main
Ray Publish 0.1.0 a902660

PI6CG33402ZHIEX

Diodes Incorporated · Clock Generators / Frequency Synthesizers / PLL · TQFN-32-EP(5x5)

PI6CG33402ZHIEX from Diodes Incorporated, in a TQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground pin for the device (GND is also listed on pins 15, 26 and 30).
2 XTAL_IN/CLK input Crystal input or CMOS reference input, with a 25MHz input frequency specified for the crystal or CMOS reference.
3 XTAL_OUT output Crystal output, used with a 25MHz fundamental crystal (CL=8pF recommended) connected between XTAL_IN/CLK and XTAL_OUT.
4 VDD_OSC power_in Power supply for oscillator circuitry, nominal 3.3V, with a 3.135V to 3.465V supply range.
5 VDD_REFOUT power_in Power supply for the buffered CMOS REFOUT output, nominal 3.3V, with a 3.135V to 3.465V supply range.
6 SADR/REFOUT bidirectional Latched at first application of PD# to select the SMBus address (0 = 1101000, 1 = 1101010) or LVCMOS REFOUT; has an internal pulldown.
7 GND_REF power_in Ground for REFOUT.
8 GND_DIG power_in Ground for digital circuitry.
9 VDD_DIG power_in Power supply for digital circuitry, nominal 3.3V, with a 3.135V to 3.465V supply range.
10 SCLK input SMBus clock input, CMOS and 3.3V tolerant.
11 SDATA bidirectional SMBus data line, CMOS and 3.3V tolerant; SMBus input high voltage limit is 3.6V.
12 OE0# input Active-low output enable for the Q0 pair (1 = disable outputs, 0 = enable outputs), with an internal pulldown.
13 Q0+ output HCSL differential true clock output at 100MHz with on-chip termination, default ZOUT of 85Ω, blocked until the PLL is locked.
14 Q0- output HCSL differential complementary clock output paired with Q0+ at 100MHz with on-chip termination.
15 GND power_in Ground pin for the device.
16 VDDO power_in Power supply for the differential outputs, nominal 3.3V, with a 3.135V to 3.465V supply range (VDDO is also on pin 25).
17 OE1# input Active-low output enable for the Q1 pair (1 = disable outputs, 0 = enable outputs), with an internal pulldown.
18 Q1+ output HCSL differential true clock output at 100MHz with on-chip termination, default ZOUT of 85Ω, blocked until the PLL is locked.
19 Q1- output HCSL differential complementary clock output paired with Q1+ at 100MHz with on-chip termination.
20 GNDA power_in Ground for analog circuitry.
21 VDDA power_in Power supply for analog circuitry, nominal 3.3V, with a 3.135V to 3.465V supply range.
22 Q2+ output HCSL differential true clock output at 100MHz with on-chip termination, default ZOUT of 85Ω, blocked until the PLL is locked.
23 Q2- output HCSL differential complementary clock output paired with Q2+ at 100MHz with on-chip termination.
24 OE2# input Active-low output enable for the Q2 pair (1 = disable outputs, 0 = enable outputs), with an internal pulldown.
25 VDDO power_in Power supply for the differential outputs, nominal 3.3V, with a 3.135V to 3.465V supply range.
26 GND power_in Ground pin for the device.
27 Q3+ output HCSL differential true clock output at 100MHz with on-chip termination, default ZOUT of 85Ω, blocked until the PLL is locked.
28 Q3- output HCSL differential complementary clock output paired with Q3+ at 100MHz with on-chip termination.
29 OE3# input Active-low output enable for the Q3 pair (1 = disable outputs, 0 = enable outputs), with an internal pulldown.
30 GND power_in Ground pin for the device.
31 PD# input Low enters Power Down Mode and a subsequent high exits it; a high assertion also samples the latched inputs and starts up on first high, with an internal pullup.
32 SS_SEL_TRI input Tri-level latched input selecting spread at power-up (1 = -0.5%, M = -0.25%, 0 = spread off), with an internal pulldown.
33 ePad passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Diodes Incorporated
Package TQFN-32-EP(5x5)
Category Clock and Timing
Pins 33

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage Temperature -65 150 °C 5
Supply Voltage to Ground Potential VDDxx -0.5 4.6 V 5
Input Voltage -0.5 4.6 V VDD+0.5V, not exceed 4.6V 5
SMBus Input High Voltage 3.6 V 5
ESD Protection (HBM) 2000 V 5
Max Junction Temperature 125 °C 5
Power Supply Voltage VDDO, VDDA, VDD_OSC, VDD_DIG, VDD_REFOUT 3.135 3.3 3.465 V 5
Ambient Temperature TA -40 85 °C Industrial grade 5
Analog Power Supply Current IDDA 22 25 mA All outputs active @ 100MHz 5
Power Supply Current IDD 13 16 mA All VDD, except VDDA and VDDO, All outputs active @ 100MHz 5
IO Power Supply Current IDDO 20 25 mA VDDO, All outputs active @ 100MHz 5
Thermal Resistance Junction to Ambient θJA 44.7 °C/W Still air 22
Thermal Resistance Junction to Case θJC 21.7 °C/W 22
Output Voltage High VOH 660 784 850 mV Statistical measurement on single-ended signal using oscilloscope math function 9
Output Voltage Low VOL -150 150 mV 9
Output Voltage Maximum VOMAX 816 1150 mV Measurement on single-ended signal using absolute value 9
Output Voltage Minimum VOMIN -300 -42 mV 9
Output Cross Voltage VOC 250 430 550 mV 9
VOC Magnitude Change DVOC 12 140 mV 9
Slew Rate (fast setting) tRF 2.5 3.2 4 V/ns Scope averaging on fast setting 9
Slew Rate (slow setting) tRF 2.2 3 3.7 V/ns Scope averaging on slow setting 9
Slew Rate Matching DtRF 7 15 % Scope averaging on 9
Duty Cycle (HCSL) tDC 45 50 55 % Measured differentially, PLL Mode 9
Output Skew tSKEW 20 50 ps Averaging on, VT = 50% 9
Cycle-to-Cycle Jitter tjc-c 20 50 ps 9
Integrated Phase Jitter (RMS) tjPHASE 20 30 86 ps(p-p) PCIe 1.0 10
Integrated Phase Jitter (RMS) tjPHASE 0.08 0.1 3 ps PCIe 2.0 Low Band, 10kHz < f < 1.5MHz 10
Integrated Phase Jitter (RMS) tjPHASE 0.99 1.3 3.1 ps PCIe 2.0 High Band, 1.5MHz < f < Nyquist (50MHz) 10
Integrated Phase Jitter (RMS) tjPHASE 0.32 0.42 1 ps PCIe 3.0 Common Clock Architecture (PLL BW of 2-4 or 2-5MHz, CDR = 10MHz) 10
Integrated Phase Jitter (RMS) tjPHASE 0.16 0.21 0.7 ps PCIe 3.0 Separate Reference No Spread (PLL BW of 2-4 or 2-5MHz, CDR =10 MHz) 10
Integrated Phase Jitter (RMS) tjPHASE 0.32 0.4 0.5 ps PCIe 4.0 (PLL BW of 2-4 or 2-5MHz, CDR = 10MHz) 10
Integrated Phase Jitter (RMS) tjPHASE 0.02 0.05 0.15 ps PCIe 5.0 (PLL BW of 500k to 1.8MHz. CDR = 20MHz) 10
Integrated Phase Jitter (RMS), -0.25% Spread tjPHSRISG2 0.6 0.92 2 ps PCIe 2.0, Separate Reference Independent Spread (PLL BW of 16MHz, CDR=5MHz) 10
Integrated Phase Jitter (RMS), -0.25% Spread tjPHSRISG3 0.32 0.4 0.7 ps PCIe 3.0, Separate Reference Independent Spread (PLL BW of 2-4MHz or 2-5MHz, CDR=10MHz) 10
Integrated Phase Jitter (RMS), -0.5% Spread tjPHSRISG2 0.8 1.1 2 ps PCIe 2.0, Separate Reference Independent Spread (PLL BW of 16MHz, CDR=5MHz) 10
Integrated Phase Jitter (RMS), -0.5% Spread tjPHSRISG3 0.35 0.6 0.7 ps PCIe 3.0, Separate Reference Independent Spread (PLL BW of 2-4MHz or 2-5MHz, CDR=10MHz) 10
Input Low Voltage VIL -0.3 V Single-ended inputs, except SMBus 7
Input High Current IIH 5 µA Single-ended inputs, VIN = VDD 7
Input Low Current IIL -5 µA Single-ended inputs, VIN = 0V 7
Input High Current (with pullup/pulldown) IIH 50 µA Single-ended inputs with pullup/pulldown resistor, VIN = VDD 7
Input Low Current (with pullup/pulldown) IIL -50 µA Single-ended inputs with pullup/pulldown resistor, VIN = 0V 7
Input Capacitance CIN 1.5 5 pF 7
Input Rise Time tRIN 5 ns Single-ended inputs 8
Input Fall Time tFIN 5 ns Single-ended inputs 8
Clock Stabilization tSTAB 0.75 1 ms From power up and after input clock stabilization or deassertion of PD# to first clock 8
Output Enable Latency tOELAT 1 3 clocks Q start after OE# assertion; Q stop after OE# deassertion 8
PD# Deassertion Latency tPDLAT 20 300 µs Differential outputs enable after PD# deassertion 8
REFOUT Slew Rate (Byte 3 = 1F) tSLEW 0.9 1.4 2 V/ns Byte 3 = 1F, 20% to 80% of VDDREF 8
REFOUT Duty Cycle tDC 45 50 55 % VT = VDD/2V, driven by a Xtal 8
REFOUT Cycle-Cycle Jitter tJITCC 70 150 ps VT = VDD/2V, driven by a Xtal 8
REFOUT Phase Jitter, RMS (SSC off) tJITPH 0.16 0.3 ps 12kHz to 5MHz, SSC off, driven by a Xtal 8
REFOUT Phase Jitter, RMS (SSC on) tJITPH 0.9 1.5 ps 12kHz to 5MHz, SSC on, driven by a Xtal 8
Noise Floor tJITN -149 -135 dBc/Hz 1kHz offset, driven by a Xtal 8
SMBus Nominal Bus Voltage VDDSMB 2.7 3.6 V 6
SMBus Input High Voltage VIHSMB 2.1 3.6 V SMBus, VDDSMB = 3.3V 6
SMBus Input Low Voltage VILSMB 0.8 V SMBus, VDDSMB = 3.3V 6
SMBus Output Low Voltage VOLSMB 0.4 V SMBus at ISMBSINK 6
SS Modulation Frequency fMOD 30 31.8 33 kHz Triangular modulation 6
Pin Inductance LPIN 7 nH 6
Equivalent Series Resistance ESR 50 W ESR value is dependent upon frequency of oscillation 6

CAD (KiCad official)

  • Symbol: PI6CG33402ZHIEX
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: TQFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: pi6cg33402zhiex-etched.step / pi6cg33402zhiex-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pi6cg33402zhiex.step / pi6cg33402zhiex.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Diodes Incorporated datasheet (24 pp, sha256 94af1f3519d31368, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF