main
Ray
Publish 0.1.0
7dda6e0
PTH08000WAH
Texas Instruments · Power Modules · DIP-6
PTH08000WAH from Texas Instruments, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | This is the common ground connection for the VI and VO power connections and the 0-VDC reference for the Inhibit, VO Adjust, and Track control inputs. |
| 2 | Track | input | This analog control input lets the output voltage follow an external voltage on a volt-for-volt basis from 0 V up to the set-point voltage, has an input current of -130 µA maximum to GND, and should be connected to VI if unused. |
| 3 | VI | power_in | This is the positive input voltage power node to the module, referenced to common GND, with an input voltage range of 4.5 V to 14 V. |
| 4 | Inhibit | input | This open-collector/drain-negative logic input referenced to GND disables the module output when driven low and must not have an external pull-up. |
| 5 | VO Adjust | input | A 1% resistor between this pin and GND (pin 1) sets the output voltage above 0.9 V over a set-point range of 0.9 V to 5.5 V, with a resistor temperature stability of 100 ppm/°C or better, and the output defaults to 0.9 V if left open. |
| 6 | VO | power_out | This is the regulated positive power output with respect to the GND node. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | DIP-6 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating free-air temperature | TA | -40 | 85 | °C | Over VI range | 2 | |
| Lead temperature (H suffix) | 260 | °C | 5 seconds | 2 | |||
| Storage temperature | Tstg | -55 | 125 | °C | 2 | ||
| Input voltage | VI | 4.5 | 14 | V | 2 | ||
| Operating free-air temperature | TA | -40 | 85 | °C | 2 | ||
| Output current | IO | 0 | 2.25 | A | TA = 85°C, natural convection airflow | 3 | |
| Input voltage range | VI | 4.5 | 14 | V | Over IO range | 3 | |
| Set-point voltage tolerance | 2 | % | TA = 25°C | 3 | |||
| Temperature variation | 0.5 | %VO | -40°C ≤ TA ≤ 85°C | 3 | |||
| Line regulation | VO | 7 | mV | Over VI range | 3 | ||
| Load regulation | 0.13 | %VO | Over IO range | 3 | |||
| Total output voltage variation | 3 | %VO | Includes set-point, line, load, -40°C ≤ TA ≤ 85°C | 3 | |||
| Output voltage adjust range | V(ADJ) | 0.9 | 5.5 | V | Over IO range | 3 | |
| Output voltage ripple | 40 | mVPP | 20-MHz bandwidth | 3 | |||
| Undervoltage lockout, increasing | UVLO | 4.35 | 4.5 | V | VI = increasing | 3 | |
| Undervoltage lockout, decreasing | UVLO | 3.6 | 4 | V | VI = decreasing | 3 | |
| Input low voltage (VIL) | VIL | -0.2 | 0.5 | V | Inhibit control (pin 4) | 3 | |
| Equivalent series resistance (nonceramic) | 10 | mΩ | Nonceramic | 3 | |||
| External input capacitance, electrolytic | CI | 100 | µF | Electrolytic type (CI) | 3 | ||
| External output capacitance, nonceramic | CO | 330 | µF | Nonceramic type (CO) | 3 | ||
| External output capacitance, ceramic | CO | 220 | µF | Ceramic type (CO) | 3 | ||
| Track slew rate capability | dVtrack/dt | 1 | V/ms | CO ≤ CO(max) | 3 | ||
| Transient response over/undershoot | 100 | mV | CO = 100 µF, 1 A/µs; load step from 50% to 100% IO | 3 |
CAD (KiCad official)
- Symbol:
PTH08000WAH - Footprint:
Package_DIP:DIP-6_W7.62mm - 3D model: DIP-6 (KiCad packages3D, STEP)
- 3D model files:
pth08000wah-etched.step/pth08000wah-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pth08000wah.step/pth08000wah.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (20 pp, sha256
44479cb1240faddf, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PTH08000WAH
**Texas Instruments** · Power Modules · DIP-6
PTH08000WAH from Texas Instruments, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | This is the common ground connection for the VI and VO power connections and the 0-VDC reference for the Inhibit, VO Adjust, and Track control inputs. |
| 2 | Track | input | This analog control input lets the output voltage follow an external voltage on a volt-for-volt basis from 0 V up to the set-point voltage, has an input current of -130 µA maximum to GND, and should be connected to VI if unused. |
| 3 | VI | power_in | This is the positive input voltage power node to the module, referenced to common GND, with an input voltage range of 4.5 V to 14 V. |
| 4 | Inhibit | input | This open-collector/drain-negative logic input referenced to GND disables the module output when driven low and must not have an external pull-up. |
| 5 | VO Adjust | input | A 1% resistor between this pin and GND (pin 1) sets the output voltage above 0.9 V over a set-point range of 0.9 V to 5.5 V, with a resistor temperature stability of 100 ppm/°C or better, and the output defaults to 0.9 V if left open. |
| 6 | VO | power_out | This is the regulated positive power output with respect to the GND node. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | DIP-6 |
| Category | Power Supply Chip |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating free-air temperature | TA | -40 | | 85 | °C | Over VI range | 2 |
| Lead temperature (H suffix) | | | | 260 | °C | 5 seconds | 2 |
| Storage temperature | Tstg | -55 | | 125 | °C | | 2 |
| Input voltage | VI | 4.5 | | 14 | V | | 2 |
| Operating free-air temperature | TA | -40 | | 85 | °C | | 2 |
| Output current | IO | 0 | | 2.25 | A | TA = 85°C, natural convection airflow | 3 |
| Input voltage range | VI | 4.5 | | 14 | V | Over IO range | 3 |
| Set-point voltage tolerance | | | | 2 | % | TA = 25°C | 3 |
| Temperature variation | | | | 0.5 | %VO | -40°C ≤ TA ≤ 85°C | 3 |
| Line regulation | VO | | | 7 | mV | Over VI range | 3 |
| Load regulation | | | | 0.13 | %VO | Over IO range | 3 |
| Total output voltage variation | | | | 3 | %VO | Includes set-point, line, load, -40°C ≤ TA ≤ 85°C | 3 |
| Output voltage adjust range | V(ADJ) | 0.9 | | 5.5 | V | Over IO range | 3 |
| Output voltage ripple | | | | 40 | mVPP | 20-MHz bandwidth | 3 |
| Undervoltage lockout, increasing | UVLO | 4.35 | | 4.5 | V | VI = increasing | 3 |
| Undervoltage lockout, decreasing | UVLO | 3.6 | | 4 | V | VI = decreasing | 3 |
| Input low voltage (VIL) | VIL | -0.2 | | 0.5 | V | Inhibit control (pin 4) | 3 |
| Equivalent series resistance (nonceramic) | | 10 | | | mΩ | Nonceramic | 3 |
| External input capacitance, electrolytic | CI | 100 | | | µF | Electrolytic type (CI) | 3 |
| External output capacitance, nonceramic | CO | | | 330 | µF | Nonceramic type (CO) | 3 |
| External output capacitance, ceramic | CO | | | 220 | µF | Ceramic type (CO) | 3 |
| Track slew rate capability | dVtrack/dt | | | 1 | V/ms | CO ≤ CO(max) | 3 |
| Transient response over/undershoot | | | | 100 | mV | CO = 100 µF, 1 A/µs; load step from 50% to 100% IO | 3 |
## CAD (KiCad official)
- Symbol: `PTH08000WAH`
- Footprint: `Package_DIP:DIP-6_W7.62mm`
- 3D model: DIP-6 (KiCad packages3D, STEP)
- 3D model files: `pth08000wah-etched.step` / `pth08000wah-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pth08000wah.step` / `pth08000wah.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/pth08000w) (20 pp, sha256 `44479cb1240faddf`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pth08000wah-datasheet.pdf)