Generated by kicad-footprint-generator · KiCad file format 20260206
R5F51136ADFM#3A
RENESAS · Pre-ordered MCUs · LQFP-64(10x10)
R5F51136ADFM#3A from RENESAS, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PJ0 | bidirectional | General I/O port PJ0 multiplexed with the 12-bit D/A converter channel 0 analog output DA0; when PJ0 is used as a general I/O port, VCC must be less than or equal to AVCC0. |
| 2 | P27 | bidirectional | General I/O port P27 with MTIOC2B/TMCI3, SCK1/SCK12/RXD6/SMISO6/SSCL6, IRQ3, comparator-related CMPA2, CACREF and ADTRG0# functions. |
| 3 | P26 | bidirectional | General I/O port P26 with MTIOC2A/TMO1, TXD1/SMOSI1/SSDA1, USB0_VBUSEN (VBUS supply enable output for the OTG chip) and TXD6/SMOSI6/SSDA6 functions. |
| 4 | P30 | bidirectional | General I/O port P30 with MTIOC4B/POE8#/TMRI3, RXD1/SMISO1/SSCL1, LCD capacitor connection CAPH and IRQ0 functions. |
| 5 | P31 | bidirectional | General I/O port P31 with MTIOC4D/TMCI2, CTS1#/RTS1#/SS1#, LCD capacitor connection CAPL and IRQ1 functions. |
| 6 | MD | input | MD is the operating-mode setting pin whose signal level must not be changed during operation; the FINED fine interface I/O is multiplexed on this pin. |
| 7 | RES# | input | Reset pin; the MCU enters the reset state when this signal goes low. |
| 8 | XCOUT | output | Output pin of the sub-clock oscillator; a crystal is connected between XCIN and XCOUT. |
| 9 | XCIN | input | Input pin of the sub-clock oscillator (32.768 kHz); a crystal is connected between XCIN and XCOUT. |
| 10 | P35/NMI | input | UPSEL is the boot-mode pin for the USB interface, multiplexed with general input port P35 and the non-maskable interrupt input NMI. |
| 11 | XTAL | passive | Pin for connecting the main clock crystal; an external clock can also be input through this pin. |
| 12 | EXTAL | input | Pin for connecting the main clock crystal (main clock oscillator 1 to 20 MHz) together with XTAL. |
| 13 | VCL | passive | Connect this pin to VSS via a 4.7 µF multilayer ceramic smoothing capacitor placed close to the pin; do not apply the power supply voltage to this pin. |
| 14 | VSS | power_in | Ground pin; connect to the system power supply (0 V). |
| 15 | VCC | power_in | Power supply pin; connect to the system power supply, which operates from 1.8 V to 3.6 V. |
| 16 | P32 | bidirectional | General I/O port P32 with MTIOC0C/RTCOUT/TMO3, TXD6/SMOSI6/SSDA6/CTS6#/RTS6#/SS6# and IRQ2 functions. |
| 17 | P17 | bidirectional | General I/O port P17 with MTIOC0C/MTIOC3A/MTIOC3B/POE8#/TMO1, SCK1/MISOA/SDA0/RXD12/SMISO12/SSCL12 and IRQ7 functions. |
| 18 | P16 | bidirectional | General I/O port P16 with MTIOC3C/MTIOC3D/RTCOUT/TMO2, TXD1/MOSIA/SCL0, USB0_VBUS/USB0_VBUSEN/USB0_OVRCURB, IRQ6 and ADTRG0# functions. |
| 19 | P15 | bidirectional | General I/O port P15 with MTIOC0B/MTCLKB/TMCI2, RXD1/SMISO1/SSCL1/RSPCKA, IRQ5, CLKOUT and CACREF functions. |
| 20 | P14 | bidirectional | UB# is the boot-mode pin for the USB interface, multiplexed with general I/O port P14 which also provides MTIOC0A/MTIOC3A/MTCLKA/TMRI2, serial functions, USB0_OVRCURA and IRQ4. |
| 21 | VCC_USB | power_in | Power supply pin for the USB; connect this pin to VCC. |
| 22 | USB0_DM | bidirectional | D- I/O pin of the USB 2.0 host/function on-chip transceiver. |
| 23 | USB0_DP | bidirectional | D+ I/O pin of the USB 2.0 host/function on-chip transceiver. |
| 24 | VSS_USB | power_in | Ground pin for USB; connect this pin to VSS. |
| 25 | P55 | bidirectional | General I/O port P55 with MTIOC4D/TMO3 and LCD voltage pin VL1 functions. |
| 26 | P54 | bidirectional | General I/O port P54 with MTIOC4B/TMCI1 and LCD voltage pin VL2 functions. |
| 27 | PC7 | bidirectional | General I/O port PC7 with MTIOC3A/MTCLKB/TMO2, TXD1/MISOA/TXD8/SMOSI8/SSDA8, USB0_OVRCURB, LCD voltage pin VL3 and CACREF functions. |
| 28 | PC6 | bidirectional | General I/O port PC6 with MTIOC3C/MTCLKA/TMCI2, RXD1/SMISO1/SSCL1/MOSIA/RXD8/SMISO8/SSCL8, USB0_EXICEN and LCD voltage pin VL4 functions. |
| 29 | PC5 | bidirectional | General I/O port PC5 with MTIOC3B/MTCLKD/TMRI2, SCK1/RSPCKA/SCK8, USB0_ID and LCD common signal output COM0. |
| 30 | PC4 | bidirectional | General I/O port PC4 with MTIOC3D/MTCLKC/POE0#/TMCI1, SSLA0/CTS8#/RTS8#/SS8#/SCK5, USB0_VBUSEN, LCD common signal output COM1, IRQ2 and CLKOUT; the USB0_VBUS function of this pin is not 5 V tolerant. |
| 31 | PC3 | bidirectional | General I/O port PC3 with MTIOC4D, TXD5/SMOSI5/SSDA5/IRTXD5 and LCD common signal output COM2. |
| 32 | PC2 | bidirectional | General I/O port PC2 with MTIOC4B, RXD5/SMISO5/SSCL5/SSLA3/IRRXD5 and LCD common signal output COM3. |
| 33 | PB7/PC1 | bidirectional | Multiplexed pin PB7/PC1 whose listed functions are MTIOC3B, TXD9/SMOSI9/SSDA9/SSITXD0, LCD segment SEG11 and common output COM4. |
| 34 | PB6/PC0 | bidirectional | Multiplexed pin PB6/PC0 whose listed functions are MTIOC3D, RXD9/SMISO9/SSCL9/SSIRXD0, LCD segment SEG12 and common output COM5. |
| 35 | PB5 | bidirectional | General I/O port PB5 with MTIOC2A/MTIOC1B/POE1#/TMRI1, SCK9/SSISCK0, LCD segment SEG13 and common output COM6. |
| 36 | PB3 | bidirectional | General I/O port PB3 with MTIOC0A/MTIOC3B/MTIOC4A/POE3#/TMO0, SCK6/AUDIO_MCLK/USB0_OVRCURA, LCD segment SEG15 and common output COM7. |
| 37 | PB1 | bidirectional | General I/O port PB1 with MTIOC0C/MTIOC4C/TMCI0, TXD6/SMOSI6/SSDA6/SSIWS0, LCD segment SEG17 and IRQ4. |
| 38 | VCC | power_in | Power supply pin; connect to the system power supply, which operates from 1.8 V to 3.6 V. |
| 39 | PB0 | bidirectional | General I/O port PB0 with MTIC5W/MTIOC0C/RTCOUT, SCL0/RSPCKA/RXD6/SMISO6/SSCL6, IRQ2 and ADTRG0# functions. |
| 40 | VSS | power_in | Ground pin; connect to the system power supply (0 V). |
| 41 | PA6 | bidirectional | General I/O port PA6 with MTIC5V/MTCLKB/MTIOC2A/POE2#/TMCI3, CTS5#/RTS5#/SS5#/SDA0/MOSIA and IRQ3 functions. |
| 42 | PA4 | bidirectional | General I/O port PA4 with MTIC5U/MTCLKA/MTIOC2B/TMRI0, TXD5/SMOSI5/SSDA5/IRTXD5/SSLA0, LCD segment SEG20, IRQ5 and CVREFB1 functions. |
| 43 | PA3 | bidirectional | General I/O port PA3 with MTIOC0D/MTCLKD/MTIOC1B/POE0#, RXD5/SMISO5/SSCL5/IRRXD5/MISOA, LCD segment SEG21, IRQ6 and comparator input CMPB1. |
| 44 | PA1 | bidirectional | General I/O port PA1 with MTIOC0B/MTCLKC/RTCOUT, SCK5/SSLA2 and LCD segment SEG23 functions. |
| 45 | PA0 | bidirectional | General I/O port PA0 with MTIOC4A, SSLA1, LCD segment SEG24 and CACREF functions. |
| 46 | PE5 | bidirectional | General I/O port PE5 with MTIOC4C/MTIOC2B, MISOA/TXD9/SMOSI9/SSDA9, LCD segment SEG27, IRQ5, analog input AN013 and comparator output CMPOB1. |
| 47 | PE4 | bidirectional | General I/O port PE4 with MTIOC4D/MTIOC1A/MTIOC3A, MOSIA/RXD9/SMISO9/SSCL9/SSIWS0, LCD segment SEG28, IRQ4 and analog input AN012. |
| 48 | PE3 | bidirectional | General I/O port PE3 with MTIOC0A/MTIOC1B/MTIOC4B/POE8#, CTS12#/RTS12#/SS12#/RSPCKA/SCK9/AUDIO_MCLK, LCD segment SEG29, IRQ3 and analog input AN011. |
| 49 | PE2 | bidirectional | General I/O port PE2 with MTIOC4A, RXD12/SMISO12/SSCL12/SSIRXD0, LCD segment SEG30, IRQ7, analog input AN010 and CVREFB0. |
| 50 | PE1 | bidirectional | General I/O port PE1 with MTIOC4C, TXD12/SMOSI12/SSDA12/SSITXD0, LCD segment SEG31, IRQ1, analog input AN009 and comparator input CMPB0. |
| 51 | PE0 | bidirectional | General I/O port PE0 with MTIOC2A/POE3#, SCK12/CTS9#/RTS9#/SS9#/SSISCK0, LCD segment SEG32, IRQ0 and analog input AN008. |
| 52 | PE7 | bidirectional | General I/O port PE7 with LCD segment SEG33, IRQ7, analog input AN015 and comparator output CMPOB0. |
| 53 | PE6 | bidirectional | General I/O port PE6 with LCD segment SEG34, IRQ6 and analog input AN014. |
| 54 | PD2 | bidirectional | General I/O port PD2 with MTIOC4D, LCD segment SEG37 and IRQ2. |
| 55 | PD1 | bidirectional | General I/O port PD1 with MTIOC4B, LCD segment SEG38 and IRQ1. |
| 56 | PD0 | bidirectional | General I/O port PD0 with LCD segment SEG39 and IRQ0. |
| 57 | P42/VREFL | power_in | Analog reference ground pin for the 12-bit D/A converter, multiplexed with general I/O port P42 (analog input AN002) whose I/O buffer is powered from AVCC0. |
| 58 | P41/VREFH | power_in | Analog reference voltage supply pin for the 12-bit D/A converter, multiplexed with general I/O port P41 (analog input AN001) whose I/O buffer is powered from AVCC0. |
| 59 | PJ7/VREFL0 | power_in | Analog reference ground pin for the 12-bit A/D converter, multiplexed with general I/O port PJ7 whose I/O buffer is powered from AVCC0. |
| 60 | P40 | bidirectional | General I/O port P40 with 12-bit A/D analog input AN000; its I/O buffer is powered from AVCC0. |
| 61 | PJ6/VREFH0 | power_in | Analog reference voltage supply pin for the 12-bit A/D converter, multiplexed with general I/O port PJ6 whose I/O buffer is powered from AVCC0. |
| 62 | AVSS0 | power_in | Analog ground pin for the 12-bit A/D converter and D/A converter; connect to VSS when these converters are not used. |
| 63 | AVCC0 | power_in | Analog voltage supply pin for the 12-bit A/D converter and D/A converter; connect to VCC when these converters are not used. |
| 64 | PJ2 | bidirectional | General I/O port PJ2 multiplexed with the 12-bit D/A converter channel 1 analog output DA1; when PJ2 is used as a general I/O port, VCC must be less than or equal to AVCC0. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply voltage | VCC, VCC_USB | -0.3 | 4.6 | V | VSS = AVSS0 = VREFL0 = VREFL = VSS_USB = 0 V | 54 | |
| Input voltage, ports for 5 V tolerant | Vin | -0.3 | 6.5 | V | VSS = AVSS0 = VREFL0 = VREFL = VSS_USB = 0 V | 54 | |
| Input voltage, ports P40 to P44, P46, P90 to P92, PJ6, PJ7 | Vin | -0.3 | V | VSS = AVSS0 = VREFL0 = VREFL = VSS_USB = 0 V | 54 | ||
| Input voltage, other ports | Vin | -0.3 | V | VSS = AVSS0 = VREFL0 = VREFL = VSS_USB = 0 V | 54 | ||
| Reference power supply voltage | VREFH0 | -0.3 | V | VSS = AVSS0 = VREFL0 = VREFL = VSS_USB = 0 V | 54 | ||
| Analog power supply voltage | AVCC0 | -0.3 | 4.6 | V | VSS = AVSS0 = VREFL0 = VREFL = VSS_USB = 0 V | 54 | |
| Analog input voltage (AN000 to AN007, AN021 used) | VAN | -0.3 | V | VSS = AVSS0 = VREFL0 = VREFL = VSS_USB = 0 V | 54 | ||
| Analog input voltage (AN008 to AN015 used) | VAN | -0.3 | V | VSS = AVSS0 = VREFL0 = VREFL = VSS_USB = 0 V | 54 | ||
| LCD voltage VL1 | VL1 | -0.3 | 2.8 | V | 54 | ||
| LCD voltage VL2 | VL2 | -0.3 | 6.5 | V | 54 | ||
| LCD voltage VL3 | VL3 | -0.3 | 6.5 | V | 54 | ||
| LCD voltage VL4 | VL4 | -0.3 | 6.5 | V | 54 | ||
| Operating temperature | Topr | -40 | 85 | °C | D version | 54 | |
| Storage temperature | Tstg | -55 | 125 | °C | 54 | ||
| Power supply voltages (USB not used) | VCC | 1.8 | 3.6 | V | When USB not used | 55 | |
| Power supply voltages (USB used) | VCC | 3 | 3.6 | V | When USB used | 55 | |
| Analog power supply voltages | AVCC0 | 1.8 | 3.6 | V | 55 | ||
| Reference power supply voltage | VREFH0 | 1.8 | V | 55 | |||
| Input voltage, RIIC input pin (SMBus) | VIH | 2.1 | V | 2.7 V ≤ VCC ≤ 3.6 V, Ta = -40 to +105°C | 56 | ||
| Schmitt trigger input voltage, ports P16, P17, PA6, PB0 (5 V tolerant) | VIH | 5.8 | V | 2.7 V ≤ VCC ≤ 3.6 V, Ta = -40 to +105°C | 56 | ||
| Input voltage, RIIC input pin (except SMBus) | VIL | -0.3 | V | 2.7 V ≤ VCC ≤ 3.6 V, Ta = -40 to +105°C | 56 | ||
| Input voltage, other than RIIC input pin | VIL | -0.3 | V | 2.7 V ≤ VCC ≤ 3.6 V, Ta = -40 to +105°C | 56 | ||
| Input voltage, RIIC input pin (SMBus) | VIL | -0.3 | 0.8 | V | 2.7 V ≤ VCC ≤ 3.6 V, Ta = -40 to +105°C | 56 | |
| Input leakage current, RES#, MD, port P35 | Iin | 1 | µA | Vin = 0 V, VCC | 57 | ||
| Three-state leakage current (off-state), ports for 5 V tolerant | ITSI | 1 | µA | Vin = 0 V, 5.8 V | 57 | ||
| Input capacitance, all input pins (except port P16, P35, USB0_DM, USB0_DP) | Cin | 15 | pF | Vin = 0 V, Frequency: 1 MHz, Ta = 25°C | 57 | ||
| Input pull-up resistor, all ports (except port P35) | RU | 10 | 20 | 100 | kΩ | Vin = 0 V | 57 |
| Supply current, high-speed operating mode, normal, all peripheral operation max | ICC | 30 | mA | All peripheral operation: Max., ICLK = 32 MHz | 58 | ||
| Supply current, middle-speed operating mode, normal, all peripheral operation max | ICC | 14.2 | mA | All peripheral operation: Max., ICLK = 12 MHz | 58 | ||
| Supply current, low-speed operating mode, normal, all peripheral operation max | ICC | 62 | µA | All peripheral operation: Max., ICLK = 32.768 kHz | 59 | ||
| Supply current, software standby mode | ICC | 0.44 | 0.98 | µA | Ta = 25°C | 61 | |
| Supply current, software standby mode | ICC | 0.8 | 3.47 | µA | Ta = 55°C | 61 | |
| Supply current, software standby mode | ICC | 2.7 | 12 | µA | Ta = 85°C | 61 | |
| Supply current, software standby mode | ICC | 6.17 | 42.7 | µA | Ta = 105°C | 61 | |
| Permissible total consumption power | Pd | 300 | mW | D version (Ta = -40 to 85°C) | 63 | ||
| Analog power supply current, during A/D conversion (at high-speed conversion) | IAVCC | 0.7 | 1.2 | mA | 63 | ||
| Analog power supply current, during D/A conversion (per channel) | IAVCC | 0.4 | 0.8 | mA | 63 | ||
| Analog power supply current, waiting for A/D and D/A conversion (all units) | IAVCC | 0.4 | µA | 63 | |||
| Reference power supply current, during A/D conversion (at high-speed conversion) | IREFH0 | 25 | 52 | µA | 63 | ||
| Reference power supply current, waiting for A/D conversion (all units) | IREFH0 | 60 | nA | 63 | |||
| Reference power supply current, during D/A conversion | IREFH | 50 | 100 | µA | 63 | ||
| Reference power supply current, waiting for D/A conversion (all units) | IREFH | 100 | nA | 63 | |||
| RAM standby voltage | VRAM | 1.8 | V | 64 | |||
| Power-on VCC rising gradient, at normal startup | SrVCC | 0.02 | 20 | ms/V | At normal startup | 64 | |
| Power-on VCC rising gradient, voltage monitoring 1 reset enabled at startup | SrVCC | 0.02 | ms/V | Voltage monitoring 1 reset enabled at startup | 64 | ||
| Allowable ripple frequency | fr (VCC) | 10 | kHz | Vr (VCC) ≤ 0.2 × VCC | 65 | ||
| Allowable ripple frequency | fr (VCC) | 1 | MHz | Vr (VCC) ≤ 0.08 × VCC | 65 | ||
| Allowable ripple frequency | fr (VCC) | 10 | MHz | Vr (VCC) ≤ 0.06 × VCC | 65 | ||
| Allowable voltage change rising/falling gradient | dt/dVCC | 1 | ms/V | When VCC change exceeds VCC ±10% | 65 | ||
| Decoupling capacitance tolerance, CVCL (+50/-70%) | CVCL | -70 | 50 | % | 66 | ||
| Permissible output low current (average value per pin), ports other than P40 to P44, P46, P90 to P92, PJ6, PJ7 | IOL | 8 | mA | Ta = -40 to +85°C (D version) | 66 | ||
| Permissible output high current (average value per pin), ports other than P40 to P44, P46, P90 to P92, PJ6, PJ7 | IOH | -4 | mA | Ta = -40 to +85°C (D version) | 66 | ||
| Permissible output low current, total of all output pins | ΣIOL | 60 | mA | Ta = -40 to +85°C (D version) | 66 | ||
| Permissible output high current, total of all output pins | ΣIOH | -40 | mA | Ta = -40 to +85°C (D version) | 66 | ||
| Low-level output voltage, all output ports (except RIIC, ports P40 to P44, P46, P90 to P92, PJ6, PJ7) | VOL | 0.6 | V | 2.7 V ≤ VCC ≤ 3.6 V, Ta = -40 to +105°C; VIOL = 3.0 mA | 68 | ||
| Low-level output voltage, all output ports (except RIIC, ports P40 to P44, P46, P90 to P92, PJ6, PJ7) | VOL | 0.4 | V | 2.7 V ≤ VCC ≤ 3.6 V, Ta = -40 to +105°C; IOL = 1.5 mA | 68 | ||
| Low-level output voltage, ports P40 to P44, P46, P90 to P92, PJ6, PJ7 | VOL | 0.4 | V | 2.7 V ≤ VCC ≤ 3.6 V, Ta = -40 to +105°C; IOL = 0.4 mA | 68 | ||
| System clock (ICLK) maximum operating frequency, high-speed operating mode | fmax | 32 | MHz | 2.7 V ≤ VCC ≤ 3.6 V | 76 |
CAD (KiCad official)
- Symbol:
R5F51136ADFM#3A - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
r5f51136adfm-3a-etched.step/r5f51136adfm-3a-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);r5f51136adfm-3a.step/r5f51136adfm-3a.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (131 pp, sha256
c748a3546aae880b, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).