component
PCF8579HT/1
Public Made by Adomby adom
NXP Semicon LCD Drivers, TQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
834acc7
PCF8579HT
NXP Semicon · LCD Drivers · TQFP-64(10x10)
PCF8579HT from NXP Semicon, in a TQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C5 | output | LCD column driver output C5; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 2 | C4 | output | LCD column driver output C4; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 3 | C3 | output | LCD column driver output C3; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 4 | C2 | output | LCD column driver output C2; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 5 | C1 | output | LCD column driver output C1; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 6 | C0 | output | LCD column driver output C0; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 7 | SDA | bidirectional | I2C-bus serial data input/output; ESD protection does not use a diode to VDD to allow partial VDD shutdown. |
| 8 | SCL | input | I2C-bus serial clock input; ESD protection does not use a diode to VDD to allow partial VDD shutdown. |
| 9 | SYNC | output | Cascade synchronization signal, used to keep the timing of cascaded PCF8579 devices in step with the PCF8578. |
| 10 | CLK | bidirectional | External clock input/output; the clock frequency is specified as up to 10 kHz at a 50 % duty factor. |
| 11 | VSS | power_in | Ground supply, 0 V reference for VDD and the I2C-bus. |
| 12 | TEST | input | Test pin, which must be connected to VSS. |
| 13 | SA0 | input | I2C-bus slave address input (bit 0); tie to VSS for logic 0 or VDD for logic 1. |
| 14 | A3 | input | I2C-bus hardware subaddress input (bit 3), tied to VSS or VDD to set the device subaddress. |
| 15 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 16 | A2 | input | I2C-bus hardware subaddress input (bit 2), tied to VSS or VDD to set the device subaddress. |
| 17 | A1 | input | I2C-bus hardware subaddress input (bit 1), tied to VSS or VDD to set the device subaddress. |
| 18 | A0 | input | I2C-bus hardware subaddress input (bit 0), tied to VSS or VDD to set the device subaddress. |
| 19 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 20 | VDD | power_in | Logic supply voltage, 2.5 V to 6.0 V with respect to VSS. |
| 21 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 22 | V3 | power_in | LCD bias voltage input V3; must be within the LCD supply range of VDD − 9 V to VDD − 3.5 V. |
| 23 | V4 | power_in | LCD bias voltage input V4; must be within the LCD supply range of VDD − 9 V to VDD − 3.5 V. |
| 24 | VLCD | power_in | LCD supply voltage, VDD − 9 V to VDD − 3.5 V. |
| 25 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 26 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 27 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 28 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 29 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 30 | C39 | output | LCD column driver output C39; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 31 | C38 | output | LCD column driver output C38; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 32 | C37 | output | LCD column driver output C37; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 33 | C36 | output | LCD column driver output C36; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 34 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 35 | C35 | output | LCD column driver output C35; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 36 | C34 | output | LCD column driver output C34; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 37 | C33 | output | LCD column driver output C33; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 38 | C32 | output | LCD column driver output C32; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 39 | C31 | output | LCD column driver output C31; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 40 | C30 | output | LCD column driver output C30; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 41 | C29 | output | LCD column driver output C29; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 42 | C28 | output | LCD column driver output C28; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 43 | C27 | output | LCD column driver output C27; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 44 | C26 | output | LCD column driver output C26; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 45 | C25 | output | LCD column driver output C25; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 46 | C24 | output | LCD column driver output C24; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 47 | C23 | output | LCD column driver output C23; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 48 | C22 | output | LCD column driver output C22; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 49 | C21 | output | LCD column driver output C21; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 50 | C20 | output | LCD column driver output C20; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 51 | C19 | output | LCD column driver output C19; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 52 | C18 | output | LCD column driver output C18; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 53 | C17 | output | LCD column driver output C17; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 54 | C16 | output | LCD column driver output C16; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 55 | C15 | output | LCD column driver output C15; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 56 | C14 | output | LCD column driver output C14; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 57 | C13 | output | LCD column driver output C13; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 58 | C12 | output | LCD column driver output C12; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 59 | C11 | output | LCD column driver output C11; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 60 | C10 | output | LCD column driver output C10; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 61 | C9 | output | LCD column driver output C9; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 62 | C8 | output | LCD column driver output C8; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 63 | C7 | output | LCD column driver output C7; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 64 | C6 | output | LCD column driver output C6; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | TQFP-64(10x10) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD supply voltage | VDD | 2.5 | 6 | V | 25 | ||
| IDD supply current | IDD | 9 | 20 | µA | fclk = 2 kHz | 25 | |
| VPOR power-on reset voltage | VPOR | 1.3 | 1.8 | V | 25 | ||
| IOL LOW-level output current at pin SDA | IOL | 3 | mA | VOL = 0.4 V; VDD = 5 V | 25 | ||
| IL leakage current at pins SDA, SCL, SYNC, CLK, TEST and SA0, A0 to A3 | IL | -1 | 1 | mA | Vi = VDD or VSS | 25 | |
| Ci input capacitance at pin SCL and SDA | Ci | 5 | pF | 25 | |||
| IL leakage current at pins V3 and V4 | IL | -2 | 2 | µA | Vi = VDD or VLCD | 25 | |
| DC offset voltage on pins C0 to C39 | Voffset(DC) | -20 | 20 | mV | 25 | ||
| clock frequency | fclk | 10 | kHz | 50 % duty factor | 26 | ||
| driver propagation delay | tPD(drv) | 100 | µs | VDD − VLCD = 9 V; with test load of 45 pF | 26 | ||
| SCL clock frequency | fSCL | 100 | kHz | 26 | |||
| spike pulse width | tw(spike) | 100 | ns | 26 | |||
| bus free time between a STOP and START condition | tBUF | 4.7 | µs | 26 | |||
| set-up time for a repeated START condition | tSU;STA | 4.7 | µs | 26 | |||
| hold time (repeated) START condition | tHD;STA | 4 | µs | 26 | |||
| LOW period of the SCL clock | tLOW | 4.7 | µs | 26 | |||
| HIGH period of the SCL clock | tHIGH | 4 | µs | 26 | |||
| rise time of both SDA and SCL signals | tr | 1 | µs | 26 | |||
| fall time of both SDA and SCL signals | tf | 0.3 | µs | 26 | |||
| data set-up time | tSU;DAT | 250 | ns | 26 | |||
| data hold time | tHD;DAT | 0 | ns | 26 | |||
| set-up time for STOP condition | tSU;STO | 4 | µs | 26 | |||
| supply voltage (VDD related) | VDD | -0.5 | 8 | V | 24 | ||
| LCD supply voltage | VLCD | 8 | V | 24 | |||
| input voltage (VDD related; SDA, SCL, CLK, TEST, SA0, OSC) | VI | -0.5 | 8 | V | VDD related | 24 | |
| input voltage (VLCD related; V3 and V4) | VI | 8 | V | VLCD related; V3 and V4 | 24 | ||
| output voltage (VDD related; SYNC and CLK) | VO | -0.5 | 8 | V | VDD related; SYNC and CLK | 24 | |
| output voltage (VLCD related; R0 to R7, R8/C8 to R31/C31 and C32 to C39) | VO | 8 | V | VLCD related; R0 to R7, R8/C8 to R31/C31 and C32 to C39 | 24 | ||
| input current | II | -10 | 10 | mA | 24 | ||
| output current | IO | -10 | 10 | mA | 24 | ||
| supply current | IDD | -50 | 50 | mA | 24 | ||
| LCD supply current | IDD(LCD) | -50 | 50 | mA | 24 | ||
| ground supply current | ISS | -50 | 50 | mA | 24 | ||
| total power dissipation per package | Ptot | 400 | mW | 24 | |||
| output power | Po | 100 | mW | 24 | |||
| storage temperature | Tstg | -65 | 150 | °C | 24 | ||
| ambient operating temperature | Tamb | -40 | 85 | °C | Operating range stated in the header of Tables 14 and 15 | 25 |
CAD (KiCad official)
- Symbol:
PCF8579HT - Footprint:
Package_QFP:TQFP-64_10x10mm_P0.5mm - 3D model: TQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
pcf8579ht-1-etched.step/pcf8579ht-1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pcf8579ht-1.step/pcf8579ht-1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: NXP Semicon datasheet (41 pp, sha256
0078fa85a48fd663, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PCF8579HT
**NXP Semicon** · LCD Drivers · TQFP-64(10x10)
PCF8579HT from NXP Semicon, in a TQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C5 | output | LCD column driver output C5; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 2 | C4 | output | LCD column driver output C4; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 3 | C3 | output | LCD column driver output C3; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 4 | C2 | output | LCD column driver output C2; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 5 | C1 | output | LCD column driver output C1; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 6 | C0 | output | LCD column driver output C0; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 7 | SDA | bidirectional | I2C-bus serial data input/output; ESD protection does not use a diode to VDD to allow partial VDD shutdown. |
| 8 | SCL | input | I2C-bus serial clock input; ESD protection does not use a diode to VDD to allow partial VDD shutdown. |
| 9 | SYNC | output | Cascade synchronization signal, used to keep the timing of cascaded PCF8579 devices in step with the PCF8578. |
| 10 | CLK | bidirectional | External clock input/output; the clock frequency is specified as up to 10 kHz at a 50 % duty factor. |
| 11 | VSS | power_in | Ground supply, 0 V reference for VDD and the I2C-bus. |
| 12 | TEST | input | Test pin, which must be connected to VSS. |
| 13 | SA0 | input | I2C-bus slave address input (bit 0); tie to VSS for logic 0 or VDD for logic 1. |
| 14 | A3 | input | I2C-bus hardware subaddress input (bit 3), tied to VSS or VDD to set the device subaddress. |
| 15 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 16 | A2 | input | I2C-bus hardware subaddress input (bit 2), tied to VSS or VDD to set the device subaddress. |
| 17 | A1 | input | I2C-bus hardware subaddress input (bit 1), tied to VSS or VDD to set the device subaddress. |
| 18 | A0 | input | I2C-bus hardware subaddress input (bit 0), tied to VSS or VDD to set the device subaddress. |
| 19 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 20 | VDD | power_in | Logic supply voltage, 2.5 V to 6.0 V with respect to VSS. |
| 21 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 22 | V3 | power_in | LCD bias voltage input V3; must be within the LCD supply range of VDD − 9 V to VDD − 3.5 V. |
| 23 | V4 | power_in | LCD bias voltage input V4; must be within the LCD supply range of VDD − 9 V to VDD − 3.5 V. |
| 24 | VLCD | power_in | LCD supply voltage, VDD − 9 V to VDD − 3.5 V. |
| 25 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 26 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 27 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 28 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 29 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 30 | C39 | output | LCD column driver output C39; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 31 | C38 | output | LCD column driver output C38; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 32 | C37 | output | LCD column driver output C37; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 33 | C36 | output | LCD column driver output C36; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 34 | n.c. | unconnected | Not connected; reserved pin, do not connect. |
| 35 | C35 | output | LCD column driver output C35; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 36 | C34 | output | LCD column driver output C34; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 37 | C33 | output | LCD column driver output C33; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 38 | C32 | output | LCD column driver output C32; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 39 | C31 | output | LCD column driver output C31; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 40 | C30 | output | LCD column driver output C30; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 41 | C29 | output | LCD column driver output C29; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 42 | C28 | output | LCD column driver output C28; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 43 | C27 | output | LCD column driver output C27; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 44 | C26 | output | LCD column driver output C26; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 45 | C25 | output | LCD column driver output C25; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 46 | C24 | output | LCD column driver output C24; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 47 | C23 | output | LCD column driver output C23; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 48 | C22 | output | LCD column driver output C22; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 49 | C21 | output | LCD column driver output C21; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 50 | C20 | output | LCD column driver output C20; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 51 | C19 | output | LCD column driver output C19; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 52 | C18 | output | LCD column driver output C18; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 53 | C17 | output | LCD column driver output C17; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 54 | C16 | output | LCD column driver output C16; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 55 | C15 | output | LCD column driver output C15; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 56 | C14 | output | LCD column driver output C14; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 57 | C13 | output | LCD column driver output C13; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 58 | C12 | output | LCD column driver output C12; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 59 | C11 | output | LCD column driver output C11; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 60 | C10 | output | LCD column driver output C10; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 61 | C9 | output | LCD column driver output C9; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 62 | C8 | output | LCD column driver output C8; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 63 | C7 | output | LCD column driver output C7; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
| 64 | C6 | output | LCD column driver output C6; leave open-circuit if unused, with output voltage limits of VDD − 11 V to +8.0 V relative to VLCD. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | TQFP-64(10x10) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD supply voltage | VDD | 2.5 | | 6 | V | | 25 |
| IDD supply current | IDD | | 9 | 20 | µA | fclk = 2 kHz | 25 |
| VPOR power-on reset voltage | VPOR | | 1.3 | 1.8 | V | | 25 |
| IOL LOW-level output current at pin SDA | IOL | 3 | | | mA | VOL = 0.4 V; VDD = 5 V | 25 |
| IL leakage current at pins SDA, SCL, SYNC, CLK, TEST and SA0, A0 to A3 | IL | -1 | | 1 | mA | Vi = VDD or VSS | 25 |
| Ci input capacitance at pin SCL and SDA | Ci | | | 5 | pF | | 25 |
| IL leakage current at pins V3 and V4 | IL | -2 | | 2 | µA | Vi = VDD or VLCD | 25 |
| DC offset voltage on pins C0 to C39 | Voffset(DC) | -20 | | 20 | mV | | 25 |
| clock frequency | fclk | | | 10 | kHz | 50 % duty factor | 26 |
| driver propagation delay | tPD(drv) | | | 100 | µs | VDD − VLCD = 9 V; with test load of 45 pF | 26 |
| SCL clock frequency | fSCL | | | 100 | kHz | | 26 |
| spike pulse width | tw(spike) | | | 100 | ns | | 26 |
| bus free time between a STOP and START condition | tBUF | 4.7 | | | µs | | 26 |
| set-up time for a repeated START condition | tSU;STA | 4.7 | | | µs | | 26 |
| hold time (repeated) START condition | tHD;STA | 4 | | | µs | | 26 |
| LOW period of the SCL clock | tLOW | 4.7 | | | µs | | 26 |
| HIGH period of the SCL clock | tHIGH | 4 | | | µs | | 26 |
| rise time of both SDA and SCL signals | tr | | | 1 | µs | | 26 |
| fall time of both SDA and SCL signals | tf | | | 0.3 | µs | | 26 |
| data set-up time | tSU;DAT | 250 | | | ns | | 26 |
| data hold time | tHD;DAT | 0 | | | ns | | 26 |
| set-up time for STOP condition | tSU;STO | 4 | | | µs | | 26 |
| supply voltage (VDD related) | VDD | -0.5 | | 8 | V | | 24 |
| LCD supply voltage | VLCD | | | 8 | V | | 24 |
| input voltage (VDD related; SDA, SCL, CLK, TEST, SA0, OSC) | VI | -0.5 | | 8 | V | VDD related | 24 |
| input voltage (VLCD related; V3 and V4) | VI | | | 8 | V | VLCD related; V3 and V4 | 24 |
| output voltage (VDD related; SYNC and CLK) | VO | -0.5 | | 8 | V | VDD related; SYNC and CLK | 24 |
| output voltage (VLCD related; R0 to R7, R8/C8 to R31/C31 and C32 to C39) | VO | | | 8 | V | VLCD related; R0 to R7, R8/C8 to R31/C31 and C32 to C39 | 24 |
| input current | II | -10 | | 10 | mA | | 24 |
| output current | IO | -10 | | 10 | mA | | 24 |
| supply current | IDD | -50 | | 50 | mA | | 24 |
| LCD supply current | IDD(LCD) | -50 | | 50 | mA | | 24 |
| ground supply current | ISS | -50 | | 50 | mA | | 24 |
| total power dissipation per package | Ptot | | | 400 | mW | | 24 |
| output power | Po | | | 100 | mW | | 24 |
| storage temperature | Tstg | -65 | | 150 | °C | | 24 |
| ambient operating temperature | Tamb | -40 | | 85 | °C | Operating range stated in the header of Tables 14 and 15 | 25 |
## CAD (KiCad official)
- Symbol: `PCF8579HT`
- Footprint: `Package_QFP:TQFP-64_10x10mm_P0.5mm`
- 3D model: TQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `pcf8579ht-1-etched.step` / `pcf8579ht-1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pcf8579ht-1.step` / `pcf8579ht-1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [NXP Semicon datasheet](https://www.nxp.com/docs/en/data-sheet/PCF8579.pdf) (41 pp, sha256 `0078fa85a48fd663`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pcf8579ht-1-datasheet.pdf)