3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownR5F562N8BDFP#V0
RENESAS · Pre-ordered MCUs · LQFP-100(14x14)
R5F562N8BDFP#V0 from RENESAS, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | Power supply pin, connect to the system power supply. |
| 2 | EMLE | input | Enables on-chip emulator connection; drive high when the emulator is used, low when not used. |
| 3 | VSS | power_in | Ground pin, connect to the system power supply (0 V). |
| 4 | MDE | input | Operating mode setting pin; its level must not be changed during operation. |
| 5 | VCL | passive | Connect to VSS via a 0.1 uF capacitor placed close to the pin. |
| 6 | MD1 | input | Operating mode setting pin; its level must not be changed during operation. |
| 7 | MD0 | input | Operating mode setting pin; its level must not be changed during operation. |
| 8 | XCIN | input | Sub-clock oscillator pin; connect a crystal resonator between XCOUT and XCIN. |
| 9 | XCOUT | output | Sub-clock oscillator pin; connect a crystal resonator between XCOUT and XCIN. |
| 10 | RES# | input | Reset input; the LSI enters the reset state when this signal goes low. |
| 11 | XTAL | output | Crystal resonator pin for the main clock. |
| 12 | VSS | power_in | Ground pin, connect to the system power supply (0 V). |
| 13 | EXTAL | input | Crystal resonator pin; an external clock signal can be input through this pin. |
| 14 | VCC | power_in | Power supply pin, connect to the system power supply. |
| 15 | P35/NMI | input | 1-bit input port and non-maskable interrupt request input. |
| 16 | P34 | bidirectional | I/O port P34 with MTU, TMR, PPG, SCI6 clock, IRQ4-A and TRST# on-chip emulator function. |
| 17 | P33 | bidirectional | I/O port P33 with MTU, PPG, CAN receive, SCI6 receive and IRQ3-A functions. |
| 18 | P32 | bidirectional | I/O port P32 with MTU, PPG, RTC 1-Hz output, CAN transmit, SCI6 transmit and IRQ2-A functions. |
| 19 | P31 | bidirectional | I/O port P31 with MTU, TMR, PPG, RSPI SSLB0-A, IRQ1 and TMS on-chip emulator function. |
| 20 | P30 | bidirectional | I/O port P30 with MTU, TMR, PPG, SCI1 receive, RSPI MISOB-A, IRQ0 and TDI on-chip emulator function. |
| 21 | P27 | bidirectional | I/O port P27 with CS7# chip select, MTU, PPG, RSPCKB-A, SCK1 and TCK on-chip emulator function. |
| 22 | P26 | bidirectional | I/O port P26 with CS6# chip select, MTU, TMR, PPG, MOSIB-A, TxD1 and TDO on-chip emulator output. |
| 23 | P25 | bidirectional | I/O port P25 with CS5# chip select, USB0 D+ pull-down enable, MTU, PPG, RxD3 and ADTRG0#-B. |
| 24 | P24 | bidirectional | I/O port P24 with CS4# chip select, USB0 VBUS enable, MTU, TMR, PPG and SCK3. |
| 25 | P23 | bidirectional | I/O port P23 with USB0 D+ pull-up enable, MTU, PPG and TxD3 functions. |
| 26 | P22 | bidirectional | I/O port P22 with USB0 D- pull-down enable, MTU, TMR, PPG and SCK0 functions. |
| 27 | P21 | bidirectional | I/O port P21 with USB0_EXICEN (OTG power supply IC connection), MTU, TMR, PPG and RxD0. |
| 28 | P20 | bidirectional | I/O port P20 with USB0_ID (OTG power supply IC connection), MTU, TMR, PPG and TxD0. |
| 29 | PLLVCC | power_in | Power supply pin for the PLL circuit, connect to the system power supply. |
| 30 | P16 | bidirectional | I/O port P16 with USB0 VBUS detection, over-current/VBUS enable, MTU, TMR, PPG and IRQ6-B. |
| 31 | PLLVSS | power_in | Ground pin for the PLL circuit. |
| 32 | P14 | bidirectional | I/O port P14 with USB0 over-current input, D+ pull-up enable, MTU, TMR, PPG and IRQ4-B. |
| 33 | P13 | bidirectional | I/O port P13 with MTU, TMR, PPG, I2C SDA0, TxD2-A, IRQ3-B and ADTRG1# A/D trigger. |
| 34 | P12 | bidirectional | I/O port P12 with TMR clock input, I2C SCL0, RxD2-A and IRQ2-B. |
| 35 | VCC_USB | power_in | USB power supply pin; connect to the system power supply even when USB is not used. |
| 36 | USB0_DM | bidirectional | Inputs or outputs D- data for the USB bus. |
| 37 | USB0_DP | bidirectional | Inputs or outputs D+ data for the USB bus. |
| 38 | VSS_USB | power_in | USB ground pin; connect to the system power supply (0 V) even when USB is not used. |
| 39 | P55/WAIT#-B/MTIOC4D-B | bidirectional | I/O port P55 with WAIT#-B external wait input and MTU function. |
| 40 | P54/MTIOC4B-B | bidirectional | I/O port P54 with MTIOC4B-B MTU function. |
| 41 | P53/BCLK | output | Outputs the external bus clock for external devices (pin is also 1-bit input port P53). |
| 42 | P52 | bidirectional | I/O port P52 with RD# read strobe, RSPI SSLB3-A and RxD2-B. |
| 43 | P51 | bidirectional | I/O port P51 with WR1#/BC1# strobe, WAIT#-D, RSPI SSLB2-A and SCK2. |
| 44 | P50 | bidirectional | I/O port P50 with WR0#/WR# write strobe, RSPI SSLB1-A and TxD2-B. |
| 45 | PC7 | bidirectional | I/O port PC7 with address A23, CS0#, Ethernet collision input, MTU and MISOA-A. |
| 46 | PC6 | bidirectional | I/O port PC6 with address A22, CS1#, Ethernet transmit data ET_ETXD3, MTU and MOSIA-A. |
| 47 | PC5 | bidirectional | I/O port PC5 with address A21, CS2#, WAIT#-C, Ethernet ET_ETXD2, MTU and RSPCKA-A. |
| 48 | PC4 | bidirectional | I/O port PC4 with address A20, CS3#, Ethernet transmit clock input, MTU clock and SSLA0-A. |
| 49 | PC3 | bidirectional | I/O port PC3 with address A19, Ethernet transmit error output, MTU clock and TxD5. |
| 50 | PC2 | bidirectional | I/O port PC2 with address A18, Ethernet ET_RX_DV, MTU clock, SSLA3-A and RxD5. |
| 51 | PC1 | bidirectional | I/O port PC1 with address A17, Ethernet receive data ET_ERXD2, MTU clock, SSLA2-A and SCK5. |
| 52 | PC0 | bidirectional | I/O port PC0 with address A16, Ethernet receive data ET_ERXD3, MTU clock and SSLA1-A. |
| 53 | PB7 | bidirectional | I/O port PB7 with address A15, Ethernet carrier sense/RMII CRS_DV, MTU and PPG. |
| 54 | PB6 | bidirectional | I/O port PB6 with address A14, Ethernet transmit data 1, MTU and PPG. |
| 55 | PB5 | bidirectional | I/O port PB5 with address A13, Ethernet transmit data 0, MTU and PPG. |
| 56 | PB4 | bidirectional | I/O port PB4 with address A12, Ethernet transmit enable, MTU and PPG. |
| 57 | PB3 | bidirectional | I/O port PB3 with address A11, Ethernet receive error input, MTU and PPG. |
| 58 | PB2 | bidirectional | I/O port PB2 with address A10, Ethernet receive clock/50-MHz RMII reference clock input, MTU and PPG. |
| 59 | PB1 | bidirectional | I/O port PB1 with address A9, Ethernet receive data 0, MTU and PPG. |
| 60 | VCC | power_in | Power supply pin, connect to the system power supply. |
| 61 | PB0 | bidirectional | I/O port PB0 with address A8, Ethernet receive data 1, MTU and PPG. |
| 62 | VSS | power_in | Ground pin, connect to the system power supply (0 V). |
| 63 | PA7 | bidirectional | I/O port PA7 with address A7, Ethernet Magic Packet output, MTU, PPG and MISOA-B. |
| 64 | PA6 | bidirectional | I/O port PA6 with address A6, Ethernet general-purpose output, MTU, PPG and MOSIA-B. |
| 65 | PA5 | bidirectional | I/O port PA5 with address A5, Ethernet link status input, MTU, PPG and RSPCKA-B. |
| 66 | PA4 | bidirectional | I/O port PA4 with address A4, Ethernet management clock output, MTU, PPG and SSLA0-B. |
| 67 | PA3 | bidirectional | I/O port PA3 with address A3, Ethernet management data I/O, MTU and PPG. |
| 68 | PA2 | bidirectional | I/O port PA2 with address A2, MTU, PPG and SSLA3-B. |
| 69 | PA1 | bidirectional | I/O port PA1 with address A1, MTU, PPG and SSLA2-B. |
| 70 | PA0 | bidirectional | I/O port PA0 with address A0/BC0#, MTU, PPG and SSLA1-B. |
| 71 | PE7/D15/MISOB-B/IRQ7 | bidirectional | I/O port PE7 with data bus D15, MISOB-B and IRQ7. |
| 72 | PE6/D14/MOSIB-B/IRQ6-A | bidirectional | I/O port PE6 with data bus D14, MOSIB-B and IRQ6-A. |
| 73 | PE5/D13/RSPCKB-B/IRQ5 | bidirectional | I/O port PE5 with data bus D13, RSPCKB-B and IRQ5. |
| 74 | PE4/D12/SSLB0-B | bidirectional | I/O port PE4 with data bus D12 and RSPI SSLB0-B. |
| 75 | PE3/D11/POE8# | bidirectional | I/O port PE3 with data bus D11 and POE8# port output enable input. |
| 76 | PE2 | bidirectional | I/O port PE2 with data bus D10, POE9# and SSLB3-B. |
| 77 | PE1/D9/SSLB2-B | bidirectional | I/O port PE1 with data bus D9 and RSPI SSLB2-B. |
| 78 | PE0/D8/SSLB1-B | bidirectional | I/O port PE0 with data bus D8 and RSPI SSLB1-B. |
| 79 | PD7/D7/MTIC5U/POE0# | bidirectional | I/O port PD7 with data bus D7, MTIC5U input capture and POE0#. |
| 80 | PD6/D6/MTIC5V/POE1# | bidirectional | I/O port PD6 with data bus D6, MTIC5V input capture and POE1#. |
| 81 | PD5/D5/MTIC5W/POE2# | bidirectional | I/O port PD5 with data bus D5, MTIC5W input capture and POE2#. |
| 82 | PD4/D4/MTIC11U-B/POE3# | bidirectional | I/O port PD4 with data bus D4, MTIC11U-B input capture and POE3#. |
| 83 | PD3/D3/MTIC11V-B/POE4# | bidirectional | I/O port PD3 with data bus D3, MTIC11V-B input capture and POE4#. |
| 84 | PD2/D2/MTIC11W-B/POE5# | bidirectional | I/O port PD2 with data bus D2, MTIC11W-B input capture and POE5#. |
| 85 | PD1/D1/POE6# | bidirectional | I/O port PD1 with data bus D1 and POE6#. |
| 86 | PD0/D0/POE7# | bidirectional | I/O port PD0 with data bus D0 and POE7#. |
| 87 | P47/AN7/IRQ15-B | bidirectional | I/O port P47 with A/D converter analog input AN7 and IRQ15-B. |
| 88 | P46/AN6/IRQ14 | bidirectional | I/O port P46 with A/D converter analog input AN6 and IRQ14. |
| 89 | P45/AN5/IRQ13-B | bidirectional | I/O port P45 with A/D converter analog input AN5 and IRQ13-B. |
| 90 | P44/AN4/IRQ12 | bidirectional | I/O port P44 with A/D converter analog input AN4 and IRQ12. |
| 91 | P43/AN3/IRQ11 | bidirectional | I/O port P43 with A/D converter analog input AN3 and IRQ11. |
| 92 | P42/AN2/IRQ10 | bidirectional | I/O port P42 with A/D converter analog input AN2 and IRQ10. |
| 93 | P41/AN1/IRQ9 | bidirectional | I/O port P41 with A/D converter analog input AN1 and IRQ9. |
| 94 | VREFL | power_in | Reference ground for the A/D and D/A converters; connect to analog reference power supply (0 V). |
| 95 | P40/AN0/IRQ8 | bidirectional | I/O port P40 with A/D converter analog input AN0 and IRQ8. |
| 96 | VREFH | power_in | Reference power supply for the A/D and D/A converters; connect to system power supply when converters are unused. |
| 97 | AVCC | power_in | Analog power supply for the A/D and D/A converters; connect to system power supply when converters are unused. |
| 98 | P07/ADTRG0#-A/IRQ15-A | bidirectional | I/O port P07 with A/D external trigger input ADTRG0#-A and IRQ15-A. |
| 99 | AVSS | power_in | Ground pin for the A/D and D/A converters; connect to system power supply (0 V). |
| 100 | P05/DA1/IRQ13-A | bidirectional | I/O port P05 with D/A converter output DA1 and IRQ13-A. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | LQFP-100(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
CAD (KiCad official)
- Symbol:
R5F562N8BDFP#V0 - Footprint:
Package_QFP:LQFP-100_14x14mm_P0.5mm - 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files:
r5f562n8bdfp-v0-etched.step/r5f562n8bdfp-v0-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);r5f562n8bdfp-v0.step/r5f562n8bdfp-v0.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (150 pp, sha256
f3218395c57fbb55, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).