component
R5F513T3AGFJ#30
Public Made by Adomby adom
RENESAS Microcontrollers (MCU/MPU/SOC), LQFP-32(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
d9ba9cb
R5F513T3AGFJ#30
RENESAS · Microcontrollers (MCU/MPU/SOC) · LQFP-32(7x7)
R5F513T3AGFJ#30 from RENESAS, in a LQFP-32(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCL | passive | Connect this pin to the VSS pin via the 4.7 μF smoothing capacitor used to stabilize the internal power supply, placed close to the pin. |
| 2 | MD | input | Operating mode setting pin; the signal level on this pin must not be changed during operation (multiplexed with FINED, the FINE on-chip emulator interface I/O). |
| 3 | RES# | input | Reset pin; the MCU enters the reset state when this signal goes low, and it should be connected to VCC via a pull-up resistor when unused. |
| 4 | P37/XTAL | output | XTAL output pin for connecting a crystal to the main clock oscillator; the pin can alternatively be used as general I/O port P37 when the main clock is not used. |
| 5 | VSS | power_in | Ground pin; connect it to the system power supply (0 V). |
| 6 | P36/EXTAL | input | EXTAL input pin for the main clock oscillator, through which an external clock can be input; the pin can alternatively be used as general I/O port P36 when the main clock is not used. |
| 7 | VCC | power_in | Power supply pin; connect it to the system power supply. |
| 8 | PE2 | input | 1-bit input-only port pin that also serves as the NMI non-maskable interrupt request input and POE10# request input; connect it to VCC via a pull-up resistor when unused. |
| 9 | PB7 | bidirectional | General I/O port pin multiplexed with MTIOC3C/MTCLKD, SCI1/SCI5 serial signals and IRQ5; input pull-up, open-drain output and drive capacity switching are available. |
| 10 | PB6 | bidirectional | General I/O port pin multiplexed with MTIOC1B/MTIOC3A and SCI1/SCI5 transmit signals; fixed to high drive output and 5-V tolerant with input pull-up and open-drain output available. |
| 11 | PB3 | bidirectional | General I/O port pin multiplexed with MTIOC0A/CACREF and SCI5/SCI12 clock SCK5/SCK12; input pull-up, open-drain output and drive capacity switching are available. |
| 12 | PB2 | bidirectional | General I/O port pin multiplexed with MTIOC0B/MTCLKC/ADSM0, SCI5 transmit signals and SDA0; fixed to high drive output and 5-V tolerant. |
| 13 | PB1 | bidirectional | General I/O port pin multiplexed with MTIOC0C/MTIC5W/MTCLKA, SCI5 receive signals, SCL0 and IRQ2; fixed to high drive output and 5-V tolerant, with TTL input level when SCL is selected with SMBus in RIIC. |
| 14 | PB0 | bidirectional | General I/O port pin multiplexed with MTIOC0D/MTIOC2A/MTCLKB and SCI12 transmit signals; input pull-up, open-drain output and drive capacity switching are available. |
| 15 | P94 | bidirectional | General I/O port pin multiplexed with MTIOC2B/MTIC5U/MTCLKA, SCI12 receive signals and IRQ1; input pull-up, open-drain output and drive capacity switching are available. |
| 16 | P93 | bidirectional | General I/O port pin multiplexed with MTIOC1A/MTIC5V, SCI5/SCI12 clock SCK5/SCK12, IRQ0 and ADTRG0# A/D trigger input; input pull-up, open-drain output and drive capacity switching are available. |
| 17 | P76 | bidirectional | General I/O port pin multiplexed with MTIOC4D; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 18 | P75 | bidirectional | General I/O port pin multiplexed with MTIOC4C; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 19 | P74 | bidirectional | General I/O port pin multiplexed with MTIOC3D; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 20 | P73 | bidirectional | General I/O port pin multiplexed with MTIOC4B; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 21 | P72 | bidirectional | General I/O port pin multiplexed with MTIOC4A; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 22 | P71 | bidirectional | General I/O port pin multiplexed with MTIOC3B; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 23 | VCC | power_in | Power supply pin; connect it to the system power supply. |
| 24 | VSS | power_in | Ground pin; connect it to the system power supply (0 V). |
| 25 | P44 | bidirectional | General I/O port pin shared with analog input AN004 and comparator input CMPC12; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 26 | P43 | bidirectional | General I/O port pin shared with analog input AN003 and comparator input CMPC02; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 27 | P42 | bidirectional | General I/O port pin shared with analog input AN002 and comparator input CMPC20; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 28 | P41 | bidirectional | General I/O port pin shared with analog input AN001 and comparator input CMPC10; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 29 | P40 | bidirectional | General I/O port pin shared with analog input AN000 and comparator input CMPC00; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 30 | AVCC0 | power_in | Analog voltage supply pin for the 12-bit A/D converter, comparator C and the 8-bit D/A converter; connect it to VCC when these modules are not used. |
| 31 | AVSS0 | power_in | Analog ground pin for the 12-bit A/D converter, comparator C and the 8-bit D/A converter; connect it to VSS when these modules are not used. |
| 32 | P11 | bidirectional | General I/O port pin multiplexed with MTIOC3A/MTCLKA/POE8#, IRQ1 and CVREFC0 comparator reference voltage input; input pull-up, open-drain output and drive capacity switching are available. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | LQFP-32(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 32 |
CAD (KiCad official)
- Symbol:
R5F513T3AGFJ#30 - Footprint:
Package_QFP:LQFP-32_7x7mm_P0.8mm - 3D model: LQFP-32(7x7) (KiCad packages3D, STEP)
- 3D model files:
r5f513t3agfj-30-etched.step/r5f513t3agfj-30-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);r5f513t3agfj-30.step/r5f513t3agfj-30.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (1055 pp, sha256
b57248feedc44923, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# R5F513T3AGFJ#30
**RENESAS** · Microcontrollers (MCU/MPU/SOC) · LQFP-32(7x7)
R5F513T3AGFJ#30 from RENESAS, in a LQFP-32(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCL | passive | Connect this pin to the VSS pin via the 4.7 μF smoothing capacitor used to stabilize the internal power supply, placed close to the pin. |
| 2 | MD | input | Operating mode setting pin; the signal level on this pin must not be changed during operation (multiplexed with FINED, the FINE on-chip emulator interface I/O). |
| 3 | RES# | input | Reset pin; the MCU enters the reset state when this signal goes low, and it should be connected to VCC via a pull-up resistor when unused. |
| 4 | P37/XTAL | output | XTAL output pin for connecting a crystal to the main clock oscillator; the pin can alternatively be used as general I/O port P37 when the main clock is not used. |
| 5 | VSS | power_in | Ground pin; connect it to the system power supply (0 V). |
| 6 | P36/EXTAL | input | EXTAL input pin for the main clock oscillator, through which an external clock can be input; the pin can alternatively be used as general I/O port P36 when the main clock is not used. |
| 7 | VCC | power_in | Power supply pin; connect it to the system power supply. |
| 8 | PE2 | input | 1-bit input-only port pin that also serves as the NMI non-maskable interrupt request input and POE10# request input; connect it to VCC via a pull-up resistor when unused. |
| 9 | PB7 | bidirectional | General I/O port pin multiplexed with MTIOC3C/MTCLKD, SCI1/SCI5 serial signals and IRQ5; input pull-up, open-drain output and drive capacity switching are available. |
| 10 | PB6 | bidirectional | General I/O port pin multiplexed with MTIOC1B/MTIOC3A and SCI1/SCI5 transmit signals; fixed to high drive output and 5-V tolerant with input pull-up and open-drain output available. |
| 11 | PB3 | bidirectional | General I/O port pin multiplexed with MTIOC0A/CACREF and SCI5/SCI12 clock SCK5/SCK12; input pull-up, open-drain output and drive capacity switching are available. |
| 12 | PB2 | bidirectional | General I/O port pin multiplexed with MTIOC0B/MTCLKC/ADSM0, SCI5 transmit signals and SDA0; fixed to high drive output and 5-V tolerant. |
| 13 | PB1 | bidirectional | General I/O port pin multiplexed with MTIOC0C/MTIC5W/MTCLKA, SCI5 receive signals, SCL0 and IRQ2; fixed to high drive output and 5-V tolerant, with TTL input level when SCL is selected with SMBus in RIIC. |
| 14 | PB0 | bidirectional | General I/O port pin multiplexed with MTIOC0D/MTIOC2A/MTCLKB and SCI12 transmit signals; input pull-up, open-drain output and drive capacity switching are available. |
| 15 | P94 | bidirectional | General I/O port pin multiplexed with MTIOC2B/MTIC5U/MTCLKA, SCI12 receive signals and IRQ1; input pull-up, open-drain output and drive capacity switching are available. |
| 16 | P93 | bidirectional | General I/O port pin multiplexed with MTIOC1A/MTIC5V, SCI5/SCI12 clock SCK5/SCK12, IRQ0 and ADTRG0# A/D trigger input; input pull-up, open-drain output and drive capacity switching are available. |
| 17 | P76 | bidirectional | General I/O port pin multiplexed with MTIOC4D; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 18 | P75 | bidirectional | General I/O port pin multiplexed with MTIOC4C; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 19 | P74 | bidirectional | General I/O port pin multiplexed with MTIOC3D; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 20 | P73 | bidirectional | General I/O port pin multiplexed with MTIOC4B; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 21 | P72 | bidirectional | General I/O port pin multiplexed with MTIOC4A; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 22 | P71 | bidirectional | General I/O port pin multiplexed with MTIOC3B; fixed to high drive output and 5-V tolerant with input pull-up available. |
| 23 | VCC | power_in | Power supply pin; connect it to the system power supply. |
| 24 | VSS | power_in | Ground pin; connect it to the system power supply (0 V). |
| 25 | P44 | bidirectional | General I/O port pin shared with analog input AN004 and comparator input CMPC12; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 26 | P43 | bidirectional | General I/O port pin shared with analog input AN003 and comparator input CMPC02; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 27 | P42 | bidirectional | General I/O port pin shared with analog input AN002 and comparator input CMPC20; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 28 | P41 | bidirectional | General I/O port pin shared with analog input AN001 and comparator input CMPC10; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 29 | P40 | bidirectional | General I/O port pin shared with analog input AN000 and comparator input CMPC00; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input. |
| 30 | AVCC0 | power_in | Analog voltage supply pin for the 12-bit A/D converter, comparator C and the 8-bit D/A converter; connect it to VCC when these modules are not used. |
| 31 | AVSS0 | power_in | Analog ground pin for the 12-bit A/D converter, comparator C and the 8-bit D/A converter; connect it to VSS when these modules are not used. |
| 32 | P11 | bidirectional | General I/O port pin multiplexed with MTIOC3A/MTCLKA/POE8#, IRQ1 and CVREFC0 comparator reference voltage input; input pull-up, open-drain output and drive capacity switching are available. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | LQFP-32(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 32 |
## CAD (KiCad official)
- Symbol: `R5F513T3AGFJ#30`
- Footprint: `Package_QFP:LQFP-32_7x7mm_P0.8mm`
- 3D model: LQFP-32(7x7) (KiCad packages3D, STEP)
- 3D model files: `r5f513t3agfj-30-etched.step` / `r5f513t3agfj-30-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `r5f513t3agfj-30.step` / `r5f513t3agfj-30.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [RENESAS datasheet](https://www.renesas.com/us/en/document/mah/rx13t-group-users-manual-hardware-rev110) (1055 pp, sha256 `b57248feedc44923`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/r5f513t3agfj-30-datasheet.pdf)