main
Ray
Publish 0.1.0
86bfc89
RAA214023GNP#HC0
RENESAS · Linear Voltage Regulators (LDO) · QFN-20(5x5)
RAA214023GNP#HC0 from RENESAS, in a QFN-20(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | power_out | Output pin supplying power to the load; a minimum 22µF capacitor is required from VOUT to GND for stable operation. |
| 2 | SNS | input | Output voltage sense pin; connect to VOUT when the Voltage Set pins are used, otherwise float it if external feedback resistors are used. |
| 3 | FB | input | Voltage feedback pin internally set to 0.8V (±1.75%) by the band gap; the divider around it sets the LDO output voltage. |
| 4 | PG | tri_state | Open-drain power-good output that is open when VOUT is within 90% to 110% of target and pulls low outside this range; use a 10kΩ-100kΩ pull-up or leave floating if unused. |
| 5 | 50mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 50mV. |
| 6 | 100mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 100mV. |
| 7 | 200mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 200mV. |
| 8 | GND | power_in | Ground pin that must be tied to ground. |
| 9 | 400mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 400mV. |
| 10 | 800mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 800mV. |
| 11 | 1.6V | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 1.6V. |
| 12 | NC | unconnected | No connection; float this pin. |
| 13 | CSET | passive | Noise reduction pin; connect a 1µF capacitor to ground close to the device, and larger values increase start-up time. |
| 14 | EN | input | Enable pin, low disables and high enables the LDO; must not be left floating, tie to VIN for automatic enabling. |
| 15 | VIN | power_in | Input voltage pin supplying the regulator (2.7V to 5.5V) and requiring a minimum 10µF ceramic input bypass capacitor. |
| 16 | VIN | power_in | Input voltage pin supplying the regulator (2.7V to 5.5V) and requiring a minimum 10µF ceramic input bypass capacitor. |
| 17 | VIN | power_in | Input voltage pin supplying the regulator (2.7V to 5.5V) and requiring a minimum 10µF ceramic input bypass capacitor. |
| 18 | GND | power_in | Ground pin that must be tied to ground. |
| 19 | VOUT | power_out | Output pin supplying power to the load; a minimum 22µF capacitor is required from VOUT to GND for stable operation. |
| 20 | VOUT | power_out | Output pin supplying power to the load; a minimum 22µF capacitor is required from VOUT to GND for stable operation. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | QFN-20(5x5) |
| Category | Power Supply Chip |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | VIN | 2.7 | 5.5 | V | 7 | ||
| Input Supply UVLO | VIN_UVLO | 2.2 | 2.3 | 2.45 | V | VIN UVLO rising | 7 |
| Input Supply UVLO Hysteresis | VIN_UVLO_HYS | 0.03 | 0.23 | 0.3 | V | VIN UVLO Hysteresis | 7 |
| Output Current | IOUT | 2 | A | 7 | |||
| VIN Quiescent Current | IQ (VIN) | 50 | 195 | 300 | µA | VOUT = 3.3V, VIN = 5V | 7 |
| Ground Pin Current in Shutdown | ISHDN | 200 | nA | VEN = 0V, TJ = +125°C | 7 | ||
| Output Voltage Range | 0.8 | V | VIN = 2.7V to 5.5V (max VIN - VDO) | 7 | |||
| FB voltage | 0.786 | 0.8 | 0.814 | V | 7 | ||
| Output Voltage Accuracy (initial) | -1.5 | 1.5 | % | Initial at IOUT = 10mA, TJ = 25°C | 7 | ||
| Output Voltage Accuracy | -1.75 | 1.75 | % | Initial at IOUT = 10mA to 2A | 7 | ||
| Line Regulation | 0.1 | %/V | VIN = 2.7V to 5.5V, IOUT = 5mA | 7 | |||
| Load Regulation | 0.03 | %/A | IOUT = 10mA to 2A | 7 | |||
| Dropout Voltage | VDO | 420 | 570 | mV | VIN = 3.3V, IOUT = 2A | 7 | |
| Internal Current Limit | 3.3 | A | VIN = 2.7V to 5.5V, VOUT = 0V. | 7 | |||
| Start-Up Time | 200 | µs | VIN = 5.5V, VOUT = 1.8V, IOUT = 2A, CSET = 1µF | 7 | |||
| Thermal Shutdown | 155 | °C | Rising | 7 | |||
| Thermal Shutdown Hysteresis | 10 | °C | 7 | ||||
| Output RMS Noise | 6.5 | µVRMS | ILOAD = 2A, Frequency = 10Hz to 100kHz, COUT = 22μF, CSET = 1μF VOUT = 3.3V | 7 | |||
| Supply Voltage | VIN | 2.7 | 5.5 | V | 6 | ||
| Ambient Temperature | -40 | 125 | °C | 6 | |||
| Output Voltage | 0.8 | V | max is VIN - VDO | 6 | |||
| VIN, VOUT absolute maximum | 6.5 | V | VIN, VOUT | 6 | |||
| Pin voltage absolute maximum | 6.5 | V | SNS, FB, PG, 50mV, 100mV, 200mV, 400mV, 800mV, 1.6V, CSET, EN | 6 | |||
| Maximum Junction Temperature | 150 | °C | 6 | ||||
| Storage Temperature Range | -65 | 150 | °C | 6 | |||
| ESD Human Body Model | 3 | kV | Tested per JS-001-2017 | 6 | |||
| ESD Charged Device Model | 1.25 | kV | Tested per JS-002-2018 | 6 | |||
| Latch-Up | 100 | mA | Tested per JESD78E; Class 2, Level A | 6 | |||
| Thermal Resistance Junction-Ambient | θJA | 39 | °C/W | 20 Ld 5 × 5 QFN Package | 6 | ||
| Thermal Resistance Junction-Case | θJC | 10 | °C/W | 20 Ld 5 × 5 QFN Package | 6 |
CAD (KiCad official)
- Symbol:
RAA214023GNP#HC0 - Footprint:
Package_DFN_QFN:QFN-20-1EP_5x5mm_P0.65mm_EP3.35x3.35mm - 3D model: QFN-20(5x5) (KiCad packages3D, STEP)
- 3D model files:
raa214023gnp-hc0-etched.step/raa214023gnp-hc0-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);raa214023gnp-hc0.step/raa214023gnp-hc0.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (45 pp, sha256
24afeeb3f892c331, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# RAA214023GNP#HC0
**RENESAS** · Linear Voltage Regulators (LDO) · QFN-20(5x5)
RAA214023GNP#HC0 from RENESAS, in a QFN-20(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | power_out | Output pin supplying power to the load; a minimum 22µF capacitor is required from VOUT to GND for stable operation. |
| 2 | SNS | input | Output voltage sense pin; connect to VOUT when the Voltage Set pins are used, otherwise float it if external feedback resistors are used. |
| 3 | FB | input | Voltage feedback pin internally set to 0.8V (±1.75%) by the band gap; the divider around it sets the LDO output voltage. |
| 4 | PG | tri_state | Open-drain power-good output that is open when VOUT is within 90% to 110% of target and pulls low outside this range; use a 10kΩ-100kΩ pull-up or leave floating if unused. |
| 5 | 50mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 50mV. |
| 6 | 100mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 100mV. |
| 7 | 200mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 200mV. |
| 8 | GND | power_in | Ground pin that must be tied to ground. |
| 9 | 400mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 400mV. |
| 10 | 800mV | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 800mV. |
| 11 | 1.6V | passive | Voltage Set pin that can be grounded or left floating; grounding it increases the output voltage by 1.6V. |
| 12 | NC | unconnected | No connection; float this pin. |
| 13 | CSET | passive | Noise reduction pin; connect a 1µF capacitor to ground close to the device, and larger values increase start-up time. |
| 14 | EN | input | Enable pin, low disables and high enables the LDO; must not be left floating, tie to VIN for automatic enabling. |
| 15 | VIN | power_in | Input voltage pin supplying the regulator (2.7V to 5.5V) and requiring a minimum 10µF ceramic input bypass capacitor. |
| 16 | VIN | power_in | Input voltage pin supplying the regulator (2.7V to 5.5V) and requiring a minimum 10µF ceramic input bypass capacitor. |
| 17 | VIN | power_in | Input voltage pin supplying the regulator (2.7V to 5.5V) and requiring a minimum 10µF ceramic input bypass capacitor. |
| 18 | GND | power_in | Ground pin that must be tied to ground. |
| 19 | VOUT | power_out | Output pin supplying power to the load; a minimum 22µF capacitor is required from VOUT to GND for stable operation. |
| 20 | VOUT | power_out | Output pin supplying power to the load; a minimum 22µF capacitor is required from VOUT to GND for stable operation. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | QFN-20(5x5) |
| Category | Power Supply Chip |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | VIN | 2.7 | | 5.5 | V | | 7 |
| Input Supply UVLO | VIN_UVLO | 2.2 | 2.3 | 2.45 | V | VIN UVLO rising | 7 |
| Input Supply UVLO Hysteresis | VIN_UVLO_HYS | 0.03 | 0.23 | 0.3 | V | VIN UVLO Hysteresis | 7 |
| Output Current | IOUT | | | 2 | A | | 7 |
| VIN Quiescent Current | IQ (VIN) | 50 | 195 | 300 | µA | VOUT = 3.3V, VIN = 5V | 7 |
| Ground Pin Current in Shutdown | ISHDN | | | 200 | nA | VEN = 0V, TJ = +125°C | 7 |
| Output Voltage Range | | 0.8 | | | V | VIN = 2.7V to 5.5V (max VIN - VDO) | 7 |
| FB voltage | | 0.786 | 0.8 | 0.814 | V | | 7 |
| Output Voltage Accuracy (initial) | | -1.5 | | 1.5 | % | Initial at IOUT = 10mA, TJ = 25°C | 7 |
| Output Voltage Accuracy | | -1.75 | | 1.75 | % | Initial at IOUT = 10mA to 2A | 7 |
| Line Regulation | | | 0.1 | | %/V | VIN = 2.7V to 5.5V, IOUT = 5mA | 7 |
| Load Regulation | | | 0.03 | | %/A | IOUT = 10mA to 2A | 7 |
| Dropout Voltage | VDO | | 420 | 570 | mV | VIN = 3.3V, IOUT = 2A | 7 |
| Internal Current Limit | | | 3.3 | | A | VIN = 2.7V to 5.5V, VOUT = 0V. | 7 |
| Start-Up Time | | | 200 | | µs | VIN = 5.5V, VOUT = 1.8V, IOUT = 2A, CSET = 1µF | 7 |
| Thermal Shutdown | | | 155 | | °C | Rising | 7 |
| Thermal Shutdown Hysteresis | | | 10 | | °C | | 7 |
| Output RMS Noise | | | 6.5 | | µVRMS | ILOAD = 2A, Frequency = 10Hz to 100kHz, COUT = 22μF, CSET = 1μF VOUT = 3.3V | 7 |
| Supply Voltage | VIN | 2.7 | | 5.5 | V | | 6 |
| Ambient Temperature | | -40 | | 125 | °C | | 6 |
| Output Voltage | | 0.8 | | | V | max is VIN - VDO | 6 |
| VIN, VOUT absolute maximum | | | | 6.5 | V | VIN, VOUT | 6 |
| Pin voltage absolute maximum | | | | 6.5 | V | SNS, FB, PG, 50mV, 100mV, 200mV, 400mV, 800mV, 1.6V, CSET, EN | 6 |
| Maximum Junction Temperature | | | | 150 | °C | | 6 |
| Storage Temperature Range | | -65 | | 150 | °C | | 6 |
| ESD Human Body Model | | | 3 | | kV | Tested per JS-001-2017 | 6 |
| ESD Charged Device Model | | | 1.25 | | kV | Tested per JS-002-2018 | 6 |
| Latch-Up | | | 100 | | mA | Tested per JESD78E; Class 2, Level A | 6 |
| Thermal Resistance Junction-Ambient | θJA | | 39 | | °C/W | 20 Ld 5 × 5 QFN Package | 6 |
| Thermal Resistance Junction-Case | θJC | | 10 | | °C/W | 20 Ld 5 × 5 QFN Package | 6 |
## CAD (KiCad official)
- Symbol: `RAA214023GNP#HC0`
- Footprint: `Package_DFN_QFN:QFN-20-1EP_5x5mm_P0.65mm_EP3.35x3.35mm`
- 3D model: QFN-20(5x5) (KiCad packages3D, STEP)
- 3D model files: `raa214023gnp-hc0-etched.step` / `raa214023gnp-hc0-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `raa214023gnp-hc0.step` / `raa214023gnp-hc0.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [RENESAS datasheet](docs/raa214023gnp-hc0-datasheet.pdf) (45 pp, sha256 `24afeeb3f892c331`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/raa214023gnp-hc0-datasheet.pdf)