Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

PIC16LF873A-I/SS

Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SSOP-28-208mil

PIC16LF873A-I from Microchip Tech, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 MCLR/VPP input Master Clear (Reset) input is an active low Reset to the device, and this pin also serves as the programming voltage input VPP.
2 RA0/AN0 bidirectional Digital I/O (TTL input buffer) that also serves as analog input 0.
3 RA1/AN1 bidirectional Digital I/O (TTL input buffer) that also serves as analog input 1.
4 RA2/AN2/VREF-/CVREF bidirectional Digital I/O (TTL input buffer) that also serves as analog input 2, the A/D reference voltage (low) input, and the comparator VREF output.
5 RA3/AN3/VREF+ bidirectional Digital I/O (TTL input buffer) that also serves as analog input 3 and the A/D reference voltage (high) input.
6 RA4/T0CKI/C1OUT bidirectional Digital I/O (Schmitt Trigger input, open-drain when configured as output) that also serves as the Timer0 external clock input and the Comparator 1 output.
7 RA5/AN4/SS/C2OUT bidirectional Digital I/O (TTL input buffer) that also serves as analog input 4, the SPI slave select input, and the Comparator 2 output.
8 VSS power_in Ground reference for logic and I/O pins.
9 OSC1/CLKI input Oscillator crystal input or external clock source input (Schmitt Trigger when in RC mode, otherwise CMOS).
10 OSC2/CLKO output Oscillator crystal output connecting to the crystal or resonator; in RC mode it outputs CLKO at 1/4 the OSC1 frequency.
11 RC0/T1OSO/T1CKI bidirectional Digital I/O (Schmitt Trigger input) that also serves as the Timer1 oscillator output and the Timer1 external clock input.
12 RC1/T1OSI/CCP2 bidirectional Digital I/O (Schmitt Trigger input) that also serves as the Timer1 oscillator input and the Capture2 input, Compare2 output or PWM2 output.
13 RC2/CCP1 bidirectional Digital I/O (Schmitt Trigger input) that also serves as the Capture1 input, Compare1 output or PWM1 output.
14 RC3/SCK/SCL bidirectional Digital I/O (Schmitt Trigger input) that also serves as the synchronous serial clock input/output for SPI mode and for I2C mode.
15 RC4/SDI/SDA bidirectional Digital I/O (Schmitt Trigger input) that also serves as the SPI data input and the I2C data I/O.
16 RC5/SDO bidirectional Digital I/O (Schmitt Trigger input) that also serves as the SPI data output.
17 RC6/TX/CK bidirectional Digital I/O (Schmitt Trigger input) that also serves as the USART asynchronous transmit output and the USART synchronous clock.
18 RC7/RX/DT bidirectional Digital I/O (Schmitt Trigger input) that also serves as the USART asynchronous receive input and the USART synchronous data.
19 VSS power_in Ground reference for logic and I/O pins.
20 VDD power_in Positive supply for logic and I/O pins.
21 RB0/INT bidirectional Digital I/O (TTL/Schmitt Trigger input) that also serves as the external interrupt input.
22 RB1 bidirectional Digital I/O with TTL input buffer; PORTB pins can be software-programmed for internal weak pull-ups.
23 RB2 bidirectional Digital I/O with TTL input buffer; PORTB pins can be software-programmed for internal weak pull-ups.
24 RB3/PGM bidirectional Digital I/O (TTL input buffer) that also serves as the low-voltage (single-supply) ICSP programming enable pin.
25 RB4 bidirectional Digital I/O with TTL input buffer; PORTB pins can be software-programmed for internal weak pull-ups.
26 RB5 bidirectional Digital I/O with TTL input buffer; PORTB pins can be software-programmed for internal weak pull-ups.
27 RB6/PGC bidirectional Digital I/O (TTL/Schmitt Trigger input) that also serves as the in-circuit debugger and ICSP programming clock.
28 RB7/PGD bidirectional Digital I/O (TTL/Schmitt Trigger input) that also serves as the in-circuit debugger and ICSP programming data.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SSOP-28-208mil
Category Single Chip Microcomputer/Microcontroller
Pins 28

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient temperature under bias -55 125 °C 173
Storage temperature -65 150 °C 173
Voltage on VDD with respect to VSS VDD -0.3 7.5 V 173
Voltage on MCLR with respect to VSS MCLR 0 14 V Note 2 173
Voltage on RA4 with respect to VSS RA4 0 8.5 V 173
Voltage on any pin with respect to VSS -0.3 V Except VDD, MCLR and RA4; upper limit is VDD + 0.3V 173
Total power dissipation 1 W Note 1 173
Input clamp current IIK 20 mA VI < 0 or VI > VDD 173
Output clamp current IOK 20 mA VO < 0 or VO > VDD 173
Supply voltage (PIC16LF87XA) VDD 2 5.5 V All configurations (DC to 10 MHz) 175
Operating temperature -40 85 °C Industrial 175
VDD rise rate to ensure internal Power-on Reset signal SVDD 0.05 V/ms See Section 14.5 Power-on Reset (POR) 175
Brown-out Reset voltage VBOR 3.65 4 4.35 V BODEN bit in configuration word enabled 175
Supply current (LF, XT/RC) IDD 0.6 2 mA XT, RC osc configurations, FOSC = 4 MHz, VDD = 3.0V 176
Supply current (LF, LP) IDD 20 35 µA LP osc configuration, FOSC = 32 kHz, VDD = 3.0V, WDT disabled 176
Brown-out Reset current IBOR 85 200 µA BOR enabled, VDD = 5.0V 176
Power-down current (LF, WDT enabled) IPD 7.5 30 µA VDD = 3.0V, WDT enabled, -40C to +85C 177
Power-down current (LF, WDT disabled, 0C to +70C) IPD 0.9 5 µA VDD = 3.0V, WDT disabled, 0C to +70C 177
Power-down current (LF, WDT disabled, -40C to +85C) IPD 0.9 5 µA VDD = 3.0V, WDT disabled, -40C to +85C 177
Brown-out Reset current IBOR 85 200 µA BOR enabled, VDD = 5.0V 177
Input low voltage, TTL buffer VIL 0.8 V 4.5V <= VDD <= 5.5V 178
Input low voltage, Schmitt Trigger buffer VIL 0.2 xVDD Schmitt Trigger buffer 178
Input low voltage, MCLR and OSC1 (RC mode) VIL 0.2 xVDD MCLR, OSC1 in RC mode 178
Input low voltage, OSC1 (XT and LP modes) VIL 0.3 V OSC1 in XT and LP modes; Note 1 178
Input low voltage, RC3 and RC4 with SMBus VIL -0.5 0.6 V VDD = 4.5 to 5.5V 178
Input high voltage, TTL buffer VIH 2 V 4.5V <= VDD <= 5.5V 178
Input high voltage, Schmitt Trigger buffer VIH 0.8 xVDD For entire VDD range 178
Input high voltage, MCLR VIH 0.8 xVDD 178
Input high voltage, OSC1 (XT and LP modes) VIH 1.6 V OSC1 in XT and LP modes; Note 1 178
Input high voltage, OSC1 (RC mode) VIH 0.9 xVDD OSC1 in RC mode 178
Input high voltage, RC3 and RC4 with SMBus VIH 1.4 5.5 V VDD = 4.5 to 5.5V 178
PORTB weak pull-up current IPURB 50 250 400 µA VDD = 5V, VPIN = VSS, -40°C TO +85°C 178
Input leakage current, I/O ports IIL 1 µA VSS <= VPIN <= VDD, pin at high-impedance 178
Input leakage current, MCLR and RA4/T0CKI IIL 5 µA VSS <= VPIN <= VDD 178
Output low voltage, I/O ports VOL 0.6 V IOL = 8.5 mA, VDD = 4.5V, -40C to +85C 179
Output low voltage, OSC2/CLKO (RC osc config) VOL 0.6 V IOL = 1.6 mA, VDD = 4.5V, -40C to +85C 179
Open-drain high voltage VOD 8.5 V RA4 pin 179
OSC2 pin capacitive loading COSC2 15 pF In XT, HS and LP modes when external clock is used to drive OSC1 179
Data EEPROM erase/write cycle time TDEW 4 8 ms 179
VDD for erase/write (data EEPROM) VDD 5.5 V Using EECON to read/write, VMIN = min. operating voltage 179
VDD for read (program Flash) VPR 5.5 V VMIN = min. operating voltage 179
Program Flash erase/write cycle time TPEW 4 8 ms 179
Comparator input offset voltage VIOFF -10 5 10 mV 180
Comparator response time (PIC16LF87XA) TRESP 150 600 ns One input at (VDD - 1.5)/2, other transitions VSS to VDD 180
A/D integral linearity error EIL -1 1 LSb VREF = VDD = 5.12V, VSS <= VAIN <= VREF 194
A/D offset error EOFF -2 2 LSb VREF = VDD = 5.12V, VSS <= VAIN <= VREF 194
VREF input current during VAIN acquisition IREF 5 µA During VAIN acquisition 194
VREF input current during A/D conversion cycle IREF 150 µA During A/D conversion cycle 194
A/D clock period (PIC16LF87XA, TOSC based) TAD 3 µs TOSC based, VREF >= 2.0V 195
A/D clock period (PIC16LF87XA, RC mode) TAD 3 6 9 µs A/D RC mode 195

CAD (KiCad official)

  • Symbol: PIC16LF873A-I
  • Footprint: Package_SO:SSOP-28_5.3x10.2mm_P0.65mm
  • 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
  • 3D model files: pic16lf873a-i-etched.step / pic16lf873a-i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pic16lf873a-i.step / pic16lf873a-i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (234 pp, sha256 94f1cb4c43edd96e, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

Other parts in this family

This page is PIC16LF873A-I/SS. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:

  • PIC16LF873A-I/SO
  • PIC16LF873A-I/SP