Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

PIC12CE674-04I

Microchip Tech · Microcontroller Units (MCUs/MPUs/SOCs) · PDIP-8

PIC12CE674-04I from Microchip Tech, in a PDIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD power_in Positive supply for logic and I/O pins, with the device operating range stated as 2.5V to 5.5V.
2 GP5/OSC1/CLKIN bidirectional Bidirectional I/O port GP5 that serves as oscillator crystal input or external clock source input (GPIO in INTRC mode only), with a Schmitt trigger input for EXTRC oscillator mode.
3 GP4/OSC2/AN3/CLKOUT bidirectional Bidirectional I/O port GP4 that serves as oscillator crystal output (HS, XT and LP modes only), analog input 3, or CLKOUT at 1/4 the OSC1 frequency in EXTRC and INTRC modes.
4 GP3/MCLR/VPP input Input port GP3 that serves as active-low master clear (reset) input or programming voltage input, where the voltage on MCLR/VPP must not exceed VDD during normal device operation and the weak pull-up is always on when configured as MCLR.
5 GP2/T0CKI/AN2/INT bidirectional Bidirectional I/O port GP2 that can be configured as the Timer0 clock input T0CKI or the external interrupt INT, and also serves as analog input 2, with a Schmitt trigger buffer.
6 GP1/AN1/VREF bidirectional Bidirectional I/O port GP1 that serves as analog input 1 or voltage reference VREF, with software-selectable internal weak pull-up and interrupt-on-pin change, and a Schmitt trigger input when used in serial programming mode.
7 GP0/AN0 bidirectional Bidirectional I/O port GP0 that serves as analog input 0 and serial programming data, with software-selectable internal weak pull-up and interrupt-on-pin change, and a Schmitt trigger input when used in serial programming mode.
8 VSS power_in Ground reference for logic and I/O pins.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package PDIP-8
Category Single Chip Microcomputer/Microcontroller
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient temperature under bias -40 125 °C 89
Storage temperature -65 150 °C 89
Voltage on VDD with respect to VSS 0 7 V 89
Voltage on MCLR with respect to VSS 0 14 V Note 2 89
Voltage on any pin with respect to VSS (except VDD and MCLR) -0.3 V Printed maximum is (VDD + 0.3V); except VDD and MCLR 89
Maximum current into VDD pin 150 mA 89
Input clamp current IIK 20 mA VI < 0 or VI > VDD 89
Output clamp current IOK 20 mA VO < 0 or VO > VDD 89
Maximum output current sunk by any I/O pin 25 mA 89
Maximum output current sourced by any I/O pin 25 mA 89
Operating temperature (industrial) TA -40 85 °C Industrial range, -40°C ≤ TA ≤ +85°C 92
Supply Voltage VDD 3 5.5 V 92
RAM Data Retention Voltage VDR 1.5 V Device in SLEEP mode 92
VDD Rise Rate to ensure Power-on Reset SVDD 0.05 V/ms See section on Power-on Reset for details 92
Supply Current, XT and EXTRC mode IDD 1.2 2.5 mA FOSC = 4MHz, VDD = 3.0V, XT and EXTRC mode (Note 4) 92
Supply Current, INTRC mode IDD 1.2 2.5 mA FOSC = 4MHz, VDD = 3.0V, INTRC mode (Note 6) 92
Supply Current, LP mode, Industrial Temperature IDD 19 37 µA FOSC = 32kHz, VDD = 3.0V, WDT disabled, LP mode, Industrial Temperature 92
Power-down Current, Industrial, 3.0V IPD 0.25 7 µA VDD = 3.0V, Industrial, WDT disabled 92
Power-down Current, Industrial, 5.5V IPD 0.8 9 µA VDD = 5.5V, Industrial, WDT disabled 92
Watchdog Timer Current, Industrial IWDT 2.2 6 µA VDD = 3.0V, Industrial 92
Supply Current during read/write to EEPROM peripheral IEE 0.1 0.2 mA FOSC = 4MHz, VDD = 5.5V, SCL = 400kHz 92
Input Low Voltage, I/O ports with TTL buffer VIL 0.8 V For 4.5V ≤ VDD ≤ 5.5V 95
Input High Voltage, I/O ports with TTL buffer VIH 2 V 4.5V ≤ VDD ≤ 5.5V 95
Input Leakage Current, I/O ports IIL 1 µA Vss ≤ VPIN ≤ VDD, Pin at hi-impedance 95
Input Leakage Current, GP3/MCLR IIL 30 µA Vss ≤ VPIN ≤ VDD (Note 5) 95
Input Leakage Current, GP3 with pull-up disabled IIL 5 µA Vss ≤ VPIN ≤ VDD (Note 6) 95
Input Leakage Current, GP2/T0CKI IIL 5 µA Vss ≤ VPIN ≤ VDD 95
Input Leakage Current, OSC1 IIL 5 µA Vss ≤ VPIN ≤ VDD, XT, HS and LP osc configuration 95
GPIO weak pull-up current IPUR 50 250 400 µA AVDD = 5V, VPIN = VSS 95
MCLR pull-up current 30 µA AVDD = 5V, VPIN = VSS 95
Output Low Voltage, I/O ports VOL 0.6 V IOL = 8.5 mA, VDD = 4.5V, -40C to +85C 95
Output Low Voltage, OSC2/CLKOUT VOL 0.6 V IOL = 1.6 mA, VDD = 4.5V, -40C to +85C 95
OSC2 pin capacitive loading COSC2 15 pF In XT and LP modes when external clock is used to drive OSC1 96
All I/O pins capacitive loading CIO 50 pF 96
External CLKIN Frequency FOSC 4 MHz XT and EXTRC osc mode 100
External CLKIN Frequency FOSC 200 kHz LP osc mode 100
Oscillator Frequency FOSC 4 MHz EXTRC osc mode 100
Oscillator Frequency FOSC 0.455 4 MHz XT osc mode 100
Oscillator Frequency FOSC 4 4 MHz HS osc mode (PIC12CE67X-04) 100
Oscillator Frequency FOSC 5 200 kHz LP osc mode 100
Internal Calibrated RC Frequency 3.65 4 4.28 MHz VDD = 5.0V 101
Instruction Cycle Time TCY 400 ns TCY = 4/FOSC 100
OSC1 to CLKOUT TosH2ckL 75 200 ns Note 1 102
CLKOUT rise time TckR 35 100 ns Note 1 102
OSC1 (Q1 cycle) to Port out valid TosH2ioV 50 150 ns 102
OSC1 (Q2 cycle) to Port input invalid (I/O in hold time) TosH2ioI 100 ns PIC12C67X 102
Port output rise time TioR 10 40 ns PIC12C67X 102
Port output fall time TioF 10 40 ns PIC12C67X 102
T0CKI High Pulse Width, with prescaler Tt0H 10 ns With Prescaler; must also meet parameter 42 104
A/D clock period (TOSC based) TAD 1.6 µs TOSC based, VREF ≥ 3.0V 106
A/D clock period (A/D RC mode) TAD 2 4 6 µs A/D RC Mode 106
Conversion time (not including S/H time) TCNV 11 11 TAD 106
Acquisition time TACQ 5 µs Note 2; minimum time is the amplifier setting time 106
Total absolute error EABS 1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF 105
Recommended impedance of analog voltage source ZAIN 10 kΩ 105

CAD (KiCad official)

  • Symbol: PIC12CE674-04I
  • Footprint: Package_DIP:DIP-8_W7.62mm
  • 3D model: PDIP-8 (KiCad packages3D, STEP)
  • 3D model files: pic12ce674-04i-etched.step / pic12ce674-04i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pic12ce674-04i.step / pic12ce674-04i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (130 pp, sha256 e9cddfd1ac7c837d, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF