main
Ray
Publish 0.1.0
275783d
PJ9500M28SE
PJSEMI · Linear Voltage Regulators (LDO) · SOT-23-5
PJ9500M28SE from PJSEMI, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input pin supplying the LDO; the input range is 1.8V to 6V, and a 1µF ceramic capacitor is recommended between VIN and GND. |
| 2 | GND | power_in | Ground reference pin for the regulator; the input and output capacitors should be placed as close as possible to the device. |
| 3 | EN | input | Chip enable, active high, with high impedance; the part turns on above VIH (1.2V min) and off below VIL (0.9V max), and the pin is internally pulled to GND through 1 MΩ. |
| 4 | NC | unconnected | No internal connection on this pin (printed as 'NO Connected' in the datasheet). |
| 5 | VOUT | power_out | Regulated output voltage for the PJ9500M28 (2.8V nominal, ±2% accuracy), with a maximum output current of 500mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PJSEMI |
| Package | SOT-23-5 |
| Category | Power Management |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 1.8 | 6 | V | 7 | ||
| Output Voltage Accuracy | ΔVOUT | -2 | 2 | % | VIN=5V, IOUT=10mA | 7 | |
| Line Regulation | ΔVLINE | 1 | 3 | mV | VIN=(VOUT+2V)~7V, IOUT=1mA | 7 | |
| Load Regulation | ΔVLOAD | 0.1 | 0.2 | mV/mA | VOUT=4V, IOUT=1~200mA | 7 | |
| Short Circuit Current | ISHORT | 120 | 150 | mA | VEN=VIN, VOUT Short to GND | 7 | |
| EN Input Threshold Logic Low | VIL | 0.9 | V | 7 | |||
| EN Input Threshold Logic High | VIH | 1.2 | V | 7 | |||
| Supply Voltage | 1.8 | 6 | V | 6 | |||
| Maximum Output Current | 500 | mA | 6 | ||||
| Operating Ambient Temperature | -40 | 125 | °C | 6 | |||
| VIN, VEN to GND Voltage (VIN) | VIN | -0.3 | 6 | V | 6 | ||
| VIN, VEN to GND Voltage (VEN) | VEN | -0.3 | 6 | V | 6 | ||
| VOUT to VIN Voltage | -0.3 | 5 | V | 6 | |||
| Maximum Load Current | 500 | mA | 6 | ||||
| Power Dissipation | 250 | mW | SOT-23-5 package | 6 | |||
| Operating Ambient Temperature | -40 | 125 | °C | 6 | |||
| Storage Temperature Range | -40 | 150 | °C | 6 | |||
| Lead Temperature | 300 | °C | 10S | 6 | |||
| ESD Voltage HBM | HBM | 4 | KV | HBM | 6 | ||
| ESD Voltage CDM | CDM | 200 | V | CDM | 6 | ||
| Thermal Resistance, Junction-to-Ambient | 400 | °C/W | SOT-23-5 package | 6 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
PJ9500M28SE - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.92 mm, terminals on the pads, 1.1 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
pj9500m28se-etched.step/pj9500m28se-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pj9500m28se.step/pj9500m28se.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: PJSEMI datasheet (16 pp, sha256
d7709c00ce45adff, retrieved 2026-11-12, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
# PJ9500M28SE
**PJSEMI** · Linear Voltage Regulators (LDO) · SOT-23-5
PJ9500M28SE from PJSEMI, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input pin supplying the LDO; the input range is 1.8V to 6V, and a 1µF ceramic capacitor is recommended between VIN and GND. |
| 2 | GND | power_in | Ground reference pin for the regulator; the input and output capacitors should be placed as close as possible to the device. |
| 3 | EN | input | Chip enable, active high, with high impedance; the part turns on above VIH (1.2V min) and off below VIL (0.9V max), and the pin is internally pulled to GND through 1 MΩ. |
| 4 | NC | unconnected | No internal connection on this pin (printed as 'NO Connected' in the datasheet). |
| 5 | VOUT | power_out | Regulated output voltage for the PJ9500M28 (2.8V nominal, ±2% accuracy), with a maximum output current of 500mA. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PJSEMI |
| Package | SOT-23-5 |
| Category | Power Management |
| Pins | 5 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 1.8 | | 6 | V | | 7 |
| Output Voltage Accuracy | ΔVOUT | -2 | | 2 | % | VIN=5V, IOUT=10mA | 7 |
| Line Regulation | ΔVLINE | | 1 | 3 | mV | VIN=(VOUT+2V)~7V, IOUT=1mA | 7 |
| Load Regulation | ΔVLOAD | | 0.1 | 0.2 | mV/mA | VOUT=4V, IOUT=1~200mA | 7 |
| Short Circuit Current | ISHORT | | 120 | 150 | mA | VEN=VIN, VOUT Short to GND | 7 |
| EN Input Threshold Logic Low | VIL | | | 0.9 | V | | 7 |
| EN Input Threshold Logic High | VIH | 1.2 | | | V | | 7 |
| Supply Voltage | | 1.8 | | 6 | V | | 6 |
| Maximum Output Current | | | | 500 | mA | | 6 |
| Operating Ambient Temperature | | -40 | | 125 | °C | | 6 |
| VIN, VEN to GND Voltage (VIN) | VIN | -0.3 | | 6 | V | | 6 |
| VIN, VEN to GND Voltage (VEN) | VEN | -0.3 | | 6 | V | | 6 |
| VOUT to VIN Voltage | | -0.3 | | 5 | V | | 6 |
| Maximum Load Current | | | | 500 | mA | | 6 |
| Power Dissipation | | | | 250 | mW | SOT-23-5 package | 6 |
| Operating Ambient Temperature | | -40 | | 125 | °C | | 6 |
| Storage Temperature Range | | -40 | | 150 | °C | | 6 |
| Lead Temperature | | | | 300 | °C | 10S | 6 |
| ESD Voltage HBM | HBM | | | 4 | KV | HBM | 6 |
| ESD Voltage CDM | CDM | | | 200 | V | CDM | 6 |
| Thermal Resistance, Junction-to-Ambient | | | | 400 | °C/W | SOT-23-5 package | 6 |
## CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol: `PJ9500M28SE`
- Footprint: `Package_TO_SOT_SMD:SOT-23-5`
- 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.92 mm, terminals on the pads, 1.1 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `pj9500m28se-etched.step` / `pj9500m28se-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pj9500m28se.step` / `pj9500m28se.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [PJSEMI datasheet](docs/pj9500m28se-datasheet.pdf) (16 pp, sha256 `d7709c00ce45adff`, retrieved 2026-11-12, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
[Datasheet PDF](docs/pj9500m28se-datasheet.pdf)