3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownR5F5651CDDFP#10
RENESAS · Pre-ordered MCUs · LQFP-100(14x14)
R5F5651CDDFP#10 from RENESAS, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVCC1 | power_in | Analog supply and reference voltage for the 12-bit A/D converter unit 1, D/A converter and temperature sensor; connect to a branch of VCC and to AVSS1 via a 0.1-μF ceramic capacitor. |
| 2 | EMLE | input | On-chip emulator enable input; drive high when the on-chip emulator is used and low when not used. |
| 3 | AVSS1 | power_in | Analog ground for the 12-bit A/D converter unit 1, D/A converter and temperature sensor; connect to a branch of VSS. |
| 4 | PJ3 | bidirectional | General I/O port PJ3 with alternate functions EDACK1, MTIOC3C, ET0_EXOUT, CTS6#/RTS6#/SS6#, CTS0#/RTS0#/SS0#. |
| 5 | VCL | passive | Internal power supply stabilization pin; connect to VSS via a 0.22-μF multilayer ceramic capacitor placed close to the pin. |
| 6 | VBATT | power_in | Backup power supply pin. |
| 7 | MD/FINED | bidirectional | Operating mode setting input (level must not change during operation) shared with the FINE debug interface I/O. |
| 8 | XCIN | input | Sub-clock oscillator input; connect a crystal resonator between XCOUT and XCIN. |
| 9 | XCOUT | output | Sub-clock oscillator output; connect a crystal resonator between XCOUT and XCIN. |
| 10 | RES# | input | Reset signal input; the device enters the reset state when this pin goes low. |
| 11 | P37/XTAL | bidirectional | Port P37 shared with the main clock crystal resonator pin XTAL (8 to 24 MHz). |
| 12 | VSS | power_in | Ground pin; connect to the system ground (0 V). |
| 13 | P36/EXTAL | bidirectional | Port P36 shared with the EXTAL pin for crystal resonator or external clock input (up to 24 MHz). |
| 14 | VCC | power_in | Power supply pin (2.7 to 3.6 V); connect to VSS via a 0.1-μF multilayer ceramic capacitor placed close to the pin. |
| 15 | P35 | input | Input-only port P35 with non-maskable interrupt NMI and USB boot power selection UPSEL (low = self-powered, high = bus-powered). |
| 16 | P34 | bidirectional | Port P34 with MTIOC0A, TMCI3, PO12, POE10#, ET0_LINKSTA, SCK6/SCK0, IRQ4; also on-chip emulator TRST# input. |
| 17 | P33 | bidirectional | Port P33 with EDREQ1, MTIOC0D, TIOCD0, TMRI3, POE4#/POE11#, RXD6/RXD0, CRX0, IRQ3-DS. |
| 18 | P32 | bidirectional | Port P32 with MTIOC0C, TIOCC0, TMO3, RTCIC2, RTCOUT, POE0#/POE10#, TXD6/TXD0, CTX0, USB0_VBUSEN, IRQ2-DS. |
| 19 | P31 | bidirectional | Port P31 with MTIOC4D, TMCI2, PO9, RTCIC1, CTS1#/RTS1#/SS1#, SSLB0-A, IRQ1-DS; also on-chip emulator TMS input. |
| 20 | P30 | bidirectional | Port P30 with MTIOC4B, TMRI3, PO8, RTCIC0, POE8#, RXD1, MISOB-A, IRQ0-DS; also on-chip emulator TDI input. |
| 21 | P27 | bidirectional | Port P27 with CS7#, MTIOC2B, TMCI3, PO7, SCK1, RSPCKB-A; also on-chip emulator TCK input. |
| 22 | P26 | bidirectional | Port P26 with CS6#, MTIOC2A, TMO1, PO6, TXD1, CTS3#/RTS3#/SS3#, MOSIB-A; also on-chip emulator TDO output. |
| 23 | P25 | bidirectional | Port P25 with CS5#, EDACK1, MTIOC4C, MTCLKB, TIOCA4, PO5, RXD3, ADTRG0#. |
| 24 | P24 | bidirectional | Port P24 with CS4#, EDREQ1, MTIOC4A, MTCLKA, TIOCB4, TMRI1, PO4, SCK3, USB0_VBUSEN. |
| 25 | P23 | bidirectional | Port P23 with EDACK0, MTIOC3D, MTCLKD, TIOCD3, PO3, TXD3, CTS0#/RTS0#/SS0#. |
| 26 | P22 | bidirectional | Port P22 with EDREQ0, MTIOC3B, MTCLKC, TIOCC3, TMO0, PO2, SCK0, USB0_OVRCURB. |
| 27 | P21 | bidirectional | Port P21 with MTIOC1B, MTIOC4A, TIOCA3, TMCI0, PO1, RXD0, SCL1, USB0_EXICEN, IRQ9. |
| 28 | P20 | bidirectional | Port P20 with MTIOC1A, TIOCB3, TMRI0, PO0, TXD0, SDA1, USB0_ID, IRQ8. |
| 29 | P17 | bidirectional | Port P17 with MTIOC3A/3B/4B, TIOCB0, TCLKD, TMO1, PO15, POE8#, SCK1, TXD3, SDA2-DS, IRQ7, ADTRG1#. |
| 30 | P16 | bidirectional | Port P16 with MTIOC3C/3D, TIOCB1, TCLKC, TMO2, PO14, RTCOUT, TXD1, RXD3, SCL2-DS, USB0_VBUSEN, USB0_VBUS, USB0_OVRCURB, IRQ6, ADTRG0#. |
| 31 | P15 | bidirectional | Port P15 with MTIOC0B, MTCLKB, TIOCB2, TCLKB, TMCI2, PO13, RXD1, SCK3, CRX1-DS, IRQ5. |
| 32 | P14 | bidirectional | Port P14 with MTIOC3A, MTCLKA, TIOCB5, TCLKA, TMRI2, PO15, CTS1#/RTS1#/SS1#, CTX1, USB0_OVRCURA, IRQ4. |
| 33 | P13 | bidirectional | Port P13 with MTIOC0B, TIOCA5, TMO3, PO13, TXD2, SDA0[FM+], IRQ3, ADTRG1#. |
| 34 | P12 | bidirectional | Port P12 with TMCI1, RXD2, SCL0[FM+], IRQ2. |
| 35 | VCC_USB | power_in | USB power supply pin. |
| 36 | USB0_DM | bidirectional | USB transceiver D- data input/output. |
| 37 | USB0_DP | bidirectional | USB transceiver D+ data input/output. |
| 38 | VSS_USB | power_in | USB ground pin. |
| 39 | P55 | bidirectional | Port P55 with D0[A0/D0], WAIT#, EDREQ0, MTIOC4D, TMO3, ET0_EXOUT, CRX1, IRQ10. |
| 40 | P54 | bidirectional | Port P54 with ALE, D1[A1/D1], EDACK0, MTIOC4B, TMCI1, ET0_LINKSTA, CTS2#/RTS2#/SS2#, CTX1. |
| 41 | P53 | bidirectional | Port P53 multiplexed with BCLK external bus clock output; cannot be used as I/O port when the external bus is enabled. |
| 42 | P52 | bidirectional | Port P52 with RD#, RXD2/SMISO2/SSCL2, SSLB3-A. |
| 43 | P51 | bidirectional | Port P51 with WR1#/BC1#, WAIT#, SCK2, SSLB2-A. |
| 44 | P50 | bidirectional | Port P50 with WR0#/WR#, TXD2/SMOSI2/SSDA2, SSLB1-A. |
| 45 | PC7 | bidirectional | Port PC7 with A23/CS0#, MTIOC3A, TMO2, TOC0, CACREF, ET0_COL, TXD8/TXD10, MISOA-A, IRQ14; also USB boot mode enable input UB. |
| 46 | PC6 | bidirectional | Port PC6 with D2[A2/D2], A22/CS1#, MTIOC3C, MTCLKA, TMCI2, PO30, TIC0, ET0_ETXD3, RXD8/RXD10, MOSIA-A, IRQ13. |
| 47 | PC5 | bidirectional | Port PC5 with D3[A3/D3], A21/CS2#/WAIT#, MTIOC3B, MTCLKD, TMRI2, PO29, ET0_ETXD2, SCK8/SCK10, RSPCKA-A. |
| 48 | PC4 | bidirectional | Port PC4 with A20/CS3#, MTIOC3D, MTCLKC, TMCI1, PO25, POE0#, ET0_TX_CLK, SCK5, CTS8#/SS8#, CTS10#/SS10#, SSLA0-A. |
| 49 | PC3 | bidirectional | Port PC3 with A19, MTIOC4D, TCLKB, PO24, ET0_TX_ER, TXD5/SMOSI5/SSDA5. |
| 50 | PC2 | bidirectional | Port PC2 with A18, MTIOC4B, TCLKA, PO21, ET0_RX_DV, RXD5/SMISO5/SSCL5, SSLA3-A. |
| 51 | PC1 | bidirectional | Port PC1 with A17, MTIOC3A, TCLKD, PO18, ET0_ERXD2, SCK5, SSLA2-A, IRQ12. |
| 52 | PC0 | bidirectional | Port PC0 with A16, MTIOC3C, TCLKC, PO17, ET0_ERXD3, CTS5#/RTS5#/SS5#, SSLA1-A, IRQ14. |
| 53 | PB7 | bidirectional | Port PB7 with A15, MTIOC3B, TIOCB5, PO31, ET0_CRS, TXD9, TXD11, SDSI_D1-B. |
| 54 | PB6 | bidirectional | Port PB6 with A14, MTIOC3D, TIOCA5, PO30, ET0_ETXD1, RXD9, RXD11, SDSI_D0-B. |
| 55 | PB5 | bidirectional | Port PB5 with A13, MTIOC2A, MTIOC1B, TIOCB4, TMRI1, PO29, POE4#, ET0_ETXD0, SCK9/SCK11, SDSI_CLK-B, LCD_CLK-B. |
| 56 | PB4 | bidirectional | Port PB4 with A12, TIOCA4, PO28, ET0_TX_EN, CTS9#/SS9#, SS11#/CTS11#, SDSI_CMD-B, LCD_TCON0-B. |
| 57 | PB3 | bidirectional | Port PB3 with A11, MTIOC0A, MTIOC4A, TIOCD3, TCLKD, TMO0, PO27, POE11#, ET0_RX_ER, SCK6, SDSI_D3-B, LCD_TCON1-B. |
| 58 | PB2 | bidirectional | Port PB2 with A10, TIOCC3, TCLKC, PO26, ET0_RX_CLK, CTS6#/RTS6#/SS6#, SDSI_D2-B, LCD_TCON2-B. |
| 59 | PB1 | bidirectional | Port PB1 with A9, MTIOC0C, MTIOC4C, TIOCB3, TMCI0, PO25, ET0_ERXD0, TXD6, LCD_TCON3-B, IRQ4-DS. |
| 60 | VCC | power_in | Power supply pin (2.7 to 3.6 V); connect to VSS via a 0.1-μF multilayer ceramic capacitor placed close to the pin. |
| 61 | PB0 | bidirectional | Port PB0 with A8, MTIC5W, TIOCA3, PO24, ET0_ERXD1, RXD6, LCD_DATA0-B, IRQ12. |
| 62 | VSS | power_in | Ground pin; connect to the system ground (0 V). |
| 63 | PA7 | bidirectional | Port PA7 with A7, TIOCB2, PO23, ET0_WOL, MISOA-B, LCD_DATA1-B. |
| 64 | PA6 | bidirectional | Port PA6 with A6, MTIC5V, MTCLKB, TIOCA2, TMCI3, PO22, POE10#, ET0_EXOUT, CTS5#/SS5#, MOSIA-B, LCD_DATA2-B. |
| 65 | PA5 | bidirectional | Port PA5 with A5, MTIOC6B, TIOCB1, PO21, ET0_LINKSTA, RSPCKA-B, LCD_DATA3-B. |
| 66 | PA4 | bidirectional | Port PA4 with A4, MTIC5U, MTCLKA, TIOCA1, TMRI0, PO20, ET0_MDC, TXD5, SSLA0-B, LCD_DATA4-B, IRQ5-DS. |
| 67 | PA3 | bidirectional | Port PA3 with A3, MTIOC0D, MTCLKD, TIOCD0, TCLKB, PO19, ET0_MDIO, RXD5, LCD_DATA5-B, IRQ6-DS. |
| 68 | PA2 | bidirectional | Port PA2 with A2, MTIOC7A, PO18, RXD5/SMISO5/SSCL5, SSLA3-B, LCD_DATA6-B. |
| 69 | PA1 | bidirectional | Port PA1 with A1, MTIOC0B, MTCLKC, MTIOC7B, TIOCB0, PO17, ET0_WOL, SCK5, SSLA2-B, LCD_DATA7-B, IRQ11. |
| 70 | PA0 | bidirectional | Port PA0 with BC0#/A0, MTIOC4A, MTIOC6D, TIOCA0, PO16, CACREF, ET0_TX_EN, SSLA1-B, LCD_DATA8-B. |
| 71 | PE7 | bidirectional | Port PE7 with D15[A15/D15], MTIOC6A, TOC1, MISOB-B, SDHI_WP, MMC_RES#-B, LCD_DATA9-B, IRQ7, AN105. |
| 72 | PE6 | bidirectional | Port PE6 with D14[A14/D14], MTIOC6C, TIC1, MOSIB-B, SDHI_CD, MMC_CD-B, LCD_DATA10-B, IRQ6, AN104. |
| 73 | PE5 | bidirectional | Port PE5 with D13[A13/D13], MTIOC4C, MTIOC2B, ET0_RX_CLK, REF50CK0, RSPCKB-B, LCD_DATA11-B, IRQ5, AN103. |
| 74 | PE4 | bidirectional | Port PE4 with D12[A12/D12], MTIOC4D, MTIOC1A, PO28, ET0_ERXD2, SSLB0-B, LCD_DATA12-B, AN102. |
| 75 | PE3 | bidirectional | Port PE3 with D11[A11/D11], MTIOC4B, PO26, TOC3, POE8#, ET0_ERXD3, CTS12#/RTS12#/SS12#, MMC_D7-B, LCD_DATA13-B, AN101. |
| 76 | PE2 | bidirectional | Port PE2 with D10[A10/D10], MTIOC4A, PO23, TIC3, RXD12, SSLB3-B, MMC_D6-B, LCD_DATA14-B, IRQ7-DS, AN100. |
| 77 | PE1 | bidirectional | Port PE1 with D9[A9/D9], MTIOC4C, MTIOC3B, PO18, TXD12, SSLB2-B, MMC_D5-B, LCD_DATA15-B, ANEX1. |
| 78 | PE0 | bidirectional | Port PE0 with D8[A8/D8], MTIOC3D, SCK12, SSLB1-B, MMC_D4-B, LCD_DATA16-B, ANEX0. |
| 79 | PD7 | bidirectional | Port PD7 with D7[A7/D7], MTIC5U, POE0#, SSLC3-A, QMI-B/QIO1-B, SDHI_D1-B, MMC_D1-B, LCD_DATA17-B, IRQ7, AN107. |
| 80 | PD6 | bidirectional | Port PD6 with D6[A6/D6], MTIC5V, MTIOC8A, POE4#, SSLC2-A, QMO-B/QIO0-B, SDHI_D0-B, MMC_D0-B, LCD_DATA18-B, IRQ6, AN106. |
| 81 | PD5 | bidirectional | Port PD5 with D5[A5/D5], MTIC5W, MTIOC8C, POE10#, SSLC1-A, QSPCLK-B, SDHI_CLK-B, MMC_CLK-B, LCD_DATA19-B, IRQ5, AN113. |
| 82 | PD4 | bidirectional | Port PD4 with D4[A4/D4], MTIOC8B, POE11#, SSLC0-A, QSSL-B, SDHI_CMD-B, MMC_CMD-B, LCD_DATA20-B, IRQ4, AN112. |
| 83 | PD3 | bidirectional | Port PD3 with D3[A3/D3], MTIOC8D, TOC2, POE8#, RSPCKC-A, QIO3-B, SDHI_D3-B, MMC_D3-B, LCD_DATA21-B, IRQ3, AN111. |
| 84 | PD2 | bidirectional | Port PD2 with D2[A2/D2], MTIOC4D, TIC2, MISOC-A, CRX0, QIO2-B, SDHI_D2-B, MMC_D2-B, LCD_DATA22-B, IRQ2, AN110. |
| 85 | PD1 | bidirectional | Port PD1 with D1[A1/D1], MTIOC4B, POE0#, MOSIC-A, CTX0, LCD_DATA23-B, IRQ1, AN109. |
| 86 | PD0 | bidirectional | Port PD0 with D0[A0/D0], POE4#, LCD_EXTCLK-B, IRQ0, AN108. |
| 87 | P47 | bidirectional | Port P47 with IRQ15-DS and analog input AN007. |
| 88 | P46 | bidirectional | Port P46 with IRQ14-DS and analog input AN006. |
| 89 | P45 | bidirectional | Port P45 with IRQ13-DS and analog input AN005. |
| 90 | P44 | bidirectional | Port P44 with IRQ12-DS and analog input AN004. |
| 91 | P43 | bidirectional | Port P43 with IRQ11-DS and analog input AN003. |
| 92 | P42 | bidirectional | Port P42 with IRQ10-DS and analog input AN002. |
| 93 | P41 | bidirectional | Port P41 with IRQ9-DS and analog input AN001. |
| 94 | VREFL0 | power_in | Analog reference ground for the 12-bit A/D converter unit 0; connect to VSS if the A/D converter is not used. |
| 95 | P40 | bidirectional | Port P40 with IRQ8-DS and analog input AN000. |
| 96 | VREFH0 | power_in | Analog reference voltage supply for the 12-bit A/D converter unit 0; connect to VCC if the A/D converter is not used. |
| 97 | AVCC0 | power_in | Analog supply for the 12-bit A/D converter unit 0; connect to a branch of VCC and to AVSS0 via a 0.1-μF ceramic capacitor. |
| 98 | P07 | bidirectional | Port P07 with IRQ15 and ADTRG0# external A/D trigger input. |
| 99 | AVSS0 | power_in | Analog ground for the 12-bit A/D converter unit 0; connect to a branch of VSS. |
| 100 | P05 | bidirectional | Port P05 with IRQ13 and D/A converter output DA1. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | LQFP-100(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply voltage | VCC, VCC_USB | 2.7 | 3.6 | V | 154 | ||
| VBATT power supply voltage | VBATT | 2 | 3.6 | V | 154 | ||
| Reference voltage VREFH0 | VREFH0 | 2.7 | V | max is AVCC0 | 154 | ||
| Operating temperature (D version) | Topr | -40 | 85 | °C | 154 | ||
| Absolute max power supply voltage | VCC, VCC_USB | -0.3 | 4 | V | 154 | ||
| Absolute max VBATT voltage | VBATT | -0.3 | 4 | V | 154 | ||
| Absolute max analog power supply voltage | AVCC0, AVCC1 | -0.3 | 4 | V | 154 | ||
| Absolute max input voltage (except 5 V tolerant ports) | Vin | -0.3 | 4 | V | -0.3 to VCC + 0.3 (up to 4.0) | 154 | |
| Absolute max input voltage (5 V tolerant ports) | Vin | -0.3 | 5.8 | V | -0.3 to VCC + 4.0 (up to 5.8) | 154 | |
| Absolute max analog input voltage | VAN | -0.3 | 4 | V | -0.3 to AVCC + 0.3 (up to 4.0) | 154 | |
| Absolute max reference voltage | VREFH0 | -0.3 | 4 | V | -0.3 to AVCC0 + 0.3 (up to 4.0) | 154 | |
| Junction temperature (D version) | Tj | -40 | 105 | °C | 154 | ||
| Storage temperature | Tstg | -55 | 125 | °C | 154 | ||
| Input high voltage ETHERC input pin | VIH | 2.3 | V | ETHERC input pin | 155 | ||
| Input high voltage RIIC (SMBus) | VIH | 2.1 | V | RIIC (SMBus) | 155 | ||
| Input low voltage RIIC (SMBus) | VIL | 0.8 | V | RIIC (SMBus) | 155 | ||
| Output low voltage all output pins | VOL | 0.5 | V | IOL = 1.0 mA | 156 | ||
| Output low voltage RIIC output pin | VOL | 0.4 | V | IOL = 3.0 mA | 156 | ||
| Output low voltage RIIC output pin | VOL | 0.6 | V | IOL = 6.0 mA | 156 | ||
| Output low voltage RIIC P12/P13 ch0 | VOL | 0.4 | V | IOL = 15.0 mA (ICFER.FMPE = 1) | 156 | ||
| Output low voltage RIIC P12/P13 ch0 | VOL | 0.4 | V | IOL = 20.0 mA (ICFER.FMPE = 1) | 156 | ||
| Output low voltage ETHERC output pin | VOL | 0.4 | V | IOL = 1.0 mA | 156 | ||
| Input leakage current RES#, MD, EMLE, BSCANP, NMI | /Iin/ | 1 | μA | Vin = 0 V, Vin = VCC | 156 | ||
| Three-state leakage current (other than 5 V tolerant) | /ITSI/ | 1 | μA | Vin = 0 V, Vin = VCC | 156 | ||
| Three-state leakage current (5 V tolerant ports) | /ITSI/ | 5 | μA | Vin = 0 V, Vin = 5.5 V | 156 | ||
| Input pull-up resistor current (other than P35) | Ip | -300 | -10 | μA | VCC = 2.7 to 3.6 V, Vin = 0 V | 156 | |
| Input pull-down resistor current EMLE, BSCANP | Ip | 10 | 300 | μA | Vin = VCC | 156 | |
| Input capacitance (all input pins except listed) | Cin | 8 | pF | Vbias = 0 V, Vamp = 20 mV, f = 1 MHz, Ta = 25°C | 156 | ||
| Input capacitance (ports 03, 05, 12, 13, 16, 17, 20, 21, EMLE, BSCANP, USB0_DP, USB0_DM) | Cin | 16 | pF | Vbias = 0 V, Vamp = 20 mV, f = 1 MHz, Ta = 25°C | 156 | ||
| Thermal resistance 100-pin LFQFP (PLQP0100KB-B) | θja | 52.5 | °C/W | JESD51-2 and JESD51-7 compliant | 161 | ||
| Thermal characterization parameter 100-pin LFQFP (PLQP0100KB-B) | Ψjt | 1.5 | °C/W | JESD51-2 and JESD51-7 compliant | 161 |
CAD (KiCad official)
- Symbol:
R5F5651CDDFP#10 - Footprint:
Package_QFP:LQFP-100_14x14mm_P0.5mm - 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files:
r5f5651cddfp-10-etched.step/r5f5651cddfp-10-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);r5f5651cddfp-10.step/r5f5651cddfp-10.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (246 pp, sha256
739934bba43627d5, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).