main
Ray
Publish 0.1.2
2ac2d4d
PIC16F872T-I
Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · SOIC-28-300mil
PIC16F872T-I from Microchip Tech, in a SOIC-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MCLR/VPP | input | Active-low master clear (Reset) input to the device, or programming voltage input; ST input buffer. |
| 2 | RA0/AN0 | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; analog input 0. |
| 3 | RA1/AN1 | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; analog input 1. |
| 4 | RA2/AN2/VREF- | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; analog input 2 and negative analog reference voltage. |
| 5 | RA3/AN3/VREF+ | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; analog input 3 and positive analog reference voltage. |
| 6 | RA4/T0CKI | bidirectional | Digital I/O with Schmitt Trigger input buffer, open drain when configured as output; Timer0 clock input. |
| 7 | RA5/SS/AN4 | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; slave select for the synchronous serial port and analog input 4. |
| 8 | VSS | power_in | Ground reference for logic and I/O pins. |
| 9 | OSC1/CLKI | input | Oscillator crystal or external clock input; Schmitt Trigger buffer when configured in RC mode, otherwise CMOS. |
| 10 | OSC2/CLKO | output | Oscillator crystal output to crystal or resonator; in RC mode outputs CLKO at 1/4 the OSC1 frequency denoting the instruction cycle rate. |
| 11 | RC0/T1OSO/T1CKI | bidirectional | Digital I/O with Schmitt Trigger input buffer; Timer1 oscillator output and Timer1 clock input. |
| 12 | RC1/T1OSI/CCP2 | bidirectional | Digital I/O with Schmitt Trigger input buffer; Timer1 oscillator input. |
| 13 | RC2/CCP1 | bidirectional | Digital I/O with Schmitt Trigger input buffer; Capture1 input, Compare1 output or PWM1 output. |
| 14 | RC3/SCK/SCL | bidirectional | Digital I/O with Schmitt Trigger input buffer; synchronous serial clock input/output for SPI mode and for I2C mode. |
| 15 | RC4/SDI/SDA | bidirectional | Digital I/O with Schmitt Trigger input buffer; SPI data in pin (SPI mode) and SPI data I/O pin (I2C mode). |
| 16 | RC5/SDO | bidirectional | Digital I/O with Schmitt Trigger input buffer; SPI data out pin (SPI mode). |
| 17 | RC6 | bidirectional | Digital I/O with Schmitt Trigger input buffer. |
| 18 | RC7 | bidirectional | Digital I/O with Schmitt Trigger input buffer. |
| 19 | VSS | power_in | Ground reference for logic and I/O pins. |
| 20 | VDD | power_in | Positive supply for logic and I/O pins. |
| 21 | RB0/INT | bidirectional | Digital I/O with TTL input buffer, Schmitt Trigger when configured as the external interrupt pin (INT). |
| 22 | RB1 | bidirectional | Digital I/O with TTL input buffer. |
| 23 | RB2 | bidirectional | Digital I/O with TTL input buffer. |
| 24 | RB3/PGM | bidirectional | Digital I/O with TTL input buffer; low voltage ICSP programming enable pin. |
| 25 | RB4 | bidirectional | Digital I/O with TTL input buffer; PORTB internal weak pull-up is software programmable on all inputs. |
| 26 | RB5 | bidirectional | Digital I/O with TTL input buffer; PORTB internal weak pull-up is software programmable on all inputs. |
| 27 | RB6/PGC | bidirectional | Digital I/O with TTL/Schmitt Trigger input buffer (Schmitt Trigger in serial programming mode); in-circuit debugger and ICSP programming clock. |
| 28 | RB7/PGD | bidirectional | Digital I/O with TTL/Schmitt Trigger input buffer (Schmitt Trigger in serial programming mode); in-circuit debugger and ICSP programming data. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-28-300mil |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (LP, XT, RC osc configuration) | VDD | 4 | 5.5 | V | LP, XT, RC osc configuration | 121 | |
| Supply voltage (BOR enabled, FMAX = 14 MHz) | VDD | 5.5 | V | BOR enabled, FMAX = 14 MHz | 121 | ||
| VDD rise rate to ensure internal Power-on Reset signal | SVDD | 0.05 | V/ms | 121 | |||
| Brown-out Reset voltage | VBOR | 3.7 | 4 | 4.35 | V | BODEN bit in configuration word enabled | 121 |
| Supply current (RC osc configurations) | IDD | 1.6 | 4 | mA | FOSC = 4 MHz, VDD = 5.5V | 121 | |
| Supply current (HS osc configuration) | IDD | 7 | 15 | mA | FOSC = 20 MHz, VDD = 5.5V | 121 | |
| Brown-out Reset current | ΔIBOR | 85 | 200 | μA | BOR enabled, VDD = 5.0V | 122 | |
| Power-down current (WDT enabled) | IPD | 10.5 | 42 | μA | VDD = 4.0V, WDT enabled, -40°C to +85°C | 122 | |
| Power-down current (WDT disabled) | IPD | 1.5 | 16 | μA | VDD = 4.0V, WDT disabled, -40°C to +85°C | 122 | |
| Power-down current (WDT disabled, -40 to +85°C row D021A) | IPD | 1.5 | 19 | μA | VDD = 4.0V, WDT disabled, -40°C to +85°C | 122 | |
| Brown-out Reset current (D023) | ΔIBOR | 85 | 200 | μA | BOR enabled, VDD = 5.0V | 122 | |
| Input high voltage, TTL buffer | VIH | 2 | V | 4.5V ≤ VDD ≤ 5.5V, I/O ports with TTL buffer | 123 | ||
| Input leakage current, I/O ports | IIL | -1 | 1 | μA | Vss ≤ VPIN ≤ VDD, pin at hi-impedance | 123 | |
| Input leakage current, MCLR and RA4/T0CKI | IIL | -5 | 5 | μA | Vss ≤ VPIN ≤ VDD | 123 | |
| Input leakage current, OSC1 | IIL | -5 | 5 | μA | Vss ≤ VPIN ≤ VDD, XT, HS and LP osc configuration | 123 | |
| PORTB weak pull-up current | IPURB | 50 | 250 | 400 | μA | VDD = 5V, VPIN = VSS, -40°C to +85°C | 123 |
| Output low voltage, I/O ports | VOL | 0.6 | V | IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C | 124 | ||
| Output low voltage, OSC2/CLKOUT (RC osc config) | VOL | 0.6 | V | IOL = 1.6 mA, VDD = 4.5V, -40°C to +85°C | 124 | ||
| Open drain high voltage, RA4 pin | VOD | 8.5 | V | RA4 pin | 124 | ||
| OSC2 pin capacitive loading | COSC2 | 15 | pF | In XT, HS and LP modes when external clock is used to drive OSC1 | 124 | ||
| All I/O pins and OSC2 (RC mode) capacitive loading | CIO | 50 | pF | All I/O pins and OSC2 (RC mode) | 124 | ||
| SCL, SDA (I2C mode) bus capacitive loading | CB | 400 | pF | SCL, SDA (I2C mode) | 124 | ||
| VDD for read/write (data EEPROM) | VDRW | 5.5 | V | Using EECON to read/write, VMIN = min. operating voltage | 124 | ||
| Data EEPROM erase/write cycle time | TDEW | 4 | 8 | ms | 124 | ||
| Program FLASH endurance | EP | 1000 | E/W | 25°C at 5V | 124 | ||
| VDD for read (program FLASH) | VPR | 5.5 | V | VMIN = min. operating voltage | 124 | ||
| VDD for erase/write (program FLASH) | VDD | 5.5 | V | Using EECON to read/write, VMIN = min. operating voltage | 124 | ||
| Program FLASH erase/write cycle time | TPEW | 4 | 8 | ms | 124 | ||
| A/D integral linearity error | EIL | -1 | 1 | LSb | VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF (printed < ± 1 LSb) | 138 | |
| A/D differential linearity error | EDL | -1 | 1 | LSb | VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF (printed < ± 1 LSb) | 138 | |
| A/D offset error | EOFF | -2 | 2 | LSb | VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF (printed < ± 2 LSb) | 138 | |
| A/D gain error | EGN | -1 | 1 | LSb | VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF (printed < ± 1 LSb) | 138 | |
| A/D reference voltage (VREF+ - VREF-) | VREF | 2 | V | Absolute minimum electrical spec. to ensure 10-bit accuracy | 138 | ||
| Recommended impedance of analog voltage source | ZAIN | 10 | kΩ | 138 | |||
| External CLKIN frequency (XT and RC osc mode) | FOSC | 4 | MHz | XT and RC osc mode (min printed as DC) | 129 | ||
| External CLKIN frequency (HS osc mode -04) | FOSC | 4 | MHz | HS osc mode (-04) | 129 | ||
| External CLKIN frequency (HS osc mode -20) | FOSC | 20 | MHz | HS osc mode (-20) | 129 | ||
| External CLKIN frequency (LP osc mode) | FOSC | 200 | kHz | LP osc mode (min printed as DC) | 129 | ||
| Instruction cycle time | TCY | 200 | ns | TCY = 4/FOSC | 129 | ||
| Ambient temperature under bias | -55 | 125 | °C | 119 | |||
| Storage temperature | -65 | 150 | °C | 119 | |||
| Voltage on any pin with respect to VSS (except VDD, MCLR and RA4) | -0.3 | V | Upper limit printed as VDD + 0.3V | 119 | |||
| Voltage on VDD with respect to VSS | -0.3 | 7.5 | V | 119 | |||
| Voltage on MCLR with respect to VSS | 0 | 14 | V | Note 2 | 119 | ||
| Voltage on RA4 with respect to VSS | 0 | 8.5 | V | 119 | |||
| Total power dissipation | 1 | W | Note 1 | 119 | |||
| Input clamp current, IIK | IIK | -20 | 20 | mA | VI < 0 or VI > VDD | 119 | |
| Output clamp current, IOK | IOK | -20 | 20 | mA | VO < 0 or VO > VDD | 119 |
CAD (KiCad official)
- Symbol:
PIC16F872T-I - Footprint:
Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm - 3D model: SOIC-28-300mil (KiCad packages3D, STEP)
- 3D model files:
pic16f872t-i-so-etched.step/pic16f872t-i-so-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pic16f872t-i-so.step/pic16f872t-i-so.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (168 pp, sha256
65bfeec06751e6d6, retrieved 2026-11-17) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PIC16F872T-I
**Microchip Tech** · Microcontroller Units (MCUs/MPUs/SOCs) · SOIC-28-300mil
PIC16F872T-I from Microchip Tech, in a SOIC-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MCLR/VPP | input | Active-low master clear (Reset) input to the device, or programming voltage input; ST input buffer. |
| 2 | RA0/AN0 | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; analog input 0. |
| 3 | RA1/AN1 | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; analog input 1. |
| 4 | RA2/AN2/VREF- | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; analog input 2 and negative analog reference voltage. |
| 5 | RA3/AN3/VREF+ | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; analog input 3 and positive analog reference voltage. |
| 6 | RA4/T0CKI | bidirectional | Digital I/O with Schmitt Trigger input buffer, open drain when configured as output; Timer0 clock input. |
| 7 | RA5/SS/AN4 | bidirectional | PORTA bidirectional digital I/O with TTL input buffer; slave select for the synchronous serial port and analog input 4. |
| 8 | VSS | power_in | Ground reference for logic and I/O pins. |
| 9 | OSC1/CLKI | input | Oscillator crystal or external clock input; Schmitt Trigger buffer when configured in RC mode, otherwise CMOS. |
| 10 | OSC2/CLKO | output | Oscillator crystal output to crystal or resonator; in RC mode outputs CLKO at 1/4 the OSC1 frequency denoting the instruction cycle rate. |
| 11 | RC0/T1OSO/T1CKI | bidirectional | Digital I/O with Schmitt Trigger input buffer; Timer1 oscillator output and Timer1 clock input. |
| 12 | RC1/T1OSI/CCP2 | bidirectional | Digital I/O with Schmitt Trigger input buffer; Timer1 oscillator input. |
| 13 | RC2/CCP1 | bidirectional | Digital I/O with Schmitt Trigger input buffer; Capture1 input, Compare1 output or PWM1 output. |
| 14 | RC3/SCK/SCL | bidirectional | Digital I/O with Schmitt Trigger input buffer; synchronous serial clock input/output for SPI mode and for I2C mode. |
| 15 | RC4/SDI/SDA | bidirectional | Digital I/O with Schmitt Trigger input buffer; SPI data in pin (SPI mode) and SPI data I/O pin (I2C mode). |
| 16 | RC5/SDO | bidirectional | Digital I/O with Schmitt Trigger input buffer; SPI data out pin (SPI mode). |
| 17 | RC6 | bidirectional | Digital I/O with Schmitt Trigger input buffer. |
| 18 | RC7 | bidirectional | Digital I/O with Schmitt Trigger input buffer. |
| 19 | VSS | power_in | Ground reference for logic and I/O pins. |
| 20 | VDD | power_in | Positive supply for logic and I/O pins. |
| 21 | RB0/INT | bidirectional | Digital I/O with TTL input buffer, Schmitt Trigger when configured as the external interrupt pin (INT). |
| 22 | RB1 | bidirectional | Digital I/O with TTL input buffer. |
| 23 | RB2 | bidirectional | Digital I/O with TTL input buffer. |
| 24 | RB3/PGM | bidirectional | Digital I/O with TTL input buffer; low voltage ICSP programming enable pin. |
| 25 | RB4 | bidirectional | Digital I/O with TTL input buffer; PORTB internal weak pull-up is software programmable on all inputs. |
| 26 | RB5 | bidirectional | Digital I/O with TTL input buffer; PORTB internal weak pull-up is software programmable on all inputs. |
| 27 | RB6/PGC | bidirectional | Digital I/O with TTL/Schmitt Trigger input buffer (Schmitt Trigger in serial programming mode); in-circuit debugger and ICSP programming clock. |
| 28 | RB7/PGD | bidirectional | Digital I/O with TTL/Schmitt Trigger input buffer (Schmitt Trigger in serial programming mode); in-circuit debugger and ICSP programming data. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-28-300mil |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 28 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (LP, XT, RC osc configuration) | VDD | 4 | | 5.5 | V | LP, XT, RC osc configuration | 121 |
| Supply voltage (BOR enabled, FMAX = 14 MHz) | VDD | | | 5.5 | V | BOR enabled, FMAX = 14 MHz | 121 |
| VDD rise rate to ensure internal Power-on Reset signal | SVDD | 0.05 | | | V/ms | | 121 |
| Brown-out Reset voltage | VBOR | 3.7 | 4 | 4.35 | V | BODEN bit in configuration word enabled | 121 |
| Supply current (RC osc configurations) | IDD | | 1.6 | 4 | mA | FOSC = 4 MHz, VDD = 5.5V | 121 |
| Supply current (HS osc configuration) | IDD | | 7 | 15 | mA | FOSC = 20 MHz, VDD = 5.5V | 121 |
| Brown-out Reset current | ΔIBOR | | 85 | 200 | μA | BOR enabled, VDD = 5.0V | 122 |
| Power-down current (WDT enabled) | IPD | | 10.5 | 42 | μA | VDD = 4.0V, WDT enabled, -40°C to +85°C | 122 |
| Power-down current (WDT disabled) | IPD | | 1.5 | 16 | μA | VDD = 4.0V, WDT disabled, -40°C to +85°C | 122 |
| Power-down current (WDT disabled, -40 to +85°C row D021A) | IPD | | 1.5 | 19 | μA | VDD = 4.0V, WDT disabled, -40°C to +85°C | 122 |
| Brown-out Reset current (D023) | ΔIBOR | | 85 | 200 | μA | BOR enabled, VDD = 5.0V | 122 |
| Input high voltage, TTL buffer | VIH | 2 | | | V | 4.5V ≤ VDD ≤ 5.5V, I/O ports with TTL buffer | 123 |
| Input leakage current, I/O ports | IIL | -1 | | 1 | μA | Vss ≤ VPIN ≤ VDD, pin at hi-impedance | 123 |
| Input leakage current, MCLR and RA4/T0CKI | IIL | -5 | | 5 | μA | Vss ≤ VPIN ≤ VDD | 123 |
| Input leakage current, OSC1 | IIL | -5 | | 5 | μA | Vss ≤ VPIN ≤ VDD, XT, HS and LP osc configuration | 123 |
| PORTB weak pull-up current | IPURB | 50 | 250 | 400 | μA | VDD = 5V, VPIN = VSS, -40°C to +85°C | 123 |
| Output low voltage, I/O ports | VOL | | | 0.6 | V | IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C | 124 |
| Output low voltage, OSC2/CLKOUT (RC osc config) | VOL | | | 0.6 | V | IOL = 1.6 mA, VDD = 4.5V, -40°C to +85°C | 124 |
| Open drain high voltage, RA4 pin | VOD | | | 8.5 | V | RA4 pin | 124 |
| OSC2 pin capacitive loading | COSC2 | | | 15 | pF | In XT, HS and LP modes when external clock is used to drive OSC1 | 124 |
| All I/O pins and OSC2 (RC mode) capacitive loading | CIO | | | 50 | pF | All I/O pins and OSC2 (RC mode) | 124 |
| SCL, SDA (I2C mode) bus capacitive loading | CB | | | 400 | pF | SCL, SDA (I2C mode) | 124 |
| VDD for read/write (data EEPROM) | VDRW | | | 5.5 | V | Using EECON to read/write, VMIN = min. operating voltage | 124 |
| Data EEPROM erase/write cycle time | TDEW | | 4 | 8 | ms | | 124 |
| Program FLASH endurance | EP | 1000 | | | E/W | 25°C at 5V | 124 |
| VDD for read (program FLASH) | VPR | | | 5.5 | V | VMIN = min. operating voltage | 124 |
| VDD for erase/write (program FLASH) | VDD | | | 5.5 | V | Using EECON to read/write, VMIN = min. operating voltage | 124 |
| Program FLASH erase/write cycle time | TPEW | | 4 | 8 | ms | | 124 |
| A/D integral linearity error | EIL | -1 | | 1 | LSb | VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF (printed < ± 1 LSb) | 138 |
| A/D differential linearity error | EDL | -1 | | 1 | LSb | VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF (printed < ± 1 LSb) | 138 |
| A/D offset error | EOFF | -2 | | 2 | LSb | VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF (printed < ± 2 LSb) | 138 |
| A/D gain error | EGN | -1 | | 1 | LSb | VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF (printed < ± 1 LSb) | 138 |
| A/D reference voltage (VREF+ - VREF-) | VREF | 2 | | | V | Absolute minimum electrical spec. to ensure 10-bit accuracy | 138 |
| Recommended impedance of analog voltage source | ZAIN | | | 10 | kΩ | | 138 |
| External CLKIN frequency (XT and RC osc mode) | FOSC | | | 4 | MHz | XT and RC osc mode (min printed as DC) | 129 |
| External CLKIN frequency (HS osc mode -04) | FOSC | | | 4 | MHz | HS osc mode (-04) | 129 |
| External CLKIN frequency (HS osc mode -20) | FOSC | | | 20 | MHz | HS osc mode (-20) | 129 |
| External CLKIN frequency (LP osc mode) | FOSC | | | 200 | kHz | LP osc mode (min printed as DC) | 129 |
| Instruction cycle time | TCY | 200 | | | ns | TCY = 4/FOSC | 129 |
| Ambient temperature under bias | | -55 | | 125 | °C | | 119 |
| Storage temperature | | -65 | | 150 | °C | | 119 |
| Voltage on any pin with respect to VSS (except VDD, MCLR and RA4) | | -0.3 | | | V | Upper limit printed as VDD + 0.3V | 119 |
| Voltage on VDD with respect to VSS | | -0.3 | | 7.5 | V | | 119 |
| Voltage on MCLR with respect to VSS | | 0 | | 14 | V | Note 2 | 119 |
| Voltage on RA4 with respect to VSS | | 0 | | 8.5 | V | | 119 |
| Total power dissipation | | | | 1 | W | Note 1 | 119 |
| Input clamp current, IIK | IIK | -20 | | 20 | mA | VI < 0 or VI > VDD | 119 |
| Output clamp current, IOK | IOK | -20 | | 20 | mA | VO < 0 or VO > VDD | 119 |
## CAD (KiCad official)
- Symbol: `PIC16F872T-I`
- Footprint: `Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm`
- 3D model: SOIC-28-300mil (KiCad packages3D, STEP)
- 3D model files: `pic16f872t-i-so-etched.step` / `pic16f872t-i-so-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pic16f872t-i-so.step` / `pic16f872t-i-so.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/30221c.pdf) (168 pp, sha256 `65bfeec06751e6d6`, retrieved 2026-11-17)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pic16f872t-i-so-datasheet.pdf)