Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

PIC18F66J60-I

Microchip Tech · MICROCHIP · TQFP-64(10x10)

PIC18F66J60-I from Microchip Tech, in a TQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RE1/P2C bidirectional Digital I/O (ST) port RE1, multiplexed with ECCP2 PWM Output C.
2 RE0/P2D bidirectional Digital I/O (ST) port RE0, multiplexed with ECCP2 PWM Output D.
3 RB0/INT0/FLT0 bidirectional Digital I/O (TTL) with External Interrupt 0 and Enhanced PWM Fault input (enabled in software); PORTB has software-programmable weak pull-ups.
4 RB1/INT1 bidirectional Digital I/O (TTL) with External Interrupt 1 input.
5 RB2/INT2 bidirectional Digital I/O (TTL) with External Interrupt 2 input.
6 RB3/INT3 bidirectional Digital I/O (TTL) with External Interrupt 3 input.
7 MCLR input Master Clear (Reset) input, active-low Reset to the device (ST).
8 RG4/CCP5/P1D bidirectional Digital I/O (ST) with Capture 5 input/Compare 5 output/PWM5 output and ECCP1 PWM Output D.
9 VSS power_in Ground reference for logic and I/O pins.
10 VDDCORE/VCAP power_in Core logic supply (regulator disabled) or external filter capacitor connection (regulator enabled).
11 RF7/SS1 bidirectional Digital I/O (ST) and SPI slave select input (TTL) for MSSP1.
12 RF6/AN11 bidirectional Digital I/O (ST) or Analog Input 11.
13 RF5/AN10/CVREF bidirectional Digital I/O (ST), Analog Input 10, or comparator reference voltage output.
14 RF4/AN9 bidirectional Digital I/O (ST) or Analog Input 9.
15 RF3/AN8 bidirectional Digital I/O (ST) or Analog Input 8.
16 RF2/AN7/C1OUT bidirectional Digital I/O (ST), Analog Input 7, or Comparator 1 output.
17 RF1/AN6/C2OUT bidirectional Digital I/O (ST), Analog Input 6, or Comparator 2 output.
18 ENVREG input Enable for on-chip voltage regulator (ST); tie to VDD to enable or to ground to disable.
19 AVDD power_in Positive supply for analog modules.
20 AVSS power_in Ground reference for analog modules.
21 RA3/AN3/VREF+ bidirectional Digital I/O (TTL), Analog Input 3, or A/D reference voltage (high) input.
22 RA2/AN2/VREF- bidirectional Digital I/O (TTL), Analog Input 2, or A/D reference voltage (low) input.
23 RA1/LEDB/AN1 bidirectional Digital I/O (TTL), Ethernet LEDB indicator output, or Analog Input 1.
24 RA0/LEDA/AN0 bidirectional Digital I/O (TTL), Ethernet LEDA indicator output, or Analog Input 0.
25 VSS power_in Ground reference for logic and I/O pins.
26 VDD power_in Positive supply for peripheral digital logic and I/O pins.
27 RA5/AN4 bidirectional Digital I/O (TTL) or Analog Input 4.
28 RA4/T0CKI bidirectional Digital I/O (ST) or Timer0 external clock input.
29 RC1/T1OSI/ECCP2/P2A bidirectional Digital I/O, Timer1 oscillator input, Capture 2 input/Compare 2 output/PWM2 output, or ECCP2 PWM Output A.
30 RC0/T1OSO/T13CKI bidirectional Digital I/O (ST), Timer1 oscillator output, or Timer1/Timer3 external clock input.
31 RC6/TX1/CK1 bidirectional Digital I/O, EUSART1 asynchronous transmit, or EUSART1 synchronous clock.
32 RC7/RX1/DT1 bidirectional Digital I/O, EUSART1 asynchronous receive, or EUSART1 synchronous data.
33 RC2/ECCP1/P1A bidirectional Digital I/O, Capture 1 input/Compare 1 output/PWM1 output, or ECCP1 PWM Output A.
34 RC3/SCK1/SCL1 bidirectional Digital I/O (ST) or synchronous serial clock for SPI (SCK1) and I2C (SCL1) modes.
35 RC4/SDI1/SDA1 bidirectional Digital I/O (ST), SPI data in, or I2C data I/O.
36 RC5/SDO1 bidirectional Digital I/O (ST) or SPI data out.
37 RB7/KBI3/PGD bidirectional Digital I/O (TTL), interrupt-on-change pin, or In-Circuit Debugger and ICSP programming data pin.
38 VDD power_in Positive supply for peripheral digital logic and I/O pins.
39 OSC1/CLKI input Oscillator crystal or external clock source input (ST in internal RC mode, CMOS otherwise).
40 OSC2/CLKO output Oscillator crystal output; in Internal RC mode outputs CLKO at 1/4 the OSC1 frequency, denoting the instruction cycle rate.
41 VSS power_in Ground reference for logic and I/O pins.
42 RB6/KBI2/PGC bidirectional Digital I/O (TTL), interrupt-on-change pin, or In-Circuit Debugger and ICSP programming clock pin.
43 RB5/KBI1 bidirectional Digital I/O (TTL) with interrupt-on-change function.
44 RB4/KBI0 bidirectional Digital I/O (TTL) with interrupt-on-change function.
45 VSSRX power_in Ground reference for Ethernet PHY receive subsystem.
46 TPIN- input Ethernet differential signal input (analog).
47 TPIN+ input Ethernet differential signal input (analog).
48 VDDRX power_in Positive 3.3V supply for Ethernet PHY receive subsystem.
49 VDDTX power_in Positive 3.3V supply for Ethernet PHY transmit subsystem.
50 TPOUT- output Ethernet differential signal output.
51 TPOUT+ output Ethernet differential signal output.
52 VSSTX power_in Ground reference for Ethernet PHY transmit subsystem.
53 RBIAS input Bias current pin for Ethernet PHY (analog); must be tied to VSS via a resistor.
54 VDDPLL power_in Positive 3.3V supply for Ethernet PHY PLL.
55 VSSPLL power_in Ground reference for Ethernet PHY PLL.
56 VSS power_in Ground reference for logic and I/O pins.
57 VDD power_in Positive supply for peripheral digital logic and I/O pins.
58 RD2/CCP4/P3D bidirectional Digital I/O (ST), Capture 4 input/Compare 4 output/PWM4 output, or CCP4 PWM Output D.
59 RD1/ECCP3/P3A bidirectional Digital I/O (ST), Capture 3 input/Compare 3 output/PWM3 output, or ECCP3 PWM Output A.
60 RD0/P1B bidirectional Digital I/O (ST) or ECCP1 PWM Output B.
61 RE5/P1C bidirectional Digital I/O (ST) or ECCP1 PWM Output C.
62 RE4/P3B bidirectional Digital I/O (ST) or ECCP3 PWM Output B.
63 RE3/P3C bidirectional Digital I/O (ST) or ECCP3 PWM Output C.
64 RE2/P2B bidirectional Digital I/O (ST) or ECCP2 PWM Output B.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package TQFP-64(10x10)
Category Embedded Processors & Controllers
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
PLL Oscillator Frequency Range (HSPLL mode) FOSC 8 25 MHz HSPLL mode; VDD = 2.6V to 3.6V 446
PLL Oscillator Frequency Range (ECPLL mode) FOSC 8 37.5 MHz ECPLL mode; VDD = 2.6V to 3.6V 446
On-Chip VCO System Frequency FSYS 20 62.5 MHz 446
PLL Start-up Time (Lock Time) trc 2 ms 446
CLKO Stability (Jitter) CLK -2 2 % 446
INTRC Accuracy @ Freq = 31 kHz 21.7 40.3 kHz INTRC frequency changes as VDDCORE changes 446

CAD (KiCad official)

  • Symbol: PIC18F66J60-I
  • Footprint: Package_QFP:TQFP-64_10x10mm_P0.5mm
  • 3D model: TQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: pic18f66j60-i-etched.step / pic18f66j60-i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pic18f66j60-i.step / pic18f66j60-i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (492 pp, sha256 a5190601007a9ae0, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF