; isolate from AVCC2 with a 10 Ω resistor and decouple with 1 µF in parallel with 0.1 µF. |
| 2 | IBN | input | Current channel B negative fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 3 | IBP | input | Current channel B positive fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 4 | IAN | input | Current channel A negative fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 5 | IAP | input | Current channel A positive fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 6 | AVSS1 | power_in | Analog ground of the internal metering ADC. |
| 7 | AVSS2 | power_in | Analog ground of the self-check (EDT) circuit. |
| 8 | UASP_400 | output | Outputs a 400 µA current-source square wave for phase-A voltage fault detection; if self-check is unused it may float on RN2025A64/B64, but on RN2025C64 it must follow the self-check wiring and WriteUEdtVBCtlReg must be called. |
| 9 | RP | output | Typical output voltage 1.25 V; connect an external 6.2 kΩ resistor to ground, of the same resistor type as the voltage-divider resistors, to set the voltage self-check reference current. |
| 10 | P60/SDAIN8/CF0/RTC_OUT | bidirectional | GPIO P60 multiplexed with GPADC input SDAIN8 (for DC test), CF0 pulse output and RTC_OUT. |
| 11 | ISP | output | Outputs a 2 V square wave for the P side of the current-channel self-check circuit; connect a low-tempco resistor of about 49.9 Ω, and float it if self-check is unused. |
| 12 | AVCC2 | power_in | Self-check circuit supply; decouple with 220 µF in parallel with 10 µF plus 0.1 µF and provide at least 50 mA of supply capability. |
| 13 | P44/SDAIN0/TX4/INT6 | bidirectional | GPIO P44 multiplexed with GPADC input SDAIN0, UART4 TX (cannot be configured as IR-modulated output) and INT6. |
| 14 | P45/SDAIN1/RX4/INT7 | bidirectional | GPIO P45 multiplexed with GPADC input SDAIN1, UART4 RX and INT7. |
| 15 | P46/SDAIN2/TX5/KEY6 | bidirectional | GPIO P46 multiplexed with GPADC input SDAIN2, UART5 TX (cannot be configured as IR-modulated output) and KEY6. |
| 16 | P47/SDAIN3/RX5/KEY7/CF4/CF0/RTCOUT | bidirectional | GPIO P47 multiplexed with GPADC input SDAIN3, UART5 RX, KEY7, CF4, CF0 and RTCOUT. |
| 17 | DVCC | power_in | Digital supply input; decouple with 1 µF plus 0.1 µF and isolate from AVCC2 with a 10 Ω resistor. |
| 18 | DGND | power_in | Digital ground of the internal LDO18 domain. |
| 19 | LDO18 | power_out | Internal 1.8 V LDO output that powers the 1.8 V digital domain; decouple with 1 µF plus 0.1 µF. |
| 20 | RSTN | input | Active-low external reset with an internal pull-up of about 50 kΩ and CMOS input level; a low level longer than 1 ms causes reset. |
| 21 | P00/CMP0/INT0/CF2 | bidirectional | GPIO P00 multiplexed with comparator CMP0 input, INT0 and CF2; the default configuration gives the comparator an internal ~600 kΩ pull-down to ground. |
| 22 | P02/CF0/RTCOUT/SDAIN5 | bidirectional | GPIO P02 with 6 mA drive, multiplexed with CF0 pulse output, RTCOUT (RTC 1 Hz output) and GPADC input SDAIN5. |
| 23 | P03/CF1/TCI/TC0_P[0]/RTC_OUT/RTC_1s | bidirectional | GPIO P03 with 6 mA drive, multiplexed with CF1 pulse output, timer 0 input/output, RTC_OUT and RTC_1S. |
| 24 | P06/INT1/SCSN0_1_2 | bidirectional | GPIO P06 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with INT1 and the SPI0/1/2 chip-select (slave mode only). |
| 25 | P07/KEY1/SCLK0_1_2 | bidirectional | GPIO P07 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with KEY1 and the SPI0/1/2 clock. |
| 26 | P10/INT2/MOSI0_1/SDI2 | bidirectional | GPIO P10 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with INT2 and the SPI MOSI/SDI. |
| 27 | P11/KEY2/MISO0_1/SDO2 | bidirectional | GPIO P11 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with KEY2 and the SPI MISO/SDO. |
| 28 | P12/SCSN0_1_2/TCI/TC0_P[0] | bidirectional | GPIO P12 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI0/1/2 chip-select, timer input and timer 0 output. |
| 29 | P13/SCLK0_1_2/TCI/TC0_N[0] | bidirectional | GPIO P13 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI0/1/2 clock, timer input and timer 0 output. |
| 30 | P14/MOSI0_1/SDI2/TCI/TC0_P[1] | bidirectional | GPIO P14 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MOSI/SDI, timer input and timer 0 output. |
| 31 | P15/MISO0_1/SDO2/TCI/TC0_N[1] | bidirectional | GPIO P15 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MISO/SDO, timer input and timer 0 output. |
| 32 | P16/HOSCO/INT3/SCSN3 | bidirectional | High-frequency crystal output (8.192, 16.384 or 32.768 MHz) multiplexed with GPIO P16, INT3 and SPI3 chip-select; add a 10 MΩ series resistor and two 15-22 pF load capacitors, and select a crystal with load capacitance below 15 pF. |
| 33 | P17/HOSCI/INT4/SCLK3 | bidirectional | High-frequency crystal input multiplexed with GPIO P17, INT4 and SPI3 clock; P16 and P17 select HOSC together. |
| 34 | DGND | power_in | Digital ground. |
| 35 | SWDCLK/P20/RX1/RX2/CF3/RTC_1s/TC0_P[1] | bidirectional | SWD clock multiplexed with GPIO P20, UART1/UART2 RX, CF3, RTC_1S and timer 0 output; SWD pins are pulled up by default after power-up. |
| 36 | SWDIO/P21/TX1/TX2/CF2/TC0_P[0]/RTC_OUT | bidirectional | SWD data multiplexed with GPIO P21, UART1/UART2 TX, CF2, timer 0 output and RTC_OUT; SWD pins are pulled up by default after power-up. |
| 37 | P30/ISPEN/TCI/KEY3/CF4/TC1_P[1]/RTC_OUT | bidirectional | GPIO P30 with 6 mA drive; the BOOTROM samples this pin after reset and enters ISP if it is low, so the application must account for this. |
| 38 | P22/RX2/KEY4/MOSI3/TC1_N[0]/CF4 | bidirectional | GPIO P22 multiplexed with UART2 RX, KEY4, SPI3 MOSI, timer 1 output and CF4. |
| 39 | P23/TX2/KEY5/MISO3/TC1_P[0]/RTC_OUT | bidirectional | GPIO P23 multiplexed with UART2 TX, KEY5, SPI3 MISO, timer 1 output and RTC_OUT. |
| 40 | P24/SCL/TCI/TC1_P[0]/SCSN4/CF4 | bidirectional | GPIO P24 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with I2C SCL, timer input/output, SPI4 chip-select and CF4. |
| 41 | P25/SDA/TCI/TC1_P[1]/SCLK4/RTC_OUT | bidirectional | GPIO P25 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with I2C SDA, timer input/output, SPI4 clock and RTC_OUT. |
| 42 | P26/RX3/TCI/TC1_N[0]/CF2/RTC_OUT/MOSI4 | bidirectional | GPIO P26 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with UART3 RX, timer, CF2, RTC_OUT and SPI4 MOSI. |
| 43 | P27/TX3/TCI/TC1_N[1]/CF3/RTC_1s/MISO4 | bidirectional | GPIO P27 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with UART3 TX, timer, CF3, RTC_1S and SPI4 MISO. |
| 44 | P31/SDO2/MISO0_1/SCL/CF4/RTC_OUT | bidirectional | GPIO P31 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MISO/SDO, I2C SCL, CF4 and RTC_OUT. |
| 45 | P32/SDI2/MOSI0_1/SDA/CF3/RTC_1S | bidirectional | GPIO P32 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MOSI/SDI, I2C SDA, CF3 and RTC_1S. |
| 46 | P33/SCLK2/SCLK0_1/RX2/CF2/RTC_OUT/RTC_1S | bidirectional | GPIO P33 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI clock, UART2 RX, CF2, RTC_OUT and RTC_1S. |
| 47 | P34/SCSN2/SCSN0_1/TX2/CF1/RTC_OUT/RTC_1S | bidirectional | GPIO P34 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI chip-select, UART2 TX, CF1, RTC_OUT and RTC_1S. |
| 48 | LXO | passive | 32.768 kHz passive crystal output; no external resistor or capacitor is needed (on-chip), and it must be guarded from neighbouring signals by ground. |
| 49 | LXI | passive | 32.768 kHz passive crystal input, paired with LXO; no external resistor or capacitor is needed and it must be guarded by ground. |
| 50 | BVSS | power_in | Ground of the VBAT domain. |
| 51 | LDO_VBAT | power_out | VBAT-domain LDO output; requires an external 0.22 µF capacitor. |
| 52 | VBAT | power_in | 3.6 V battery or supercapacitor input that powers only the RTC; it is also the SAR ADC input (two internal 300 kΩ divider resistors, 0.5× gain), and an RC filter of 10 Ω and 1 µF is recommended. |
| 53 | VREFB | output | SAR ADC internal reference output, typically 1.25 V; requires an external 0.22 µF capacitor. |
| 54 | P40/KEY6/AIN3 | bidirectional | VBAT-domain GPIO P40 with KEY6 and SAR ADC input AIN3, which can measure up to 3.6 V at 0.5× PGA; the input-high level must not exceed VBAT. |
| 55 | P41/KEY7/AIN2 | bidirectional | VBAT-domain GPIO P41 with KEY7 and SAR ADC input AIN2; the input range must not exceed 1.25 V (PGA=1), 2.5 V (PGA=0.5) or the supply (PGA=0.2). |
| 56 | P42/RTCOUT2/AIN1/SCL/KEY6/RTC_1S | bidirectional | VBAT-domain GPIO P42 with RTCOUT, SAR ADC input AIN1 (range as P41), I2C SCL, KEY6 and RTC_1S; it is not recommended to connect a battery here because it drives RTCOUT while VBAT alone is powered. |
| 57 | P43/AIN0/SDA/KEYOUT | bidirectional | VBAT-domain GPIO P43 with SAR ADC input AIN0 (range as P41), I2C SDA and KEYOUT, which is a key-event power control output for external EEPROM. |
| 58 | P50/AIN4/KEY6/RTC_OUT | bidirectional | VBAT-domain GPIO P50 with SAR ADC input AIN4 (range as P41), KEY6 and RTC_OUT. |
| 59 | P51/AIN5/KEYOUT/RTC_1S | bidirectional | VBAT-domain GPIO P51 with SAR ADC input AIN5 (range as P41), KEYOUT and RTC_1S. |
| 60 | UAN | input | Voltage channel A negative fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 61 | UAP | input | Voltage channel A positive fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 62 | AVSS3 | power_in | Analog ground of the internal voltage reference. |
| 63 | VREFA | output | ADC reference, typically 1.25 V; requires 0.1 µF and 1 µF external capacitors. |
| 64 | LDO3 | power_out | Metering ADC supply LDO, typically 3 V; requires 0.1 µF and 1 µF external capacitors. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENERGY |
| Package | LQFP-64(10x10) |
| Category | ADC/DAC/Data Conversion |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 有功电能测量误差 | Err | -0.1 | 0.1 | % | 8000:1动态范围 | 30 | |
| 无功电能测量误差 | Err | -0.1 | 0.1 | % | 8000:1动态范围 | 30 | |
| 视在电能测量误差 | Err | -0.1 | 0.1 | % | 8000:1动态范围 | 30 | |
| 有效值测量误差 | Err | -0.2 | 0.2 | % | 2000:1动态范围 | 30 | |
| 功率测量误差 | Err | -0.1 | 0.1 | % | 2000:1动态范围 | 30 | |
| 全失压电流测量误差 | -0.5 | 0.5 | % | 400:1动态范围 | 30 | ||
| 最大信号电平(差分, PGA=1) | Vxn | -1000 | 1000 | mVp | PGA=1,差分信号 | 30 | |
| 频率测量范围 | 40 | 75 | Hz | 30 | |||
| 电能脉冲输出最大频率 | 20 | KHz | 当脉宽低于 84ms 时 | 30 | |||
| 基准电压输出 | Vref | 1.25 | 1.26 | 1.27 | V | VCC=3V~5.5V,温度范围:-40℃~+85℃ | 30 |
| SAR ADC 输入范围 | SAR-IN | 0 | V | 最大值为 BGR(内部低功耗基准,典型值 1.25V) | 30 | ||
| 低功耗比较器 LVD 阈值 | LVD | 2.3 | 4.9 | V | LVD 阈值可配置,2.3V 到 4.9V | 30 | |
| 低功耗比较器 CMP0 阈值 Vil1 | Vil1 | 1.23 | 1.28 | 1.33 | V | 默认配置下比较器输出低电平的阈值 | 30 |
| 低功耗比较器 CMP0 阈值 Vil2 | Vil2 | 0.8 | 0.84 | 0.88 | V | 选择0.9V档并且选择有迟滞时 | 30 |
| VBAT 测量范围 | VBAT | 0 | 3.6 | 5 | V | SAR ADC 对 VBAT 引脚电压的测量范围 | 30 |
| 输入高频时钟频率范围 | HOSI | 4.096 | 16.384 | 32.768 | Mhz | 31 | |
| 内部PLL时钟频率范围 | PLL | 8.192 | 16.384 | MHz | fosc=32.768Khz | 31 | |
| 内部高频RCH(常温) | RCH | 3 | 3.2 | 3.85 | MHz | 常温,用于芯片复位后默认 | 31 |
| 内部低频RCL | RCL | 20 | 32 | 40 | KHz | 用于WDT时钟 | 32 |
| 主电源 VCC | VCC | 2.4 | 5.5 | V | 建议主电源选择为3.3V±5%或者5V±5% | 32 | |
| CPU 最低工作电压 | Vil | 1.8 | 1.9 | 2 | V | 全温度范围 | 32 |
| VBAT 供电电压 VBAT1 | VBAT1 | 2.5 | 3.6 | 5.5 | V | RTC 温补电路正常工作,RTC 精度保证的电压工作范围 | 32 |
| VBAT 供电电压 VBAT2 | VBAT2 | 1.8 | 3.6 | 5.5 | V | RTC 万年历翻转正常,温补电路不保证 | 32 |
| VBAT 供电功耗(典型) | SIdd | 1.5 | μA | 典型条件:Vbat=3.6V;Tc=25度 | 32 | ||
| VBAT 供电功耗(极限) | SIdd | 2 | μA | 极限条件:Vbat=3.6V;Tc=85度 | 32 | ||
| LDO18 内核电压 | V1P8 | 1.62 | 1.8 | 1.98 | V | CPU 内核电压 | 32 |
| LDO3 Σ-ΔADC 电压 | V3 | 2.85 | 2.9 | 2.95 | V | Σ-ΔADC 电压 | 32 |
| LDO_VBAT VBAT域数字电压 | V2 | 1.9 | 2 | 2.2 | V | VBAT 域数字电压 | 32 |
| 主电电压 | Vvcc | -0.3 | 7 | V | 32 | ||
| 电池输入电压 | Vvbat | -0.3 | 7 | V | 32 | ||
| DVDD to DGND | -0.3 | 7 | V | 32 | |||
| DVDD to AVDD | -0.3 | 0.3 | V | 32 | |||
| 电流输入引脚电压 | IAP,IAN,IBP,IBN,ICP,ICN,INP,INN | -6 | 6 | V | 32 | ||
| 电压输入引脚电压 | VAP,VAN,VBP,VBN,VCP,VCN | -6 | 6 | V | 32 | ||
| 数字IO输出低电平 | VOL | -0.3 | V | 33 | |||
| 模拟输入电压(相对AGND) | VINA | -0.3 | V | 相对于 AGND;上限为 AVDD+0.3(表中为表达式) | 33 | ||
| 工作温度范围 | TA | -40 | 85 | ℃ | 33 | ||
| 存储温度范围 | Tstg | -65 | 150 | ℃ | 33 | ||
| ESD 人体模型 HBM | ESD | 4000 | V | HBM,JEDEC EIA/JESD22-A114,所有引脚 | 33 | ||
| ESD 机械模型 MM | ESD | 200 | V | MM,JEDEC EIA/JESD22-A115C,所有引脚 | 33 | ||
| ESD 充电器件模型 CDM | ESD | 500 | V | CDM,JEDEC EIA/JESD22-C101F,所有引脚 | 33 | ||
| 闩锁试验 Latch-up | LatchUp | 200 | mA | JEDEC STANDARD NO.78D NOVEMBER 2011,所有引脚 | 33 |
CAD (KiCad official)
- Symbol:
RN2025 - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
rn2025-etched.step/rn2025-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rn2025.step/rn2025.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENERGY datasheet (301 pp, sha256
bae190d83688b304, retrieved 2026-11-13, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# RN2025
**RENERGY** · Energy Metering ICs · LQFP-64(10x10)
RN2025 from RENERGY, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVCC1 | power_in | Metering ADC supply input; isolate from AVCC2 with a 10 Ω resistor and decouple with 1 µF in parallel with 0.1 µF. |
| 2 | IBN | input | Current channel B negative fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 3 | IBP | input | Current channel B positive fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 4 | IAN | input | Current channel A negative fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 5 | IAP | input | Current channel A positive fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 6 | AVSS1 | power_in | Analog ground of the internal metering ADC. |
| 7 | AVSS2 | power_in | Analog ground of the self-check (EDT) circuit. |
| 8 | UASP_400 | output | Outputs a 400 µA current-source square wave for phase-A voltage fault detection; if self-check is unused it may float on RN2025A64/B64, but on RN2025C64 it must follow the self-check wiring and WriteUEdtVBCtlReg must be called. |
| 9 | RP | output | Typical output voltage 1.25 V; connect an external 6.2 kΩ resistor to ground, of the same resistor type as the voltage-divider resistors, to set the voltage self-check reference current. |
| 10 | P60/SDAIN8/CF0/RTC_OUT | bidirectional | GPIO P60 multiplexed with GPADC input SDAIN8 (for DC test), CF0 pulse output and RTC_OUT. |
| 11 | ISP | output | Outputs a 2 V square wave for the P side of the current-channel self-check circuit; connect a low-tempco resistor of about 49.9 Ω, and float it if self-check is unused. |
| 12 | AVCC2 | power_in | Self-check circuit supply; decouple with 220 µF in parallel with 10 µF plus 0.1 µF and provide at least 50 mA of supply capability. |
| 13 | P44/SDAIN0/TX4/INT6 | bidirectional | GPIO P44 multiplexed with GPADC input SDAIN0, UART4 TX (cannot be configured as IR-modulated output) and INT6. |
| 14 | P45/SDAIN1/RX4/INT7 | bidirectional | GPIO P45 multiplexed with GPADC input SDAIN1, UART4 RX and INT7. |
| 15 | P46/SDAIN2/TX5/KEY6 | bidirectional | GPIO P46 multiplexed with GPADC input SDAIN2, UART5 TX (cannot be configured as IR-modulated output) and KEY6. |
| 16 | P47/SDAIN3/RX5/KEY7/CF4/CF0/RTCOUT | bidirectional | GPIO P47 multiplexed with GPADC input SDAIN3, UART5 RX, KEY7, CF4, CF0 and RTCOUT. |
| 17 | DVCC | power_in | Digital supply input; decouple with 1 µF plus 0.1 µF and isolate from AVCC2 with a 10 Ω resistor. |
| 18 | DGND | power_in | Digital ground of the internal LDO18 domain. |
| 19 | LDO18 | power_out | Internal 1.8 V LDO output that powers the 1.8 V digital domain; decouple with 1 µF plus 0.1 µF. |
| 20 | RSTN | input | Active-low external reset with an internal pull-up of about 50 kΩ and CMOS input level; a low level longer than 1 ms causes reset. |
| 21 | P00/CMP0/INT0/CF2 | bidirectional | GPIO P00 multiplexed with comparator CMP0 input, INT0 and CF2; the default configuration gives the comparator an internal ~600 kΩ pull-down to ground. |
| 22 | P02/CF0/RTCOUT/SDAIN5 | bidirectional | GPIO P02 with 6 mA drive, multiplexed with CF0 pulse output, RTCOUT (RTC 1 Hz output) and GPADC input SDAIN5. |
| 23 | P03/CF1/TCI/TC0_P[0]/RTC_OUT/RTC_1s | bidirectional | GPIO P03 with 6 mA drive, multiplexed with CF1 pulse output, timer 0 input/output, RTC_OUT and RTC_1S. |
| 24 | P06/INT1/SCSN0_1_2 | bidirectional | GPIO P06 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with INT1 and the SPI0/1/2 chip-select (slave mode only). |
| 25 | P07/KEY1/SCLK0_1_2 | bidirectional | GPIO P07 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with KEY1 and the SPI0/1/2 clock. |
| 26 | P10/INT2/MOSI0_1/SDI2 | bidirectional | GPIO P10 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with INT2 and the SPI MOSI/SDI. |
| 27 | P11/KEY2/MISO0_1/SDO2 | bidirectional | GPIO P11 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with KEY2 and the SPI MISO/SDO. |
| 28 | P12/SCSN0_1_2/TCI/TC0_P[0] | bidirectional | GPIO P12 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI0/1/2 chip-select, timer input and timer 0 output. |
| 29 | P13/SCLK0_1_2/TCI/TC0_N[0] | bidirectional | GPIO P13 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI0/1/2 clock, timer input and timer 0 output. |
| 30 | P14/MOSI0_1/SDI2/TCI/TC0_P[1] | bidirectional | GPIO P14 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MOSI/SDI, timer input and timer 0 output. |
| 31 | P15/MISO0_1/SDO2/TCI/TC0_N[1] | bidirectional | GPIO P15 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MISO/SDO, timer input and timer 0 output. |
| 32 | P16/HOSCO/INT3/SCSN3 | bidirectional | High-frequency crystal output (8.192, 16.384 or 32.768 MHz) multiplexed with GPIO P16, INT3 and SPI3 chip-select; add a 10 MΩ series resistor and two 15-22 pF load capacitors, and select a crystal with load capacitance below 15 pF. |
| 33 | P17/HOSCI/INT4/SCLK3 | bidirectional | High-frequency crystal input multiplexed with GPIO P17, INT4 and SPI3 clock; P16 and P17 select HOSC together. |
| 34 | DGND | power_in | Digital ground. |
| 35 | SWDCLK/P20/RX1/RX2/CF3/RTC_1s/TC0_P[1] | bidirectional | SWD clock multiplexed with GPIO P20, UART1/UART2 RX, CF3, RTC_1S and timer 0 output; SWD pins are pulled up by default after power-up. |
| 36 | SWDIO/P21/TX1/TX2/CF2/TC0_P[0]/RTC_OUT | bidirectional | SWD data multiplexed with GPIO P21, UART1/UART2 TX, CF2, timer 0 output and RTC_OUT; SWD pins are pulled up by default after power-up. |
| 37 | P30/ISPEN/TCI/KEY3/CF4/TC1_P[1]/RTC_OUT | bidirectional | GPIO P30 with 6 mA drive; the BOOTROM samples this pin after reset and enters ISP if it is low, so the application must account for this. |
| 38 | P22/RX2/KEY4/MOSI3/TC1_N[0]/CF4 | bidirectional | GPIO P22 multiplexed with UART2 RX, KEY4, SPI3 MOSI, timer 1 output and CF4. |
| 39 | P23/TX2/KEY5/MISO3/TC1_P[0]/RTC_OUT | bidirectional | GPIO P23 multiplexed with UART2 TX, KEY5, SPI3 MISO, timer 1 output and RTC_OUT. |
| 40 | P24/SCL/TCI/TC1_P[0]/SCSN4/CF4 | bidirectional | GPIO P24 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with I2C SCL, timer input/output, SPI4 chip-select and CF4. |
| 41 | P25/SDA/TCI/TC1_P[1]/SCLK4/RTC_OUT | bidirectional | GPIO P25 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with I2C SDA, timer input/output, SPI4 clock and RTC_OUT. |
| 42 | P26/RX3/TCI/TC1_N[0]/CF2/RTC_OUT/MOSI4 | bidirectional | GPIO P26 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with UART3 RX, timer, CF2, RTC_OUT and SPI4 MOSI. |
| 43 | P27/TX3/TCI/TC1_N[1]/CF3/RTC_1s/MISO4 | bidirectional | GPIO P27 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with UART3 TX, timer, CF3, RTC_1S and SPI4 MISO. |
| 44 | P31/SDO2/MISO0_1/SCL/CF4/RTC_OUT | bidirectional | GPIO P31 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MISO/SDO, I2C SCL, CF4 and RTC_OUT. |
| 45 | P32/SDI2/MOSI0_1/SDA/CF3/RTC_1S | bidirectional | GPIO P32 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI MOSI/SDI, I2C SDA, CF3 and RTC_1S. |
| 46 | P33/SCLK2/SCLK0_1/RX2/CF2/RTC_OUT/RTC_1S | bidirectional | GPIO P33 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI clock, UART2 RX, CF2, RTC_OUT and RTC_1S. |
| 47 | P34/SCSN2/SCSN0_1/TX2/CF1/RTC_OUT/RTC_1S | bidirectional | GPIO P34 with optional pull-up, TTL/CMOS input and open-drain, multiplexed with SPI chip-select, UART2 TX, CF1, RTC_OUT and RTC_1S. |
| 48 | LXO | passive | 32.768 kHz passive crystal output; no external resistor or capacitor is needed (on-chip), and it must be guarded from neighbouring signals by ground. |
| 49 | LXI | passive | 32.768 kHz passive crystal input, paired with LXO; no external resistor or capacitor is needed and it must be guarded by ground. |
| 50 | BVSS | power_in | Ground of the VBAT domain. |
| 51 | LDO_VBAT | power_out | VBAT-domain LDO output; requires an external 0.22 µF capacitor. |
| 52 | VBAT | power_in | 3.6 V battery or supercapacitor input that powers only the RTC; it is also the SAR ADC input (two internal 300 kΩ divider resistors, 0.5× gain), and an RC filter of 10 Ω and 1 µF is recommended. |
| 53 | VREFB | output | SAR ADC internal reference output, typically 1.25 V; requires an external 0.22 µF capacitor. |
| 54 | P40/KEY6/AIN3 | bidirectional | VBAT-domain GPIO P40 with KEY6 and SAR ADC input AIN3, which can measure up to 3.6 V at 0.5× PGA; the input-high level must not exceed VBAT. |
| 55 | P41/KEY7/AIN2 | bidirectional | VBAT-domain GPIO P41 with KEY7 and SAR ADC input AIN2; the input range must not exceed 1.25 V (PGA=1), 2.5 V (PGA=0.5) or the supply (PGA=0.2). |
| 56 | P42/RTCOUT2/AIN1/SCL/KEY6/RTC_1S | bidirectional | VBAT-domain GPIO P42 with RTCOUT, SAR ADC input AIN1 (range as P41), I2C SCL, KEY6 and RTC_1S; it is not recommended to connect a battery here because it drives RTCOUT while VBAT alone is powered. |
| 57 | P43/AIN0/SDA/KEYOUT | bidirectional | VBAT-domain GPIO P43 with SAR ADC input AIN0 (range as P41), I2C SDA and KEYOUT, which is a key-event power control output for external EEPROM. |
| 58 | P50/AIN4/KEY6/RTC_OUT | bidirectional | VBAT-domain GPIO P50 with SAR ADC input AIN4 (range as P41), KEY6 and RTC_OUT. |
| 59 | P51/AIN5/KEYOUT/RTC_1S | bidirectional | VBAT-domain GPIO P51 with SAR ADC input AIN5 (range as P41), KEYOUT and RTC_1S. |
| 60 | UAN | input | Voltage channel A negative fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 61 | UAP | input | Voltage channel A positive fully differential analog input; maximum differential peak is ±1000 mV at PGA=1. |
| 62 | AVSS3 | power_in | Analog ground of the internal voltage reference. |
| 63 | VREFA | output | ADC reference, typically 1.25 V; requires 0.1 µF and 1 µF external capacitors. |
| 64 | LDO3 | power_out | Metering ADC supply LDO, typically 3 V; requires 0.1 µF and 1 µF external capacitors. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENERGY |
| Package | LQFP-64(10x10) |
| Category | ADC/DAC/Data Conversion |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 有功电能测量误差 | Err | -0.1 | | 0.1 | % | 8000:1动态范围 | 30 |
| 无功电能测量误差 | Err | -0.1 | | 0.1 | % | 8000:1动态范围 | 30 |
| 视在电能测量误差 | Err | -0.1 | | 0.1 | % | 8000:1动态范围 | 30 |
| 有效值测量误差 | Err | -0.2 | | 0.2 | % | 2000:1动态范围 | 30 |
| 功率测量误差 | Err | -0.1 | | 0.1 | % | 2000:1动态范围 | 30 |
| 全失压电流测量误差 | | -0.5 | | 0.5 | % | 400:1动态范围 | 30 |
| 最大信号电平(差分, PGA=1) | Vxn | -1000 | | 1000 | mVp | PGA=1,差分信号 | 30 |
| 频率测量范围 | | 40 | | 75 | Hz | | 30 |
| 电能脉冲输出最大频率 | | | | 20 | KHz | 当脉宽低于 84ms 时 | 30 |
| 基准电压输出 | Vref | 1.25 | 1.26 | 1.27 | V | VCC=3V~5.5V,温度范围:-40℃~+85℃ | 30 |
| SAR ADC 输入范围 | SAR-IN | 0 | | | V | 最大值为 BGR(内部低功耗基准,典型值 1.25V) | 30 |
| 低功耗比较器 LVD 阈值 | LVD | 2.3 | | 4.9 | V | LVD 阈值可配置,2.3V 到 4.9V | 30 |
| 低功耗比较器 CMP0 阈值 Vil1 | Vil1 | 1.23 | 1.28 | 1.33 | V | 默认配置下比较器输出低电平的阈值 | 30 |
| 低功耗比较器 CMP0 阈值 Vil2 | Vil2 | 0.8 | 0.84 | 0.88 | V | 选择0.9V档并且选择有迟滞时 | 30 |
| VBAT 测量范围 | VBAT | 0 | 3.6 | 5 | V | SAR ADC 对 VBAT 引脚电压的测量范围 | 30 |
| 输入高频时钟频率范围 | HOSI | 4.096 | 16.384 | 32.768 | Mhz | | 31 |
| 内部PLL时钟频率范围 | PLL | 8.192 | | 16.384 | MHz | fosc=32.768Khz | 31 |
| 内部高频RCH(常温) | RCH | 3 | 3.2 | 3.85 | MHz | 常温,用于芯片复位后默认 | 31 |
| 内部低频RCL | RCL | 20 | 32 | 40 | KHz | 用于WDT时钟 | 32 |
| 主电源 VCC | VCC | 2.4 | | 5.5 | V | 建议主电源选择为3.3V±5%或者5V±5% | 32 |
| CPU 最低工作电压 | Vil | 1.8 | 1.9 | 2 | V | 全温度范围 | 32 |
| VBAT 供电电压 VBAT1 | VBAT1 | 2.5 | 3.6 | 5.5 | V | RTC 温补电路正常工作,RTC 精度保证的电压工作范围 | 32 |
| VBAT 供电电压 VBAT2 | VBAT2 | 1.8 | 3.6 | 5.5 | V | RTC 万年历翻转正常,温补电路不保证 | 32 |
| VBAT 供电功耗(典型) | SIdd | | 1.5 | | μA | 典型条件:Vbat=3.6V;Tc=25度 | 32 |
| VBAT 供电功耗(极限) | SIdd | | | 2 | μA | 极限条件:Vbat=3.6V;Tc=85度 | 32 |
| LDO18 内核电压 | V1P8 | 1.62 | 1.8 | 1.98 | V | CPU 内核电压 | 32 |
| LDO3 Σ-ΔADC 电压 | V3 | 2.85 | 2.9 | 2.95 | V | Σ-ΔADC 电压 | 32 |
| LDO_VBAT VBAT域数字电压 | V2 | 1.9 | 2 | 2.2 | V | VBAT 域数字电压 | 32 |
| 主电电压 | Vvcc | -0.3 | | 7 | V | | 32 |
| 电池输入电压 | Vvbat | -0.3 | | 7 | V | | 32 |
| DVDD to DGND | | -0.3 | | 7 | V | | 32 |
| DVDD to AVDD | | -0.3 | | 0.3 | V | | 32 |
| 电流输入引脚电压 | IAP,IAN,IBP,IBN,ICP,ICN,INP,INN | -6 | | 6 | V | | 32 |
| 电压输入引脚电压 | VAP,VAN,VBP,VBN,VCP,VCN | -6 | | 6 | V | | 32 |
| 数字IO输出低电平 | VOL | -0.3 | | | V | | 33 |
| 模拟输入电压(相对AGND) | VINA | -0.3 | | | V | 相对于 AGND;上限为 AVDD+0.3(表中为表达式) | 33 |
| 工作温度范围 | TA | -40 | | 85 | ℃ | | 33 |
| 存储温度范围 | Tstg | -65 | | 150 | ℃ | | 33 |
| ESD 人体模型 HBM | ESD | | | 4000 | V | HBM,JEDEC EIA/JESD22-A114,所有引脚 | 33 |
| ESD 机械模型 MM | ESD | | | 200 | V | MM,JEDEC EIA/JESD22-A115C,所有引脚 | 33 |
| ESD 充电器件模型 CDM | ESD | | | 500 | V | CDM,JEDEC EIA/JESD22-C101F,所有引脚 | 33 |
| 闩锁试验 Latch-up | LatchUp | | | 200 | mA | JEDEC STANDARD NO.78D NOVEMBER 2011,所有引脚 | 33 |
## CAD (KiCad official)
- Symbol: `RN2025`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `rn2025-etched.step` / `rn2025-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `rn2025.step` / `rn2025.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [RENERGY datasheet](docs/rn2025-datasheet.pdf) (301 pp, sha256 `bae190d83688b304`, retrieved 2026-11-13, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/rn2025-datasheet.pdf)