main
Ray Publish 0.1.0 3850b85

RE46C141SW16TF

Microchip Tech · Specialized Sensors · SOIC-16-300mil

RE46C141SW16TF from Microchip Tech, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 C1 passive The capacitor on this pin sets the high photo-amplifier gain used for push-to-test and chamber sensitivity test, with A = 1 + (C1/10) where C1 is in pF, and the gain should be <10000.
2 C2 passive The capacitor on this pin sets the normal photo-amplifier gain during standby, with A = 1 + (C2/10) where C2 is in pF.
3 DETECT input Positive input to the photo amplifier, normally connected to the cathode of an external photodiode operated at zero bias.
4 STROBE output Regulated output voltage of VDD-5 that is active during a smoke test and forms the negative side of the photo amplifier circuitry.
5 VDD power_in Connect to the positive supply voltage.
6 IRED output Provides a regulated pulsed output voltage pre-driver for the infrared emitter, usually driving the base of an NPN transistor.
7 IO bidirectional Bidirectional pin that allows many detectors to be interconnected in a single system and has an internal pull-down device.
8 HORNB output Connected to the metal electrode of a piezoelectric transducer.
9 HORNS output Complementary output to HORNB that connects to the ceramic electrode of the piezoelectric transducer.
10 FEED input Usually connected to the feedback electrode through a current limiting resistor; if not used, this pin must be connected to VDD or VSS.
11 LED output Open-drain NMOS output used to drive a visible LED.
12 COSC passive A capacitor connected to this pin with a parallel resistor sets the internal clock low time, which is approximately the clock period.
13 ROSC passive A resistor between this pin and COSC (pin 12) sets the internal clock high time and also sets the IRED pulse width (100-200 uS).
14 VSS power_in Connect to the negative supply voltage.
15 LBSET input Input connected to a VDD reference voltage to set the low battery warning voltage.
16 TEST input Input used to invoke two test modes; it has an internal pull-down.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-16-300mil
Category Sensors
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VDD 12.5 V 1
Input Voltage Range Except FEED Vin -0.3 V Except FEED; upper limit printed as Vdd +.3 V 1
FEED Input Voltage Range Vinfd -10 22 V 1
IO Input Voltage Range Vio1 -0.3 17 V 1
Input Current except FEED Iin 10 mA 1
Operating Temperature TA -25 75 °C 1
Storage Temperature TSTG -55 125 °C 1
Maximum Junction Temperature TJ 150 °C 1
Supply Voltage VDD 6 12 V Operating, pin 5 2
Supply Current IDD1 4 6 uA Configured as in Figure 2, COSC=VSS 2
Supply Current IDD2 5.5 8 uA Configured as in Figure 2, VDD=12V, COSC=VSS 2
Supply Current IDD3 2 mA Configured as in Figure 2, STROBE on, IRED off, VDD=12V 2
Supply Current IDD4 3 mA Configured as in Figure 2, STROBE on, IRED on, VDD=12V, Note 1 2
Input Voltage High FEED VIH1 4.5 6.2 V 2
Input Voltage High IO VIH2 3.2 V No Local Alarm, IO as an Input 2
Input Voltage High TEST VIH4 8.5 V 2
Input Voltage Low FEED VIL1 2.7 4.5 V 2
Input Voltage Low IO VIL2 1.5 V No Local Alarm, IO as an Input 2
Input Voltage Low TEST VIL4 7 V 2
Input Leakage Low pin 16 IIL3 -1 uA VDD=12V, Vin=VSS 2
Input Leakage Low FEED ILFD -50 uA FEED=-10V 2
Input Leakage High FEED IHFD 50 uA FEED=22V 2
Input Pull Down Current pin 16 IPD1 0.25 10 uA Vin=VDD 2
Input Pull Down Current pin 7 IPDIO1 20 80 uA Vin=VDD 2
Output Leakage Current Low IOZL1 -1 uA Output Off, Output=VSS 2
Output Leakage Current High IOZH1 1 uA Output Off, Output=VDD 2
Output Voltage Low VOL1 1 V Iol=16mA, VDD=6.5V 3
Output Voltage Low VOL2 0.5 V Iol=5mA, VDD=6.5V 3
Output Voltage Low VOL3 0.6 V Iol=10mA, VDD=6.5V 3
Output Voltage High VOH1 5.5 V Ioh=-16mA, VDD=6.5V 3
I Output Current IOH1 -16 -4 mA Alarm, Vio=Vdd-2V or Vio=0V 3
IO Discharge Current IIODMP 5 mA At Conclusion of Local Alarm or Test, Vio=1V 3
Low Battery Alarm Voltage VLB 6.9 7.2 7.5 V R14=100K, R15=47K 3
Output Voltage STROBE off VSTOF -0.1 V STROBE off, VDD=12V, Iout=-1uA; limit printed as VDD - .1 3
Output Voltage STROBE on VSTON -5.3 -5 -4.7 V STROBE on, VDD=9V, Iout= 100uA to 500uA; limits printed as VDD - 5.3, VDD - 5, VDD - 4.7 3
Output Voltage IRED off VIREDOF 0.1 V IRED off, VDD=12V, Iout=1uA 3
Output Voltage IRED on VIREDON 2.25 3.1 3.75 V IRED on, VDD=9V, Iout=0 to -6mA, Ta=25C 3
Common Mode Voltage VCM1 0.5 V Local smoke, Push to Test or Chamber Test, Note 1; upper limit printed as VDD-2 3
Smoke Comparator Reference, Internal Reference Vref -3.85 -3.15 V limits printed as VDD-3.85 and VDD-3.15 3
Oscillator Period TPOSC 7.1 7.9 8.6 mS No Alarm Condition, Note 2 4
LED and STROBE On Time TON1 7.1 7.9 8.6 mS Operating 4
LED Period Standby TPLED1 28.8 32.4 35.2 S Standby, No Alarm 4
LED Period Local Alarm TPLED2 0.45 0.5 0.55 S Local Alarm Condition 4
STROBE and IRED Pulse Period Standby TPER1 7.3 8.1 8.8 S Standby, No Alarm 4
STROBE and IRED Pulse Period After 1 Sample TPER1A 1.8 2 2.2 S Standby, After 1 Valid Smoke Sample 4
STROBE and IRED Pulse Period After 2 Samples TPER1B 0.9 1 1.1 S Standby, After 2 Consecutive Valid Smoke Samples 4
STROBE and IRED Pulse Period Local Alarm TPER2 0.9 1 1.1 S In Local Alarm, (3 Consecutive Valid Smoke Samples) 4
STROBE and IRED Pulse Period Chamber or Low Battery Test TPER5 28.8 35.2 S Chamber Test or Low Battery Test, no Alarms 4
IRED On Time TON2 94 104 115 uS Operating, Note 2 4
Horn On Time THON1 450 500 550 mS Operating, Alarm Condition, Note 1 4
Horn On Time Low Battery or Failed Chamber Test THON2 7.1 7.9 8.6 mS Low Battery or Failed Chamber Test, No Alarm 4
Horn Off Time THOF1 450 500 550 mS Operating, Alarm Condition, Note 1 4
Horn Off Time Alarm THOF2 1.35 1.5 1.65 S Operating, Alarm Condition, Note 1 4
Horn Off Time Low Battery or Failed Chamber Test THOF3 28.8 32.4 35.2 S Low Battery or Failed Chamber Test, No Alarm 4
IO Charge Dump Duration TIODMP 0.68 1.1 S At Conclusion of Local Alarm or Test 4
IO Filter TIOFILT 450 mS IO pulse width guaranteed to be filtered. IO as Input, No Local Alarm 4
Remote Alarm Delay TIODLY2 0.9 1.65 S No Local Alarm, From IO Active Horn Active 4
Temperature Coefficient STROBE Output Voltage TCST 0.01 %/ºC VDD=6V to 12V, STROBE Output Voltage 3
Temperature Coefficient IRED Output Voltage TCIRED 0.3 %/ºC VDD=6V to 12V, IRED Output Voltage 3

CAD (KiCad official)

  • Symbol: RE46C141SW16TF
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: re46c141sw16tf-etched.step / re46c141sw16tf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); re46c141sw16tf.step / re46c141sw16tf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet, copy hosted by LCSC (12 pp, sha256 adf2921c8e518841, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF