main
Ray Publish 0.1.0 2f02201

PM25LQ010B-SCE

ISSI(Integrated Silicon Solution) · NOR FLASH · SOIC-8

PM25LQ010B-SCE from ISSI(Integrated Silicon Solution), in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CE# input Chip Enable: when high the device is deselected, outputs are high impedance and it enters low-power standby; it must go low to accept an instruction.
2 SO (IO1) bidirectional Serial Data Output in standard SPI, becoming a bidirectional IO1 pin in Dual and Quad SPI modes, with data read on the falling edge of SCK.
3 WP# (IO2) bidirectional Write Protect that protects the Status Register in conjunction with the SRWD bit, becoming IO2 (write-protect function unavailable) when the QE bit is set to 1.
4 GND power_in Ground reference for the device, connected to ground relative to Vcc.
5 SI (IO0) bidirectional Serial Data Input for instructions, addresses and data on the rising edge of SCK, becoming bidirectional IO0 in Dual and Quad SPI modes.
6 SCK input Serial Data Clock providing synchronized timing for input and output operations.
7 HOLD# (IO3) bidirectional Active-low Hold that pauses serial communication without resetting the sequence, becoming IO3 (hold function unavailable) when the QE bit is set to 1.
8 Vcc power_in Device core power supply, with a single 2.3V to 3.6V supply range.

Key specifications

Parameter Value
Manufacturer ISSI(Integrated Silicon Solution)
Package SOIC-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage Temperature -65 150 °C 54
Lead-free Package Soldering Temperature 260 °C 3 Seconds 54
Input Voltage with Respect to Ground on All Pins -0.5 V upper limit printed as VCC + 0.5V 54
All Output Voltage with Respect to Ground -0.5 V upper limit printed as VCC + 0.5V 54
VCC Supply Voltage VCC -0.5 6 V 54
Operating Temperature -40 85 °C 54
VCC Power Supply VCC 2.3 3.3 3.6 V 2.3V (VMIN), 3.6V (VMAX); 3.3V (Typ) 54
VCC Active Read Current ICC1 10 15 mA VCC = VMAX at 33MHz, SO = Open 54
VCC Program/Erase Current ICC2 15 30 mA VCC = VMAX at 33MHz, SO = Open 54
VCC Standby Current CMOS ISB1 8 50 µA VCC = VMAX, CE# = VCC 54
Deep power down current ISB2 5 20 µA VCC = VMAX, CE# = VCC 54
Input Leakage Current ILI 1 µA VIN = 0V to VCC 54
Output Leakage Current ILO 1 µA VIN = 0V to VCC 54
Output Low Voltage VOL 0.2 V VMIN < VCC < VMAX, IOL = 100 µA 54
Clock Frequency for fast read mode fCT 0 104 MHz 56
Clock Frequency for read mode fC 0 33 MHz 56
Input Rise Time tRI 8 ns 56
Input Fall Time tFI 8 ns 56
SCK High Time tCKH 4 ns 56
SCK Low Time tCKL 4 ns 56
CE# High Time tCEH 7 ns 56
CE# Setup Time tCS 10 ns 56
CE# Hold Time tCH 5 ns 56
Data In Setup Time tDS 2 ns 56
Data in Hold Time tDH 2 ns 56
Hold Setup Time tHS 15 ns 56
Hold Time tHD 15 ns 56
Output Valid tV 8 ns 56
Output Hold Time tOH 2 ns 56
Output Disable Time tDIS 8 ns 56
HOLD Active Setup Time relative to SCK tHLCH 5 ns 56
HOLD Active Hold Time relative to SCK tCHHH 5 ns 56
HOLD Not Active Setup Time relative to SCK tHHCH 5 ns 56
HOLD Not Active Hold Time relative to SCK tCHHL 5 ns 56
HOLD to Output Low Z tLZ 12 ns 56
HOLD to Output High Z tHZ 12 ns 56
Sector Erase Time (4Kbyte) tEC 70 300 ms 56
Block Erase Time (32Kbyte) tEC 130 500 ms 56
Block Erase time (64Kbyte) tEC 200 1000 ms 56
Chip Erase Time 1Mb tEC 0.4 1.5 s 1Mb 56
Page Program Time tPP 0.5 1 ms 56
Release deep power down tres1 3 µs 56
Deep power down tDP 3 µs 56
Write Status Register time tW 2 10 ms 56
Suspend to read ready tSUS 100 µs 56
Software Reset cover time tSRST 100 µs 56
Vcc(min) to CE# Low tVCE 1 ms 58
Power-up time delay to write instruction tPUW 1 10 ms 58
Byte Program Time 8 25 µs From writing program command to program completion 59
Endurance 100000 Cycles JEDEC Standard A117 59
Data Retention 20 Years JEDEC Standard A103 59
ESD, Human Body Model 2000 Volts JEDEC Standard A114 59
ESD, Machine Model 200 Volts JEDEC Standard A115 59

CAD (KiCad official)

  • Symbol: PM25LQ010B-SCE
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: pm25lq010b-sce-etched.step / pm25lq010b-sce-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pm25lq010b-sce.step / pm25lq010b-sce.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: ISSI(Integrated Silicon Solution) datasheet (62 pp, sha256 b48612526f579e06, retrieved 2026-10-31, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF