main
Ray
Publish 0.1.0
e341fcd
PMS150G-S08
PADAUK Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SOP-8-150mil
PMS150G-S08 from PADAUK Tech, in a SOP-8-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Positive supply, operating range 1.8V to 5.5V (absolute maximum 5.5V). |
| 2 | PA7/CIN- | bidirectional | Port A bit 7, programmable input or output with weak pull-up/pull-down, and negative input of the comparator; clear padier bit 7 when used as an analog input, which also disables its wake-up function. |
| 3 | PA6/CIN- | bidirectional | Port A bit 6, programmable input or output with weak pull-up/pull-down, and negative input of the comparator; clear padier bit 6 when used as an analog input, which also disables its wake-up function. |
| 4 | PA5/PRSTB | bidirectional | Port A bit 5 (input or output with weak pull-up/pull-down, or open-drain via code option) or external reset input PRSTB; a 33 ohm series resistor is advised as an input in high-noise systems. |
| 5 | PA3/CIN-/TM2PWM | bidirectional | Port A bit 3, programmable input or output with weak pull-up/pull-down, comparator negative input, and Timer2 output; clear padier bit 3 when used as an analog input. |
| 6 | PA4/CIN+/CIN-/TM2PWM | bidirectional | Port A bit 4, programmable input or output with weak pull-up/pull-down, comparator positive or negative input, and Timer2 output; clear padier bit 4 when used as an analog input. |
| 7 | PA0/INT0/CO | bidirectional | Port A bit 0, programmable input or output with weak pull-up/pull-down, external interrupt 0 triggered on rising and falling edges, and comparator output. |
| 8 | GND | power_in | Ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PADAUK Tech |
| Package | SOP-8-150mil |
| Category | Embedded Processors & Controllers |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 工作电压 | VDD | 1.8 | 5.5 | V | 受限于 LVR 公差 | 11 | |
| 低电压复位公差 | LVR% | -5 | 5 | % | 11 | ||
| 系统时钟(CLK) = IHRC/8 (最大频率) | fSYS | 2 | MHz | VDD ≧ 1.8V | 11 | ||
| 上电复位电压 | VPOR | 1.7 | 1.8 | 1.9 | V | 11 | |
| IO 引脚输出灌电流 | IOL | 19 | 21 | 24 | mA | VDD=5.0V, VOL=0.5V | 11 |
| PA5(开漏输出)输出驱动电流 | IOH | -11 | -13 | mA | VDD=5.0V, VOH=4.5V | 11 | |
| PA5(普通 IO)输出驱动电流 | IOH | -11 | -13 | mA | VDD=5.0V, VOH=4.5V | 11 | |
| 其他 IO 引脚输出驱动电流 | IOH | 0 | -16 | mA | VDD=5.0V, VOH=4.5V | 11 | |
| 输入低电压 | VIL | 0 | 0.1 | VDD | 11 | ||
| 输入高电压 | VIH | 0.7 | VDD | 11 | |||
| 输入电压 | VIN | -0.3 | V | 11 | |||
| 上拉电阻 | RPH | 76 | 84 | 96 | KΩ | 11 | |
| 下拉电阻 | RPL | 66 | 77 | 86 | KΩ | 11 | |
| IHRC 输出频率(校准后) | fIHRC | 15.66 | 16 | 16.34 | MHz | @25oC, VDD =2.0V~5.5V | 11 |
| IHRC 输出频率(校准后) | fIHRC | 15.1 | 16 | 16.9 | MHz | VDD=2.0V~5.5V, -20oC <Ta<70oC | 11 |
| 比较器偏压 | CPos | -20 | 10 | 20 | mV | 12 | |
| 比较器共模输入电压 | CPcm | 0 | V | 12 | |||
| 比较器响应时间 | CPspt | 100 | 500 | ns | 上升沿和下降沿一样 | 12 | |
| 比较器模式改变稳定时间 | CPmc | 2.5 | 7.5 | us | 12 | ||
| 电源电压 | VDD | 1.8 | 5.5 | V | 12 | ||
| 输入电压 | VIN | -0.3 | V | 12 | |||
| 工作温度 | Ta | -20 | 70 | °C | 12 | ||
| 储藏温度 | Tstg | -50 | 125 | °C | 12 | ||
| 结点温度 | Tj | 150 | °C | 12 | |||
| 工作电流 (fSYS=IHRC/16) | IOP | 0.3 | mA | fSYS=IHRC/16=[email protected] | 11 | ||
| 工作电流 (fSYS=ILRC) | IOP | 22 | uA | fSYS=ILRC=[email protected] | 11 | ||
| 掉电模式消耗电流 | IPD | 1 | uA | fSYS= 0Hz, VDD =3.3V | 11 | ||
| 省电模式消耗电流 | IPS | 3 | uA | VDD =3.3V;Bandgap, LVR, IHRC 关闭, ILRC 打开 | 11 | ||
| 脚位的引入电流 | IINJ (PIN) | 1 | mA | VDD +0.3≧VIN≧ -0.3 | 11 | ||
| ILRC 输出频率 | fILRC | 57 | KHz | VDD =5.0V, -20oC <Ta<70oC | 11 | ||
| 中断脉冲宽度 | tINT | 30 | ns | VDD = 5.0V | 11 | ||
| 数据存储器数据保存电压 | VDR | 1.5 | V | 关机模式 | 11 | ||
| 看门狗超时溢出时间 (misc[1:0]=00,默认) | tWDT | 8 | k ILRC 时钟周期 | misc[1:0]=00(默认) | 12 | ||
| 看门狗超时溢出时间 (misc[1:0]=01) | tWDT | 16 | k ILRC 时钟周期 | misc[1:0]=01 | 12 | ||
| 看门狗超时溢出时间 (misc[1:0]=10) | tWDT | 64 | k ILRC 时钟周期 | misc[1:0]=10 | 12 | ||
| 看门狗超时溢出时间 (misc[1:0]=11) | tWDT | 256 | k ILRC 时钟周期 | misc[1:0]=11 | 12 | ||
| 系统开机时间(快速开机) | tSBP | 850 | us | @ VDD =5V | 12 | ||
| 系统开机时间(正常开机) | tSBP | 51 | ms | @ VDD =5V | 12 | ||
| 快速唤醒下的唤醒时间 (misc.5=1) | tWUP | 32 | TILRC | TILRC 为 ILRC 振荡周期 | 12 | ||
| 普通唤醒下的唤醒时间 (misc.5=0) | tWUP | 2048 | TILRC | TILRC 为 ILRC 振荡周期 | 12 | ||
| 外部复位脉冲宽度 | tRST | 120 | us | @ VDD =5V | 12 | ||
| 比较器电流消耗 | CPcs | 20 | uA | VDD = 3.3V | 12 |
CAD (KiCad official)
- Symbol:
PMS150G-S08 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8-150mil (KiCad packages3D, STEP)
- 3D model files:
pms150g-s08-etched.step/pms150g-s08-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pms150g-s08.step/pms150g-s08.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: PADAUK Tech datasheet (68 pp, sha256
1f9d9e89b75b90aa, retrieved 2026-11-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PMS150G-S08
**PADAUK Tech** · Microcontroller Units (MCUs/MPUs/SOCs) · SOP-8-150mil
PMS150G-S08 from PADAUK Tech, in a SOP-8-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Positive supply, operating range 1.8V to 5.5V (absolute maximum 5.5V). |
| 2 | PA7/CIN- | bidirectional | Port A bit 7, programmable input or output with weak pull-up/pull-down, and negative input of the comparator; clear padier bit 7 when used as an analog input, which also disables its wake-up function. |
| 3 | PA6/CIN- | bidirectional | Port A bit 6, programmable input or output with weak pull-up/pull-down, and negative input of the comparator; clear padier bit 6 when used as an analog input, which also disables its wake-up function. |
| 4 | PA5/PRSTB | bidirectional | Port A bit 5 (input or output with weak pull-up/pull-down, or open-drain via code option) or external reset input PRSTB; a 33 ohm series resistor is advised as an input in high-noise systems. |
| 5 | PA3/CIN-/TM2PWM | bidirectional | Port A bit 3, programmable input or output with weak pull-up/pull-down, comparator negative input, and Timer2 output; clear padier bit 3 when used as an analog input. |
| 6 | PA4/CIN+/CIN-/TM2PWM | bidirectional | Port A bit 4, programmable input or output with weak pull-up/pull-down, comparator positive or negative input, and Timer2 output; clear padier bit 4 when used as an analog input. |
| 7 | PA0/INT0/CO | bidirectional | Port A bit 0, programmable input or output with weak pull-up/pull-down, external interrupt 0 triggered on rising and falling edges, and comparator output. |
| 8 | GND | power_in | Ground. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PADAUK Tech |
| Package | SOP-8-150mil |
| Category | Embedded Processors & Controllers |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 工作电压 | VDD | 1.8 | | 5.5 | V | 受限于 LVR 公差 | 11 |
| 低电压复位公差 | LVR% | -5 | | 5 | % | | 11 |
| 系统时钟(CLK) = IHRC/8 (最大频率) | fSYS | | | 2 | MHz | VDD ≧ 1.8V | 11 |
| 上电复位电压 | VPOR | 1.7 | 1.8 | 1.9 | V | | 11 |
| IO 引脚输出灌电流 | IOL | 19 | 21 | 24 | mA | VDD=5.0V, VOL=0.5V | 11 |
| PA5(开漏输出)输出驱动电流 | IOH | -11 | | -13 | mA | VDD=5.0V, VOH=4.5V | 11 |
| PA5(普通 IO)输出驱动电流 | IOH | -11 | | -13 | mA | VDD=5.0V, VOH=4.5V | 11 |
| 其他 IO 引脚输出驱动电流 | IOH | 0 | | -16 | mA | VDD=5.0V, VOH=4.5V | 11 |
| 输入低电压 | VIL | 0 | | 0.1 | VDD | | 11 |
| 输入高电压 | VIH | 0.7 | | | VDD | | 11 |
| 输入电压 | VIN | -0.3 | | | V | | 11 |
| 上拉电阻 | RPH | 76 | 84 | 96 | KΩ | | 11 |
| 下拉电阻 | RPL | 66 | 77 | 86 | KΩ | | 11 |
| IHRC 输出频率(校准后) | fIHRC | 15.66 | 16 | 16.34 | MHz | @25oC, VDD =2.0V~5.5V | 11 |
| IHRC 输出频率(校准后) | fIHRC | 15.1 | 16 | 16.9 | MHz | VDD=2.0V~5.5V, -20oC <Ta<70oC | 11 |
| 比较器偏压 | CPos | -20 | 10 | 20 | mV | | 12 |
| 比较器共模输入电压 | CPcm | 0 | | | V | | 12 |
| 比较器响应时间 | CPspt | 100 | | 500 | ns | 上升沿和下降沿一样 | 12 |
| 比较器模式改变稳定时间 | CPmc | 2.5 | | 7.5 | us | | 12 |
| 电源电压 | VDD | 1.8 | | 5.5 | V | | 12 |
| 输入电压 | VIN | -0.3 | | | V | | 12 |
| 工作温度 | Ta | -20 | | 70 | °C | | 12 |
| 储藏温度 | Tstg | -50 | | 125 | °C | | 12 |
| 结点温度 | Tj | | | 150 | °C | | 12 |
| 工作电流 (fSYS=IHRC/16) | IOP | | 0.3 | | mA | fSYS=IHRC/[email protected] | 11 |
| 工作电流 (fSYS=ILRC) | IOP | | 22 | | uA | [email protected] | 11 |
| 掉电模式消耗电流 | IPD | | 1 | | uA | fSYS= 0Hz, VDD =3.3V | 11 |
| 省电模式消耗电流 | IPS | | 3 | | uA | VDD =3.3V;Bandgap, LVR, IHRC 关闭, ILRC 打开 | 11 |
| 脚位的引入电流 | IINJ (PIN) | | 1 | | mA | VDD +0.3≧VIN≧ -0.3 | 11 |
| ILRC 输出频率 | fILRC | | 57 | | KHz | VDD =5.0V, -20oC <Ta<70oC | 11 |
| 中断脉冲宽度 | tINT | | 30 | | ns | VDD = 5.0V | 11 |
| 数据存储器数据保存电压 | VDR | | 1.5 | | V | 关机模式 | 11 |
| 看门狗超时溢出时间 (misc[1:0]=00,默认) | tWDT | | 8 | | k ILRC 时钟周期 | misc[1:0]=00(默认) | 12 |
| 看门狗超时溢出时间 (misc[1:0]=01) | tWDT | | 16 | | k ILRC 时钟周期 | misc[1:0]=01 | 12 |
| 看门狗超时溢出时间 (misc[1:0]=10) | tWDT | | 64 | | k ILRC 时钟周期 | misc[1:0]=10 | 12 |
| 看门狗超时溢出时间 (misc[1:0]=11) | tWDT | | 256 | | k ILRC 时钟周期 | misc[1:0]=11 | 12 |
| 系统开机时间(快速开机) | tSBP | | 850 | | us | @ VDD =5V | 12 |
| 系统开机时间(正常开机) | tSBP | | 51 | | ms | @ VDD =5V | 12 |
| 快速唤醒下的唤醒时间 (misc.5=1) | tWUP | | 32 | | TILRC | TILRC 为 ILRC 振荡周期 | 12 |
| 普通唤醒下的唤醒时间 (misc.5=0) | tWUP | | 2048 | | TILRC | TILRC 为 ILRC 振荡周期 | 12 |
| 外部复位脉冲宽度 | tRST | | 120 | | us | @ VDD =5V | 12 |
| 比较器电流消耗 | CPcs | | 20 | | uA | VDD = 3.3V | 12 |
## CAD (KiCad official)
- Symbol: `PMS150G-S08`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOP-8-150mil (KiCad packages3D, STEP)
- 3D model files: `pms150g-s08-etched.step` / `pms150g-s08-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pms150g-s08.step` / `pms150g-s08.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [PADAUK Tech datasheet](docs/pms150g-s08-datasheet.pdf) (68 pp, sha256 `1f9d9e89b75b90aa`, retrieved 2026-11-05, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pms150g-s08-datasheet.pdf)