3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownREF3450QDBVRQ1
Texas Instruments · Voltage Reference · SOT-23-6
REF3450QDBVRQ1 from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND_F | power_in | Ground force connection (接地强制连接) for the reference, intended to be used with GND_S as a Kelvin pair to minimize IR-drop error. |
| 2 | GND_S | power_in | Ground sense connection (接地检测连接) on a high-impedance line that is paired with GND_F for accurate ground reference. |
| 3 | EN | input | Enable input: pulling EN to 0.5 V or lower puts the device into shutdown, 1.6 V or higher enables operation, and EN must not be driven above VIN (absolute maximum IN + 0.3 V). |
| 4 | IN | power_in | Input supply voltage connection; recommended range is VOUT + VDO to 12 V, with an absolute maximum of 13 V. |
| 5 | OUT_S | output | Reference voltage output sense connection (基准电压输出检测连接) on a high-impedance line for Kelvin sensing; absolute maximum voltage on the output pins is 5.5 V. |
| 6 | OUT_F | output | Reference voltage output force connection (基准电压输出强制连接) for the 5.0 V REF3450 output, rated for ±10 mA load current with a 20 mA output short-circuit limit. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-23-6 |
| Category | Power Management (PMIC) |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output voltage accuracy | -0.05 | 0.05 | % | TA = 25°C | 6 | ||
| Output voltage temperature coefficient | 2.5 | 6 | ppm/℃ | 6 | |||
| Line regulation | ΔVO/ΔVIN | 2 | 15 | ppm/V | VIN = VOUT + VDO (2) to 12V | 6 | |
| Load regulation, sourcing | ΔVO/ΔIL | 20 | 30 | ppm/mA | IL = 0mA to 10mA, VIN = VOUT + VDO (3) | 6 | |
| Load regulation, sinking (REF3450-Q1) | ΔVO/ΔIL | 70 | 140 | ppm/mA | IL = 0mA to -10mA, VIN = VOUT + VDO (3) | 6 | |
| Capacitive load, stable output capacitor range | CL | 0.1 | 10 | µF | 6 | ||
| Input voltage, absolute maximum | IN | -0.3 | 13 | V | 5 | ||
| Enable pin voltage, absolute maximum | EN | -0.3 | V | Printed upper limit is IN + 0.3 V | 5 | ||
| Output voltage, absolute maximum | VOUT | -0.3 | 5.5 | V | 5 | ||
| Operating temperature range, absolute maximum | TA | -55 | 150 | °C | Natural convection | 5 | |
| Storage temperature range | Tstg | -65 | 170 | °C | 5 | ||
| Output short-circuit current, absolute maximum | 20 | mA | 5 | ||||
| Input voltage, recommended | IN | 12 | V | Printed minimum is VOUT + VDO | 5 | ||
| Enable voltage, recommended | EN | 0 | V | Printed maximum is IN | 5 | ||
| Output current, recommended | IL | -10 | 10 | mA | 5 | ||
| Operating ambient temperature, recommended | TA | -40 | 25 | 125 | °C | 5 | |
| Input voltage | VIN | 12 | V | Printed minimum is VOUT + VDO | 7 | ||
| Output current capability | IL | -10 | 10 | mA | VIN = VOUT + VDO to 12V | 7 | |
| Quiescent current, operating mode | IQ | 72 | 95 | µA | 工作模式 | 7 | |
| Quiescent current, shutdown mode | IQ | 2.5 | 3 | µA | 关断模式 | 7 | |
| Dropout voltage | VDO | 50 | 100 | mV | IL = 0mA | 7 | |
| Dropout voltage | VDO | 500 | mV | IL = 10mA | 7 | ||
| Enable pin voltage for reference on (EN = 1) | VEN | 1.6 | V | 工作模式下的电压基准 (EN = 1) | 7 | ||
| Enable pin voltage for reference off (EN = 0) | VEN | 0.5 | V | 关断模式下的电压基准 (EN = 0) | 7 | ||
| Enable pin leakage current | IEN | 1 | 2 | µA | VEN = VIN = 12V | 7 | |
| Short-circuit current | ISC | 18 | 22 | mA | TA = 25°C, VOUT = 0V | 7 | |
| ESD, human body model (HBM) | V(ESD) | -2500 | 2500 | V | AEC Q100-002 | 5 | |
| ESD, charged device model (CDM) | V(ESD) | -1500 | 1500 | V | AEC Q100-011 | 5 | |
| Output voltage | VOUT | 5 | V | REF3450-Q1 | 7 | ||
| Low-frequency noise, peak-to-peak (REF3450-Q1) | enp-p | 3.8 | µV p-p/V | 0.1Hz ≤ f ≤ 10Hz | 6 | ||
| Integrated broadband noise | en | 24 | µVrms | 10Hz ≤ f ≤ 10kHz | 6 | ||
| Output voltage noise density (REF3450-Q1) | en | 0.2 | ppm/√Hz | f = 1kHz (REF3440-Q1 and REF3450-Q1) | 6 | ||
| Long-term stability, DBV package, 0h to 1000h | 25 | ppm | 35°C, 0h to 1000h | 6 | |||
| Long-term stability, DBV package, 1000h to 2000h | 10 | ppm | 35°C, 1000h to 2000h | 6 | |||
| Output voltage thermal hysteresis, DBV package, cycle 1 | 30 | ppm | 25°C, -40°C, 125°C, 25°C cycle 1 | 6 | |||
| Output voltage thermal hysteresis, DBV package, cycle 2 | 10 | ppm | 25°C, -40°C, 125°C, 25°C cycle 2 | 6 | |||
| Junction-to-ambient thermal resistance (DBV 6-pin) | RθJA | 122.6 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance (DBV 6-pin) | RθJC(top) | 80.2 | °C/W | 5 | |||
| Junction-to-board thermal resistance (DBV 6-pin) | RθJB | 42 | °C/W | 5 | |||
| Junction-to-top characterization parameter (DBV 6-pin) | ΨJT | 23.2 | °C/W | 5 | |||
| Junction-to-board characterization parameter (DBV 6-pin) | ΨJB | 41.9 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
REF3450QDBVRQ1 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ref3450qdbvrq1-etched.step/ref3450qdbvrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ref3450qdbvrq1.step/ref3450qdbvrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
addb0b3508cd0c2e, retrieved 2026-11-11, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).