Generated by kicad-footprint-generator · KiCad file format 20260206
PIC18F97J60T-I
Microchip Tech · Pre-ordered MCUs · TQFP-100(12x12)
PIC18F97J60T-I from Microchip Tech, in a TQFP-100(12x12). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RH2/A18 | bidirectional | PORTH digital I/O (Schmitt Trigger) or external memory address line 18. |
| 2 | RH3/A19 | bidirectional | PORTH digital I/O (Schmitt Trigger) or external memory address line 19. |
| 3 | RE1/AD9/WR/P2C | bidirectional | PORTE digital I/O, external memory address/data 9, Parallel Slave Port write control input, or ECCP2 PWM output C. |
| 4 | RE0/AD8/RD/P2D | bidirectional | PORTE digital I/O, external memory address/data 8, Parallel Slave Port read control input, or ECCP2 PWM output D. |
| 5 | RB0/INT0/FLT0 | bidirectional | PORTB digital I/O with TTL input, External Interrupt 0, or Enhanced PWM Fault input enabled in software. |
| 6 | RB1/INT1 | bidirectional | PORTB digital I/O with TTL input or External Interrupt 1. |
| 7 | RB2/INT2 | bidirectional | PORTB digital I/O with TTL input or External Interrupt 2. |
| 8 | RB3/INT3/ECCP2/P2A | bidirectional | PORTB digital I/O, External Interrupt 3, or alternate ECCP2 capture/compare/PWM pin (P2A) when CCP2MX is cleared in Extended Microcontroller mode. |
| 9 | NC | unconnected | No connect. |
| 10 | RG6 | bidirectional | PORTG digital I/O (Schmitt Trigger). |
| 11 | RG5 | bidirectional | PORTG digital I/O (Schmitt Trigger). |
| 12 | RF0/AN5 | bidirectional | PORTF digital I/O or analog input 5. |
| 13 | MCLR | input | Master Clear (Reset) input, active-low Reset to the device, Schmitt Trigger input. |
| 14 | RG4/CCP5/P1D | bidirectional | PORTG digital I/O, Capture 5 input/Compare 5 output/PWM5 output, or ECCP1 PWM output D. |
| 15 | VSS | power_in | Ground reference for logic and I/O pins. |
| 16 | VDDCORE/VCAP | power_in | Core logic supply (regulator disabled) or external filter capacitor connection (regulator enabled). |
| 17 | VDD | power_in | Positive supply for peripheral digital logic and I/O pins. |
| 18 | RF7/SS1 | bidirectional | PORTF digital I/O or SPI slave select input for MSSP1. |
| 19 | RF6/AN11 | bidirectional | PORTF digital I/O or analog input 11. |
| 20 | RF5/AN10/CVREF | bidirectional | PORTF digital I/O, analog input 10, or comparator reference voltage output. |
| 21 | RF4/AN9 | bidirectional | PORTF digital I/O or analog input 9. |
| 22 | RF3/AN8 | bidirectional | PORTF digital I/O or analog input 8. |
| 23 | RF2/AN7/C1OUT | bidirectional | PORTF digital I/O, analog input 7, or comparator 1 output. |
| 24 | RH7/AN15/P1B | bidirectional | PORTH digital I/O, analog input 15, or ECCP1 PWM output B (alternate assignment when ECCPMX is cleared). |
| 25 | RH6/AN14/P1C | bidirectional | PORTH digital I/O, analog input 14, or ECCP1 PWM output C (alternate assignment when ECCPMX is cleared). |
| 26 | RH5/AN13/P3B | bidirectional | PORTH digital I/O, analog input 13, or ECCP3 PWM output B (alternate assignment when ECCPMX is cleared). |
| 27 | RH4/AN12/P3C | bidirectional | PORTH digital I/O, analog input 12, or ECCP3 PWM output C (alternate assignment when ECCPMX is cleared). |
| 28 | RF1/AN6/C2OUT | bidirectional | PORTF digital I/O, analog input 6, or comparator 2 output. |
| 29 | ENVREG | input | Enable for on-chip voltage regulator; tie to VDD to enable or to ground to disable. |
| 30 | AVDD | power_in | Positive supply for analog modules; must always be connected. |
| 31 | AVSS | power_in | Ground reference for analog modules; must always be connected. |
| 32 | RA3/AN3/VREF+ | bidirectional | PORTA digital I/O, analog input 3, or A/D high reference voltage input (VDD-only input tolerance). |
| 33 | RA2/AN2/VREF- | bidirectional | PORTA digital I/O, analog input 2, or A/D low reference voltage input. |
| 34 | RA1/LEDB/AN1 | bidirectional | PORTA digital I/O, Ethernet LEDB indicator output, or analog input 1. |
| 35 | RA0/LEDA/AN0 | bidirectional | PORTA digital I/O, Ethernet LEDA indicator output, or analog input 0. |
| 36 | VSS | power_in | Ground reference for logic and I/O pins. |
| 37 | VDD | power_in | Positive supply for peripheral digital logic and I/O pins. |
| 38 | RG7 | bidirectional | PORTG digital I/O (Schmitt Trigger). |
| 39 | RJ7/UB | bidirectional | PORTJ digital I/O or external memory upper byte enable control output. |
| 40 | VSS | power_in | Ground reference for logic and I/O pins. |
| 41 | RA5/AN4 | bidirectional | PORTA digital I/O with TTL input or analog input 4. |
| 42 | RA4/T0CKI | bidirectional | PORTA digital I/O or Timer0 external clock input (Schmitt Trigger). |
| 43 | RC1/T1OSI/ECCP2/P2A | bidirectional | PORTC digital I/O, Timer1 oscillator input, or default ECCP2 capture/compare/PWM pin (P2A). |
| 44 | RC0/T1OSO/T13CKI | bidirectional | PORTC digital I/O, Timer1 oscillator output, or Timer1/Timer3 external clock input. |
| 45 | RC6/TX1/CK1 | bidirectional | PORTC digital I/O, EUSART1 asynchronous transmit, or EUSART1 synchronous clock. |
| 46 | RC7/RX1/DT1 | bidirectional | PORTC digital I/O, EUSART1 asynchronous receive, or EUSART1 synchronous data. |
| 47 | RJ4/BA0 | bidirectional | PORTJ digital I/O or external memory byte address 0 control output. |
| 48 | RJ5/CE | bidirectional | PORTJ digital I/O or external memory chip enable control output. |
| 49 | RJ0/ALE | bidirectional | PORTJ digital I/O or external memory address latch enable output. |
| 50 | RJ1/OE | bidirectional | PORTJ digital I/O or external memory output enable output. |
| 51 | RG3/CCP4/P3D | bidirectional | PORTG digital I/O, Capture 4 input/Compare 4 output/PWM4 output, or ECCP3 PWM output D. |
| 52 | RG2/RX2/DT2 | bidirectional | PORTG digital I/O, EUSART2 asynchronous receive, or EUSART2 synchronous data. |
| 53 | RC2/ECCP1/P1A | bidirectional | PORTC digital I/O or Capture 1 input/Compare 1 output/PWM1 output (ECCP1 PWM output A). |
| 54 | RC3/SCK1/SCL1 | bidirectional | PORTC digital I/O or MSSP1 synchronous serial clock for SPI or I2C mode. |
| 55 | RC4/SDI1/SDA1 | bidirectional | PORTC digital I/O, SPI data in, or I2C data I/O for MSSP1. |
| 56 | RC5/SDO1 | bidirectional | PORTC digital I/O or SPI data out for MSSP1. |
| 57 | RB7/KBI3/PGD | bidirectional | PORTB digital I/O, interrupt-on-change, or In-Circuit Debugger/ICSP programming data pin. |
| 58 | RJ6/LB | bidirectional | PORTJ digital I/O or external memory low byte control output. |
| 59 | VDD | power_in | Positive supply for peripheral digital logic and I/O pins. |
| 60 | VSS | power_in | Ground reference for logic and I/O pins. |
| 61 | RJ3/WRH | bidirectional | PORTJ digital I/O or external memory write high control output. |
| 62 | VDD | power_in | Positive supply for peripheral digital logic and I/O pins. |
| 63 | OSC1/CLKI | input | Oscillator crystal input or external clock source input (ST in internal RC mode, CMOS otherwise). |
| 64 | OSC2/CLKO | output | Oscillator crystal output; in internal RC mode outputs CLKO at 1/4 the OSC1 frequency, denoting the instruction cycle rate. |
| 65 | VSS | power_in | Ground reference for logic and I/O pins. |
| 66 | RJ2/WRL | bidirectional | PORTJ digital I/O or external memory write low control output. |
| 67 | RB6/KBI2/PGC | bidirectional | PORTB digital I/O, interrupt-on-change, or In-Circuit Debugger/ICSP programming clock pin. |
| 68 | RB5/KBI1 | bidirectional | PORTB digital I/O or interrupt-on-change pin. |
| 69 | RB4/KBI0 | bidirectional | PORTB digital I/O or interrupt-on-change pin. |
| 70 | RG1/TX2/CK2 | bidirectional | PORTG digital I/O, EUSART2 asynchronous transmit, or EUSART2 synchronous clock. |
| 71 | RG0/ECCP3/P3A | bidirectional | PORTG digital I/O or Capture 3 input/Compare 3 output/PWM3 output (ECCP3 PWM output A). |
| 72 | VSSRX | power_in | Ground reference for Ethernet PHY receive subsystem. |
| 73 | TPIN- | input | Ethernet differential signal input (analog). |
| 74 | TPIN+ | input | Ethernet differential signal input (analog). |
| 75 | VDDRX | power_in | Positive 3.3V supply for Ethernet PHY receive subsystem. |
| 76 | VDDTX | power_in | Positive 3.3V supply for Ethernet PHY transmit subsystem. |
| 77 | TPOUT- | output | Ethernet differential signal output. |
| 78 | TPOUT+ | output | Ethernet differential signal output. |
| 79 | VSSTX | power_in | Ground reference for Ethernet PHY transmit subsystem. |
| 80 | RBIAS | input | Bias current for Ethernet PHY (analog); must be tied to VSS via a resistor. |
| 81 | VDDPLL | power_in | Positive 3.3V supply for Ethernet PHY PLL. |
| 82 | VSSPLL | power_in | Ground reference for Ethernet PHY PLL. |
| 83 | RD7/AD7/PSP7/SS2 | bidirectional | PORTD digital I/O, external memory address/data 7, Parallel Slave Port data, or SPI slave select input for MSSP2. |
| 84 | RD6/AD6/PSP6/SCK2/SCL2 | bidirectional | PORTD digital I/O, external memory address/data 6, Parallel Slave Port data, or MSSP2 SPI/I2C clock. |
| 85 | VSS | power_in | Ground reference for logic and I/O pins. |
| 86 | VDD | power_in | Positive supply for peripheral digital logic and I/O pins. |
| 87 | RD5/AD5/PSP5/SDI2/SDA2 | bidirectional | PORTD digital I/O, external memory address/data 5, Parallel Slave Port data, SPI data in, or I2C data I/O for MSSP2. |
| 88 | RD4/AD4/PSP4/SDO2 | bidirectional | PORTD digital I/O, external memory address/data 4, Parallel Slave Port data, or SPI data out for MSSP2. |
| 89 | RD3/AD3/PSP3 | bidirectional | PORTD digital I/O, external memory address/data 3, or Parallel Slave Port data. |
| 90 | RD2/AD2/PSP2 | bidirectional | PORTD digital I/O, external memory address/data 2, or Parallel Slave Port data. |
| 91 | RD1/AD1/PSP1 | bidirectional | PORTD digital I/O, external memory address/data 1, or Parallel Slave Port data. |
| 92 | RD0/AD0/PSP0 | bidirectional | PORTD digital I/O, external memory address/data 0, or Parallel Slave Port data. |
| 93 | RE7/AD15/ECCP2/P2A | bidirectional | PORTE digital I/O, external memory address/data 15, or alternate ECCP2 capture/compare/PWM pin (P2A) when CCP2MX is cleared in Microcontroller mode. |
| 94 | RE6/AD14/P1B | bidirectional | PORTE digital I/O, external memory address/data 14, or ECCP1 PWM output B. |
| 95 | RE5/AD13/P1C | bidirectional | PORTE digital I/O, external memory address/data 13, or ECCP1 PWM output C. |
| 96 | RE4/AD12/P3B | bidirectional | PORTE digital I/O, external memory address/data 12, or ECCP3 PWM output B. |
| 97 | RE3/AD11/P3C | bidirectional | PORTE digital I/O, external memory address/data 11, or ECCP3 PWM output C. |
| 98 | RE2/AD10/CS/P2B | bidirectional | PORTE digital I/O, external memory address/data 10, Parallel Slave Port chip select input, or ECCP2 PWM output B. |
| 99 | RH0/A16 | bidirectional | PORTH digital I/O or external memory address line 16. |
| 100 | RH1/A17 | bidirectional | PORTH digital I/O or external memory address line 17. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TQFP-100(12x12) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Voltage Range | VDD | 2.35 | 3.6 | V | Operating voltage range | 3 | |
| Operating Voltage Range using Ethernet module | VDD | 3.1 | 3.6 | V | Using Ethernet module | 3 | |
| High-current sink/source on PORTB and PORTC | 25 | mA | PORTB and PORTC, 25 mA sink / 25 mA source | 3 | |||
| Digital-only input pin voltage tolerance | 5.5 | V | Digital-only input pins | 146 | |||
| Required Ethernet clock source frequency | 25 | MHz | Ethernet applications | 51 | |||
| Internal oscillator (INTRC) frequency | 31 | kHz | Nominal output | 51 | |||
| Flash program memory endurance | 100 | cycles | Rated erase/write cycles | 11 | |||
| Flash data retention | 20 | years | Without refresh, conservatively estimated as greater than 20 years | 11 |
CAD (KiCad official)
- Symbol:
PIC18F97J60T-I - Footprint:
Package_QFP:TQFP-100_12x12mm_P0.4mm - 3D model: TQFP-100(12x12) (KiCad packages3D, STEP)
- 3D model files:
pic18f97j60t-i-etched.step/pic18f97j60t-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic18f97j60t-i.step/pic18f97j60t-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (492 pp, sha256
a5190601007a9ae0, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).