Generated by kicad-footprint-generator · KiCad file format 20260206
RFX2411
Skyworks Solutions · RF Chips · WQFN-20-EP(3x3)
RFX2411 from Skyworks Solutions, in a WQFN-20-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground that must be connected to ground in the application circuit. |
| 2 | N/C | unconnected | No internal connection. |
| 3 | DNC | unconnected | Reserved; do not connect in the application circuit. |
| 4 | N/C | unconnected | No internal connection. |
| 5 | TXRX | passive | RF signal to/from the transceiver; DC shorted to GND. |
| 6 | TXEN | input | CMOS input controlling TX enable; a logic 1 requires more than 1.2 V and a logic 0 requires less than 0.3 V. |
| 7 | RXEN | input | CMOS input controlling RX enable; a logic 1 requires more than 1.2 V and a logic 0 requires less than 0.3 V. |
| 8 | PDET | output | Analog voltage proportional to the PA power output, measured as 0.14 V at POUT = +5 dBm and 0.9 V at POUT = +20 dBm into a 10 kΩ load. |
| 9 | MODE | input | CMOS input controlling the mode of operation; a logic 1 requires more than 1.2 V and a logic 0 requires less than 0.3 V. |
| 10 | SWant | input | CMOS input selecting the antenna for diversity (1 enables ANTA, 0 enables ANTB). |
| 11 | GND | power_in | Ground that must be connected to ground in the application circuit. |
| 12 | ANTB | passive | RF signal from the PA or RF signal applied to the LNA; DC shorted to ground. |
| 13 | GND | power_in | Ground that must be connected to ground in the application circuit. |
| 14 | ANTA | passive | RF signal from the PA or RF signal applied to the LNA; DC shorted to ground. |
| 15 | IND | passive | Inductor connected to GND. |
| 16 | DNC | unconnected | Reserved; do not connect in the application circuit. |
| 17 | DNC | unconnected | Reserved; do not connect in the application circuit. |
| 18 | VDD1 | power_in | Voltage supply connection; 2.0 V to 3.6 V (3.3 V typical), and must be continuously applied to all VDD pins. |
| 19 | GND | power_in | Ground that must be connected to ground in the application circuit. |
| 20 | VDD2 | power_in | Voltage supply connection; 2.0 V to 3.6 V (3.3 V typical), and must be continuously applied to all VDD pins. |
| 21 | GND | power_in | Ground that must be connected to ground in the application circuit; per Figure 5 the center pad is GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Skyworks Solutions |
| Package | WQFN-20-EP(3x3) |
| Category | RF & Radio |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| DC VDD voltage supply | VDD | 0 | 4 | V | All VDD pins | 3 | |
| DC control pin voltage | 0 | 3.6 | V | Through 1 kΩ resistor | 3 | ||
| DC VDD current consumption | 350 | mA | Through VDD pins when TX is ON | 3 | |||
| TX RF input power | 5 | dBm | 3 | ||||
| ANT RF RX input power | 5 | dBm | LNA mode | 3 | |||
| ANT RF RX input power | 16 | dBm | Bypass mode | 3 | |||
| Junction temperature | 150 | °C | 3 | ||||
| Storage ambient temperature | -50 | 150 | °C | No RF and DC voltages applied | 3 | ||
| ESD Human Body Model (HBM) | 1000 | V | Human Body Model (HBM) | 3 | |||
| DC VDD voltage supply | VDD | 2 | 3.3 | 3.6 | V | All VDD pins | 3 |
| Control voltage high | 1.2 | V | RXEN, TXEN, and MODE pins | 3 | |||
| Control voltage low | 0 | 0.3 | V | RXEN, TXEN, and MODE pins | 3 | ||
| DC control pin current consumption | 1 | μA | See note 2 | 3 | |||
| DC shutdown current | 300 | nA | 3 | ||||
| PA turn-on/turn-off time | 1 | μsec | 3 | ||||
| LNA turn-on/turn-off time | 1 | μsec | 3 | ||||
| Antenna switch time | 1 | μsec | 3 | ||||
| Operating ambient temperature | -40 | 125 | °C | 3 | |||
| Operating frequency band (transmit mode) | 2.4 | 2.5 | GHz | All RF pins terminated by 50 Ω | 4 | ||
| Operating frequency band (receive mode) | 2.4 | 2.5 | GHz | All RF pins are loaded by 50 Ω | 4 | ||
| Operating frequency (bypass mode) | 2.4 | 2.5 | GHz | 4 | |||
| Input P1dB (bypass mode) | 16 | dBm | At ANTA or ANTB | 4 | |||
| Thermal resistance, junction-to-ambient | ja | 35 | °C/W | See note 2 | 3 | ||
| Saturated output power | 21 | dBm | 4 | ||||
| Output P1dB | 19 | dBm | CW input | 4 | |||
| Small signal gain | 26 | dB | High Idq TX mode | 4 | |||
| Small signal gain | 24 | dB | Low Idq TX mode | 4 | |||
| Second harmonic | -35 | dBc | POUT ≤ +20 dBm, CW at ANT pin | 4 | |||
| Third harmonic | -35 | dBc | POUT ≤ +20 dBm, CW at ANT pin | 4 | |||
| Total supply current | 95 | mA | POUT = +20 dBm, High Idq TX mode | 4 | |||
| TX quiescent current | 18 | mA | High Idq TX mode | 4 | |||
| TX quiescent current | 15 | mA | Low Idq TX mode | 4 | |||
| Input return loss (transmit mode) | -15 | dB | 4 | ||||
| Output return loss | -7 | dB | 4 | ||||
| Power detector voltage | 0.14 | V | POUT = +5 dBm, 10 kΩ load | 4 | |||
| Power detector voltage | 0.9 | V | POUT = +20 dBm, 10 kΩ load | 4 | |||
| Gain | 14 | dB | Low noise figure mode | 4 | |||
| Gain | 10 | dB | Low current mode | 4 | |||
| Noise figure | 2.5 | dB | Low noise figure mode | 4 | |||
| Noise figure | 3.5 | dB | Low current mode | 4 | |||
| Input P1dB | -8 | dBm | Low noise figure mode | 4 | |||
| Input P1dB | -3 | dBm | Low current mode | 4 | |||
| RX quiescent current | 9 | mA | Low noise figure mode | 4 | |||
| Input return loss (receive mode) | -8 | dB | At ANT pin, low NF mode | 4 | |||
| Input return loss (receive mode) | -12 | dB | At TXRX pin, low NF mode | 4 | |||
| Insertion loss | 5 | dB | 4 | ||||
| Current consumption (bypass mode) | 700 | nA | Through VDD supply pins | 4 |
CAD (KiCad official)
- Symbol:
RFX2411 - Footprint:
Package_DFN_QFN:QFN-20-1EP_3x3mm_P0.4mm_EP1.65x1.65mm - 3D model: WQFN-20-EP(3x3), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
rfx2411-etched.step/rfx2411-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rfx2411.step/rfx2411.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Skyworks Solutions datasheet (9 pp, sha256
adffe6a9cdc9d702, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).