Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

PIC18F25J10-I

Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SOIC-28-300mil

PIC18F25J10-I from Microchip Tech, in a SOIC-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 MCLR input Master Clear input is an active-low device Reset and also serves as the programming voltage input.
2 RA0/AN0 bidirectional Digital I/O with TTL input levels, also Analog Input 0 and Comparator C1- input.
3 RA1/AN1 bidirectional Digital I/O with TTL input levels, also Analog Input 1 and Comparator C2- input.
4 RA2/AN2/VREF-/CVREF bidirectional Digital I/O with TTL input levels, also Analog Input 2, A/D low reference voltage input, and comparator voltage reference output CVREF.
5 RA3/AN3/VREF+ bidirectional Digital I/O with TTL input levels, also Analog Input 3 and A/D high reference voltage input VREF+.
6 VDDCORE/VCAP power_in Core voltage pin for the on-chip regulator; with the regulator enabled it requires a low-ESR capacitor (10 µF typical) to VSS and must not be connected to VDD.
7 RA5/AN4/SS1/C2OUT bidirectional Digital I/O with TTL input levels, also Analog Input 4, SPI slave select input for MSSP1, and Comparator 2 output.
8 VSS power_in Ground reference for logic and I/O pins.
9 OSC1/CLKI input Oscillator crystal input or external clock source input with CMOS levels.
10 OSC2/CLKO output Oscillator crystal output connecting to the crystal or resonator, or CLKO output at 1/4 the OSC1 frequency in EC mode.
11 RC0/T1OSO/T1CKI bidirectional Digital I/O with Schmitt Trigger input, also Timer1 oscillator output and Timer1 external clock input.
12 RC1/T1OSI/CCP2 bidirectional Digital I/O with Schmitt Trigger input, also Timer1 oscillator input and CCP2 capture input/compare output/PWM2 output (default assignment when CCP2MX is set).
13 RC2/CCP1 bidirectional Digital I/O with Schmitt Trigger input, also Capture 1 input, Compare 1 output and PWM1 output.
14 RC3/SCK1/SCL1 bidirectional Digital I/O with Schmitt Trigger input, also MSSP1 SPI serial clock input/output and I2C clock input/output.
15 RC4/SDI1/SDA1 bidirectional Digital I/O with Schmitt Trigger input, also MSSP1 SPI data input and I2C data I/O.
16 RC5/SDO1 bidirectional Digital I/O with Schmitt Trigger input, also MSSP1 SPI data output.
17 RC6/TX/CK bidirectional Digital I/O with Schmitt Trigger input, also EUSART asynchronous transmit output and synchronous clock.
18 RC7/RX/DT bidirectional Digital I/O with Schmitt Trigger input, also EUSART asynchronous receive input and synchronous data I/O.
19 VSS power_in Ground reference for logic and I/O pins.
20 VDD power_in Positive supply for logic and I/O pins.
21 RB0/INT0/FLT0/AN12 bidirectional Digital I/O with weak pull-up option, also External Interrupt 0, PWM Fault input for CCP1 and Analog Input 12.
22 RB1/INT1/AN10 bidirectional Digital I/O with weak pull-up option, also External Interrupt 1 and Analog Input 10.
23 RB2/INT2/AN8 bidirectional Digital I/O with weak pull-up option, also External Interrupt 2 and Analog Input 8.
24 RB3/AN9/CCP2 bidirectional Digital I/O with weak pull-up option, also Analog Input 9 and CCP2 capture/compare/PWM output (alternate assignment when CCP2MX is cleared).
25 RB4/KBI0/AN11 bidirectional Digital I/O with weak pull-up option, also interrupt-on-change pin KBI0 and Analog Input 11.
26 RB5/KBI1/T0CKI/C1OUT bidirectional Digital I/O with weak pull-up option, also interrupt-on-change pin KBI1, Timer0 external clock input T0CKI and Comparator 1 output.
27 RB6/KBI2/PGC bidirectional Digital I/O with weak pull-up option, also interrupt-on-change pin KBI2 and the ICSP/ICD programming clock PGC.
28 RB7/KBI3/PGD bidirectional Digital I/O with weak pull-up option, also interrupt-on-change pin KBI3 and the ICSP/ICD programming data PGD.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-28-300mil
Category Single Chip Microcomputer/Microcontroller
Pins 28

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VDD (F device, regulator enabled) VDD 2.7 3.6 V PIC18F25J10 F device, on-chip voltage regulator enabled 10
Input voltage tolerance, digital-only pins 5.5 V Digital-only input pins PORTB<7:6> and PORTC<7:2>; pins with analog functions tolerate only up to VDD 99

CAD (KiCad official)

  • Symbol: PIC18F25J10-I
  • Footprint: Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm
  • 3D model: SOIC-28-300mil (KiCad packages3D, STEP)
  • 3D model files: pic18f25j10-i-etched.step / pic18f25j10-i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pic18f25j10-i.step / pic18f25j10-i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (368 pp, sha256 200de743a909cb1c, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF