main
Ray
pl5500: specified limits as data (metadata.characteristics, 20 rows from the datasheet)
f55868f
PL5500
POWLICON · DC-DC Converters · QFN-32-EP(4x4)
PL5500 from POWLICON, in a QFN-32-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VADJ | input | Programs the voltage reference on VREF using a 0-2 V analog voltage or PWM signal. Tying VADJ to VDD forces VREF to a constant 2 V. |
| 2 | IADJ | input | Programs the current-limit reference on IREF using a 0-2 V analog voltage or PWM signal. Tying IADJ to VDD forces IREF to 2 V. |
| 3 | VSET | bidirectional | In charge mode (OTG low): a resistor from VSET to GND selects battery cell full-charge voltage (4.2/4.35/4.4/4.5 V). In discharge mode (OTG > 1.2 V): VSET outputs a voltage proportional to V(CSP2)-V(CSN2) for host monitoring of discharge current. |
| 4 | IREF | passive | Reference-voltage node for the input and output current-limit loops. Typically bypassed with a small capacitor to GND. |
| 5 | VREF | passive | Reference-voltage node for the voltage-control loop (2 V in discharge, 1.8 V in charge when VADJ = VDD). Typically bypassed to GND. |
| 6 | BRCOM | output | Battery internal-resistance compensation output. Voltage on this pin is proportional to V(CSP1)-V(CSN1) so the host can monitor charging current. |
| 7 | MODE | input | CCM/DCM mode select. Float (weak internal pull-up) selects DCM at light load; tie to GND to force CCM. |
| 8 | STAT | output | Status output. Reports charging status when OTG = Low, and functions as a PGOOD (power-good) indicator when OTG = High. |
| 9 | FREQ | input | Sets switching frequency: tie to GND for 150 kHz, tie to VDD for 300 kHz, or use a resistor divider between VDD/GND for 600 kHz (0.4-0.85 V) or 1200 kHz (0.85-1.8 V). |
| 10 | COMP | passive | Error-amplifier output / loop-compensation node. External RC network to GND sets loop dynamics. |
| 11 | VREG | input | Programs VBUS regulation voltage via a resistor divider. During heavy charging, when VBUS falls near the VREG setpoint the VREG loop takes over and reduces charging current. Not active in discharge mode. |
| 12 | FB2 | input | VBUS voltage feedback in discharge mode. A resistor divider from VBUS to GND sets the regulated VBUS voltage (VFB2 regulation = 2 V). |
| 13 | CSN2 | input | Negative input of the output (VBUS-side) current-sense amplifier. Max V(CSP2)-V(CSN2) is 0.6 V. |
| 14 | CSP2 | input | Positive input of the output (VBUS-side) current-sense amplifier. Max V(CSP2)-V(CSN2) is 0.6 V. |
| 15 | VBUS | power_in | VBUS power rail (3.6-32 V operating, 40 V abs max). Sense/supply for the output-side of the buck-boost stage. |
| 16 | HG2 | output | High-side gate drive 2 (VBUS-side high-side MOSFET). Integrated 2 A driver, referenced to SW2, powered from BST2. |
| 17 | BST2 | passive | Bootstrap capacitor node for HG2. Connect capacitor from BST2 to SW2; abs max BST2-to-SW2 = 7 V. |
| 18 | SW2 | passive | Switching node 2 (VBUS-side inductor terminal / bootstrap return). Abs max -0.3 V to 40 V. |
| 19 | LG2 | output | Low-side gate drive 2 (VBUS-side low-side MOSFET). Integrated 2 A driver referenced to GND, powered from VCC. |
| 20 | VCC | power_in | 5.0 V supply for the high-side and low-side gate drivers. Bypass to GND with a low-ESR capacitor. |
| 21 | LG1 | output | Low-side gate drive 1 (VBAT-side low-side MOSFET). Integrated 2 A driver referenced to GND, powered from VCC. |
| 22 | SW1 | passive | Switching node 1 (VBAT-side inductor terminal / bootstrap return). Abs max -0.3 V to 40 V. |
| 23 | BST1 | passive | Bootstrap capacitor node for HG1. Connect capacitor from BST1 to SW1; abs max BST1-to-SW1 = 7 V. |
| 24 | HG1 | output | High-side gate drive 1 (VBAT-side high-side MOSFET). Integrated 2 A driver, referenced to SW1, powered from BST1. |
| 25 | VBAT | power_in | Battery/input power rail (3.6-32 V operating, 40 V abs max). Also acts as output rail during OTG discharge operation. |
| 26 | CSP1 | input | Positive input of the input/battery-side current-sense amplifier. Max V(CSP1)-V(CSN1) is 0.6 V. |
| 27 | CSN1 | input | Negative input of the input/battery-side current-sense amplifier. Max V(CSP1)-V(CSN1) is 0.6 V. |
| 28 | EN | input | Enable input. Logic high enables the converter; logic low disables the entire PL5500. Weak internal pull-up; threshold ≈1.2 V with 200 mV hysteresis. |
| 29 | CELLS | input | Battery cell-count programming input. Resistor divider between VDD and GND sets 1-6 cells per V(CELLS) bins (0-0.9V=1, 4.5-5.5V=2, 0.9-1.8V=3, 1.8-2.7V=4, 2.7-3.6V=5, 3.6-4.5V=6). |
| 30 | OTG | input | Direction/mode select. Tie to GND for battery charging mode; drive above 1.2 V (e.g. to MODE) for battery discharging (OTG) mode. Hysteresis 200 mV. |
| 31 | TS | input | Battery temperature-sense input (NTC thermistor divider). Used for JEITA-style thermal qualification of charging. |
| 32 | VDD | power_in | 5.4 V internal LDO output that powers the PL5500 control core. Bypass to GND with a low-ESR capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | POWLICON |
| Package | QFN-32-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 32 |
Ordering variants
Same part, different packaging or reel option.
PL5500IQN32A
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VBAT, VBUS, CSN1, CSN2, CSP1, CSP2, SW1, SW2 voltage | -0.3 | 40 | V | 4 | |||
| HG1, BST1 to SW1 voltage | -0.3 | 7 | V | 4 | |||
| HG2, BST2 to SW2 voltage | -0.3 | 7 | V | 4 | |||
| LG1, LG2, VCC to GND voltage | -0.3 | 7 | V | 4 | |||
| CSP1 to CSN1 voltage | -0.3 | 0.6 | V | 4 | |||
| CSP2 to CSN2 voltage | -0.3 | 0.6 | V | 4 | |||
| VBAT to CSP1, CSN1 voltage | -0.3 | 0.6 | V | 4 | |||
| VBUS to CSP2, CSN2 voltage | -0.3 | 0.6 | V | 4 | |||
| Other Pins to GND voltage | -0.3 | 6 | V | 4 | |||
| Storage Temperature Range | TST | -65 | 150 | °C | 4 | ||
| Junction Temperature | TJ | 150 | °C | 4 | |||
| Lead Temperature | TL | 260 | °C | 4 | |||
| ESD HBM | VESD | 2 | kV | Human body model | 4 | ||
| Input Voltages VBAT, VBUS | 3.6 | 32 | V | 4 | |||
| Operating junction temperature range | TJ | -40 | 125 | °C | 4 | ||
| VBAT Battery voltage | VBAT | 3.6 | 32 | V | 5 | ||
| VBUS Bus line voltage | VBUS | 3.6 | 32 | V | 5 | ||
| Operation Threshold (EN) | VEN_UV | 1.1 | 1.2 | 1.3 | V | 5 | |
| Junction to ambient thermal resistance | θJA | 44 | °C/W | 4 | |||
| Junction to case thermal resistance | θJC | 9 | °C/W | 4 |
CAD (KiCad official)
- Symbol:
PL5500 - Footprint:
Package_DFN_QFN:QFN-32-1EP_4x4mm_P0.4mm_EP2.9x2.9mm - 3D model: QFN-32-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
pl5500-etched.step/pl5500-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pl5500.step/pl5500.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: POWLICON datasheet (19 pp, sha256
351bf4738852f535, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PL5500
**POWLICON** · DC-DC Converters · QFN-32-EP(4x4)
PL5500 from POWLICON, in a QFN-32-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VADJ | input | Programs the voltage reference on VREF using a 0-2 V analog voltage or PWM signal. Tying VADJ to VDD forces VREF to a constant 2 V. |
| 2 | IADJ | input | Programs the current-limit reference on IREF using a 0-2 V analog voltage or PWM signal. Tying IADJ to VDD forces IREF to 2 V. |
| 3 | VSET | bidirectional | In charge mode (OTG low): a resistor from VSET to GND selects battery cell full-charge voltage (4.2/4.35/4.4/4.5 V). In discharge mode (OTG > 1.2 V): VSET outputs a voltage proportional to V(CSP2)-V(CSN2) for host monitoring of discharge current. |
| 4 | IREF | passive | Reference-voltage node for the input and output current-limit loops. Typically bypassed with a small capacitor to GND. |
| 5 | VREF | passive | Reference-voltage node for the voltage-control loop (2 V in discharge, 1.8 V in charge when VADJ = VDD). Typically bypassed to GND. |
| 6 | BRCOM | output | Battery internal-resistance compensation output. Voltage on this pin is proportional to V(CSP1)-V(CSN1) so the host can monitor charging current. |
| 7 | MODE | input | CCM/DCM mode select. Float (weak internal pull-up) selects DCM at light load; tie to GND to force CCM. |
| 8 | STAT | output | Status output. Reports charging status when OTG = Low, and functions as a PGOOD (power-good) indicator when OTG = High. |
| 9 | FREQ | input | Sets switching frequency: tie to GND for 150 kHz, tie to VDD for 300 kHz, or use a resistor divider between VDD/GND for 600 kHz (0.4-0.85 V) or 1200 kHz (0.85-1.8 V). |
| 10 | COMP | passive | Error-amplifier output / loop-compensation node. External RC network to GND sets loop dynamics. |
| 11 | VREG | input | Programs VBUS regulation voltage via a resistor divider. During heavy charging, when VBUS falls near the VREG setpoint the VREG loop takes over and reduces charging current. Not active in discharge mode. |
| 12 | FB2 | input | VBUS voltage feedback in discharge mode. A resistor divider from VBUS to GND sets the regulated VBUS voltage (VFB2 regulation = 2 V). |
| 13 | CSN2 | input | Negative input of the output (VBUS-side) current-sense amplifier. Max V(CSP2)-V(CSN2) is 0.6 V. |
| 14 | CSP2 | input | Positive input of the output (VBUS-side) current-sense amplifier. Max V(CSP2)-V(CSN2) is 0.6 V. |
| 15 | VBUS | power_in | VBUS power rail (3.6-32 V operating, 40 V abs max). Sense/supply for the output-side of the buck-boost stage. |
| 16 | HG2 | output | High-side gate drive 2 (VBUS-side high-side MOSFET). Integrated 2 A driver, referenced to SW2, powered from BST2. |
| 17 | BST2 | passive | Bootstrap capacitor node for HG2. Connect capacitor from BST2 to SW2; abs max BST2-to-SW2 = 7 V. |
| 18 | SW2 | passive | Switching node 2 (VBUS-side inductor terminal / bootstrap return). Abs max -0.3 V to 40 V. |
| 19 | LG2 | output | Low-side gate drive 2 (VBUS-side low-side MOSFET). Integrated 2 A driver referenced to GND, powered from VCC. |
| 20 | VCC | power_in | 5.0 V supply for the high-side and low-side gate drivers. Bypass to GND with a low-ESR capacitor. |
| 21 | LG1 | output | Low-side gate drive 1 (VBAT-side low-side MOSFET). Integrated 2 A driver referenced to GND, powered from VCC. |
| 22 | SW1 | passive | Switching node 1 (VBAT-side inductor terminal / bootstrap return). Abs max -0.3 V to 40 V. |
| 23 | BST1 | passive | Bootstrap capacitor node for HG1. Connect capacitor from BST1 to SW1; abs max BST1-to-SW1 = 7 V. |
| 24 | HG1 | output | High-side gate drive 1 (VBAT-side high-side MOSFET). Integrated 2 A driver, referenced to SW1, powered from BST1. |
| 25 | VBAT | power_in | Battery/input power rail (3.6-32 V operating, 40 V abs max). Also acts as output rail during OTG discharge operation. |
| 26 | CSP1 | input | Positive input of the input/battery-side current-sense amplifier. Max V(CSP1)-V(CSN1) is 0.6 V. |
| 27 | CSN1 | input | Negative input of the input/battery-side current-sense amplifier. Max V(CSP1)-V(CSN1) is 0.6 V. |
| 28 | EN | input | Enable input. Logic high enables the converter; logic low disables the entire PL5500. Weak internal pull-up; threshold ≈1.2 V with 200 mV hysteresis. |
| 29 | CELLS | input | Battery cell-count programming input. Resistor divider between VDD and GND sets 1-6 cells per V(CELLS) bins (0-0.9V=1, 4.5-5.5V=2, 0.9-1.8V=3, 1.8-2.7V=4, 2.7-3.6V=5, 3.6-4.5V=6). |
| 30 | OTG | input | Direction/mode select. Tie to GND for battery charging mode; drive above 1.2 V (e.g. to MODE) for battery discharging (OTG) mode. Hysteresis 200 mV. |
| 31 | TS | input | Battery temperature-sense input (NTC thermistor divider). Used for JEITA-style thermal qualification of charging. |
| 32 | VDD | power_in | 5.4 V internal LDO output that powers the PL5500 control core. Bypass to GND with a low-ESR capacitor. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | POWLICON |
| Package | QFN-32-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 32 |
## Ordering variants
Same part, different packaging or reel option.
- `PL5500IQN32A`
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VBAT, VBUS, CSN1, CSN2, CSP1, CSP2, SW1, SW2 voltage | | -0.3 | | 40 | V | | 4 |
| HG1, BST1 to SW1 voltage | | -0.3 | | 7 | V | | 4 |
| HG2, BST2 to SW2 voltage | | -0.3 | | 7 | V | | 4 |
| LG1, LG2, VCC to GND voltage | | -0.3 | | 7 | V | | 4 |
| CSP1 to CSN1 voltage | | -0.3 | | 0.6 | V | | 4 |
| CSP2 to CSN2 voltage | | -0.3 | | 0.6 | V | | 4 |
| VBAT to CSP1, CSN1 voltage | | -0.3 | | 0.6 | V | | 4 |
| VBUS to CSP2, CSN2 voltage | | -0.3 | | 0.6 | V | | 4 |
| Other Pins to GND voltage | | -0.3 | | 6 | V | | 4 |
| Storage Temperature Range | TST | -65 | | 150 | °C | | 4 |
| Junction Temperature | TJ | | | 150 | °C | | 4 |
| Lead Temperature | TL | | | 260 | °C | | 4 |
| ESD HBM | VESD | | | 2 | kV | Human body model | 4 |
| Input Voltages VBAT, VBUS | | 3.6 | | 32 | V | | 4 |
| Operating junction temperature range | TJ | -40 | | 125 | °C | | 4 |
| VBAT Battery voltage | VBAT | 3.6 | | 32 | V | | 5 |
| VBUS Bus line voltage | VBUS | 3.6 | | 32 | V | | 5 |
| Operation Threshold (EN) | VEN_UV | 1.1 | 1.2 | 1.3 | V | | 5 |
| Junction to ambient thermal resistance | θJA | | 44 | | °C/W | | 4 |
| Junction to case thermal resistance | θJC | | 9 | | °C/W | | 4 |
## CAD (KiCad official)
- Symbol: `PL5500`
- Footprint: `Package_DFN_QFN:QFN-32-1EP_4x4mm_P0.4mm_EP2.9x2.9mm`
- 3D model: QFN-32-EP(4x4) (KiCad packages3D, STEP)
- 3D model files: `pl5500-etched.step` / `pl5500-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pl5500.step` / `pl5500.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [POWLICON datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588917961151426560) (19 pp, sha256 `351bf4738852f535`, retrieved 2026-08-17, tier: lcsc)
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pl5500-datasheet.pdf)