main
Ray
pt438: laser-etched CAD + chip hero (factory 2.0.0 backfill)
2ae4bb6
PT438
PUOLOP · Battery Management · SOT-23-6L
PT438 from PUOLOP, in a SOT-23-6L. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OD | output | Discharge control MOSFET gate driver. Drives the gate of the discharge-control N-MOSFET; high (~VCC) enables discharge, low (~GND) disables it during over-discharge/over-current/short-circuit protection. VODH = VCC-0.02V typ, VODL = 0.1V typ. |
| 2 | CS | input | Current-sense and charger-detect input. Monitors the voltage between BATT- and GND (across the two series MOSFETs) to detect discharge over-current (VOI1=176mV typ), load short-circuit (VOI2=1.00V typ), and charger connection (VCH). Absolute max VCC-14V to VCC+0.3V. |
| 3 | OC | output | Charge control MOSFET gate driver. Drives the gate of the charge-control N-MOSFET; high (~VCC) enables charging, low (~GND) disables charging during over-charge protection. VOCH = VCC-0.02V typ, VOCL = 0.1V typ. |
| 4 | TD | input | Test pin used to shorten the over-charge detection delay time so factory test cycles are reduced. Normally left unconnected in application (see typical application circuit). |
| 5 | VCC | power_in | Positive supply, connected to the battery positive terminal through a series resistor R1 (typ 100 Ω) with a 0.1 µF decoupling capacitor C1 to GND for charger ripple/disturbance suppression. Operating VCC range 2V to 5V (typ 3.6V); absolute max GND-0.3V to GND+10V. |
| 6 | GND | power_in | Ground reference, connected to the battery negative terminal via the decoupling capacitor node. All internal detection voltages are referenced to this pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PUOLOP |
| Package | SOT-23-6L |
| Category | PMIC |
| Pins | 6 |
CAD (KiCad official)
- Symbol:
PT438 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6L (KiCad packages3D, STEP)
- 3D model files:
pt438-etched.step/pt438-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pt438.step/pt438.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: PUOLOP datasheet (None pp, sha256
e81e24170c67e283, retrieved 2026-08-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PT438
**PUOLOP** · Battery Management · SOT-23-6L
PT438 from PUOLOP, in a SOT-23-6L. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OD | output | Discharge control MOSFET gate driver. Drives the gate of the discharge-control N-MOSFET; high (~VCC) enables discharge, low (~GND) disables it during over-discharge/over-current/short-circuit protection. VODH = VCC-0.02V typ, VODL = 0.1V typ. |
| 2 | CS | input | Current-sense and charger-detect input. Monitors the voltage between BATT- and GND (across the two series MOSFETs) to detect discharge over-current (VOI1=176mV typ), load short-circuit (VOI2=1.00V typ), and charger connection (VCH). Absolute max VCC-14V to VCC+0.3V. |
| 3 | OC | output | Charge control MOSFET gate driver. Drives the gate of the charge-control N-MOSFET; high (~VCC) enables charging, low (~GND) disables charging during over-charge protection. VOCH = VCC-0.02V typ, VOCL = 0.1V typ. |
| 4 | TD | input | Test pin used to shorten the over-charge detection delay time so factory test cycles are reduced. Normally left unconnected in application (see typical application circuit). |
| 5 | VCC | power_in | Positive supply, connected to the battery positive terminal through a series resistor R1 (typ 100 Ω) with a 0.1 µF decoupling capacitor C1 to GND for charger ripple/disturbance suppression. Operating VCC range 2V to 5V (typ 3.6V); absolute max GND-0.3V to GND+10V. |
| 6 | GND | power_in | Ground reference, connected to the battery negative terminal via the decoupling capacitor node. All internal detection voltages are referenced to this pin. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PUOLOP |
| Package | SOT-23-6L |
| Category | PMIC |
| Pins | 6 |
## CAD (KiCad official)
- Symbol: `PT438`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6L (KiCad packages3D, STEP)
- 3D model files: `pt438-etched.step` / `pt438-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pt438.step` / `pt438.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [PUOLOP datasheet](docs/pt438-datasheet.pdf) (None pp, sha256 `e81e24170c67e283`, retrieved 2026-08-17, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pt438-datasheet.pdf)