main
Ray
Publish 0.1.0
026082c
PCA9531D
NXP Semicon · LED Drivers · SOIC-16
PCA9531D from NXP Semicon, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Hardware address input 0 sets the programmable bit of the slave address and has no internal pull-up, so it must be pulled HIGH or LOW. |
| 2 | A1 | input | Hardware address input 1 sets the programmable bit of the slave address and has no internal pull-up, so it must be pulled HIGH or LOW. |
| 3 | A2 | input | Hardware address input 2 sets the programmable bit of the slave address and has no internal pull-up, so it must be pulled HIGH or LOW. |
| 4 | LED0 | bidirectional | Open-drain LED driver 0 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 5 | LED1 | bidirectional | Open-drain LED driver 1 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 6 | LED2 | bidirectional | Open-drain LED driver 2 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 7 | LED3 | bidirectional | Open-drain LED driver 3 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 8 | VSS | power_in | Supply ground; it must be connected to supply ground for proper device operation. |
| 9 | LED4 | bidirectional | Open-drain LED driver 4 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 10 | LED5 | bidirectional | Open-drain LED driver 5 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 11 | LED6 | bidirectional | Open-drain LED driver 6 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 12 | LED7 | bidirectional | Open-drain LED driver 7 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 13 | RESET | input | Active LOW reset input; asserting it, or power-on reset, returns the registers to their default state with all LED bits HIGH (LED off). |
| 14 | SCL | input | I2C-bus serial clock line with noise filter, supporting clock frequencies from 0 Hz to 400 kHz. |
| 15 | SDA | bidirectional | I2C-bus serial data line with noise filter, compatible with SMBus. |
| 16 | VDD | power_in | Supply voltage with an operating range of 2.3 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | SOIC-16 |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD supply voltage (absolute maximum) | VDD | -0.5 | 6 | V | 13 | ||
| VI/O voltage on an input/output pin (absolute maximum; min printed as VSS − 0.5) | VI/O | -0.5 | 5.5 | V | 13 | ||
| output current on pin LEDn (absolute maximum, printed ±25) | IO(LEDn) | -25 | 25 | mA | 13 | ||
| ground supply current (absolute maximum) | ISS | 200 | mA | 13 | |||
| total power dissipation (absolute maximum) | Ptot | 400 | mW | 13 | |||
| storage temperature (absolute maximum) | Tstg | -65 | 150 | °C | 13 | ||
| ambient temperature operating (absolute maximum) | Tamb | -40 | 85 | °C | 13 | ||
| VDD supply voltage | VDD | 2.3 | 5.5 | V | 14 | ||
| IDD supply current | IDD | 350 | 500 | µA | operating mode; VDD = 5.5 V; VI =VDD or VSS; fSCL = 100 kHz | 14 | |
| standby current | Istb | 1.9 | 5 | µA | Standby mode; VDD = 5.5 V; VI =VDD or VSS; fSCL = 0 kHz | 14 | |
| additional quiescent supply current | ∆IDD | 200 | µA | Standby mode; VDD = 5.5 V; LED I/O at VI = 4.3 V; fSCL = 0 kHz | 14 | ||
| power-on reset voltage | VPOR | 1.7 | 2.2 | V | no load; VI =VDD or VSS | 14 | |
| LOW-level input voltage (SCL, SDA; max printed as +0.3VDD) | VIL | -0.5 | V | 14 | |||
| HIGH-level input voltage (SCL, SDA; min printed as 0.7VDD) | VIH | 5.5 | V | 14 | |||
| LOW-level output current (SDA) | IOL | 3 | 6.5 | mA | VOL = 0.4 V | 14 | |
| leakage current (SCL, SDA) | IL | -1 | 1 | µA | VI =VDD =VSS | 14 | |
| input capacitance (SCL, SDA) | Ci | 3.7 | 5 | pF | VI =VSS | 14 | |
| I/Os LOW-level input voltage | VIL | -0.5 | 0.8 | V | 14 | ||
| I/Os HIGH-level input voltage | VIH | 2 | 5.5 | V | 14 | ||
| I/Os LOW-level output current | IOL | 9 | mA | VOL = 0.4 V; VDD = 2.3 V | 14 | ||
| I/Os LOW-level output current | IOL | 12 | mA | VOL = 0.4 V; VDD = 3.0 V | 14 | ||
| I/Os LOW-level output current | IOL | 15 | mA | VOL = 0.4 V; VDD = 5.0 V | 14 | ||
| I/Os LOW-level output current | IOL | 20 | mA | VOL = 0.7 V; VDD = 3.0 V | 14 | ||
| I/Os LOW-level output current | IOL | 25 | mA | VOL = 0.7 V; VDD = 5.0 V | 14 | ||
| I/Os input leakage current | ILI | -1 | 1 | µA | VDD = 3.6 V; VI = 0 V or VDD | 14 | |
| I/Os input/output capacitance | Cio | 2.5 | 5 | pF | 14 | ||
| Select inputs A0, A1, A2; RESET LOW-level input voltage | VIL | -0.5 | 0.8 | V | 14 | ||
| A0; RESET HIGH-level input voltage | VIH | 2 | 5.5 | V | 14 | ||
| A1; A2 HIGH-level input voltage (max printed as VDD + 0.5) | VIH | 2 | V | 14 | |||
| Select inputs A0, A1, A2; RESET input leakage current | ILI | -1 | 1 | µA | 14 | ||
| Select inputs A0, A1, A2; RESET input capacitance | Ci | 2.3 | 5 | pF | VI =VSS | 14 | |
| SCL clock frequency (standard-mode) | fSCL | 0 | 100 | kHz | Standard-mode I2C-bus | 16 | |
| SCL clock frequency (fast-mode) | fSCL | 0 | 400 | kHz | Fast-mode I2C-bus | 16 | |
| bus free time between STOP and START (standard-mode) | tBUF | 4.7 | µs | Standard-mode I2C-bus | 16 | ||
| bus free time between STOP and START (fast-mode) | tBUF | 1.3 | µs | Fast-mode I2C-bus | 16 | ||
| hold time (repeated) START condition (standard-mode) | tHD;STA | 4 | µs | Standard-mode I2C-bus | 16 | ||
| hold time (repeated) START condition (fast-mode) | tHD;STA | 0.6 | µs | Fast-mode I2C-bus | 16 | ||
| set-up time for a repeated START condition (standard-mode) | tSU;STA | 4.7 | µs | Standard-mode I2C-bus | 16 | ||
| set-up time for a repeated START condition (fast-mode) | tSU;STA | 0.6 | µs | Fast-mode I2C-bus | 16 | ||
| set-up time for STOP condition (standard-mode) | tSU;STO | 4 | µs | Standard-mode I2C-bus | 16 | ||
| set-up time for STOP condition (fast-mode) | tSU;STO | 0.6 | µs | Fast-mode I2C-bus | 16 | ||
| data hold time (standard-mode) | tHD;DAT | 0 | ns | Standard-mode I2C-bus | 16 | ||
| data hold time (fast-mode) | tHD;DAT | 0 | ns | Fast-mode I2C-bus | 16 | ||
| data set-up time (standard-mode) | tSU;DAT | 250 | ns | Standard-mode I2C-bus | 16 | ||
| data set-up time (fast-mode) | tSU;DAT | 100 | ns | Fast-mode I2C-bus | 16 | ||
| LOW period of the SCL clock (standard-mode) | tLOW | 4.7 | µs | Standard-mode I2C-bus | 16 | ||
| LOW period of the SCL clock (fast-mode) | tLOW | 1.3 | µs | Fast-mode I2C-bus | 16 | ||
| HIGH period of the SCL clock (standard-mode) | tHIGH | 4 | µs | Standard-mode I2C-bus | 16 | ||
| HIGH period of the SCL clock (fast-mode) | tHIGH | 0.6 | µs | Fast-mode I2C-bus | 16 | ||
| pulse width of spikes suppressed by input filter (standard-mode) | tSP | 50 | ns | Standard-mode I2C-bus | 16 | ||
| pulse width of spikes suppressed by input filter (fast-mode) | tSP | 50 | ns | Fast-mode I2C-bus | 16 | ||
| data output valid time | tv(Q) | 200 | ns | 16 | |||
| data input set-up time | tsu(D) | 100 | ns | 16 | |||
| data input hold time | th(D) | 1 | µs | 16 | |||
| reset pulse width | tw(rst) | 6 | ns | 16 | |||
| reset recovery time | trec(rst) | 0 | ns | 16 | |||
| reset time | trst | 400 | ns | 16 |
CAD (KiCad official)
- Symbol:
PCA9531D - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
pca9531d-etched.step/pca9531d-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pca9531d.step/pca9531d.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: NXP Semicon datasheet (27 pp, sha256
556cfc5d2fadb0d4, retrieved 2026-10-26, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# PCA9531D
**NXP Semicon** · LED Drivers · SOIC-16
PCA9531D from NXP Semicon, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Hardware address input 0 sets the programmable bit of the slave address and has no internal pull-up, so it must be pulled HIGH or LOW. |
| 2 | A1 | input | Hardware address input 1 sets the programmable bit of the slave address and has no internal pull-up, so it must be pulled HIGH or LOW. |
| 3 | A2 | input | Hardware address input 2 sets the programmable bit of the slave address and has no internal pull-up, so it must be pulled HIGH or LOW. |
| 4 | LED0 | bidirectional | Open-drain LED driver 0 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 5 | LED1 | bidirectional | Open-drain LED driver 1 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 6 | LED2 | bidirectional | Open-drain LED driver 2 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 7 | LED3 | bidirectional | Open-drain LED driver 3 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 8 | VSS | power_in | Supply ground; it must be connected to supply ground for proper device operation. |
| 9 | LED4 | bidirectional | Open-drain LED driver 4 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 10 | LED5 | bidirectional | Open-drain LED driver 5 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 11 | LED6 | bidirectional | Open-drain LED driver 6 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 12 | LED7 | bidirectional | Open-drain LED driver 7 directly drives an LED to a maximum of 25 mA per bit (100 mA per package); if not used as an LED driver it can serve as a GPIO. |
| 13 | RESET | input | Active LOW reset input; asserting it, or power-on reset, returns the registers to their default state with all LED bits HIGH (LED off). |
| 14 | SCL | input | I2C-bus serial clock line with noise filter, supporting clock frequencies from 0 Hz to 400 kHz. |
| 15 | SDA | bidirectional | I2C-bus serial data line with noise filter, compatible with SMBus. |
| 16 | VDD | power_in | Supply voltage with an operating range of 2.3 V to 5.5 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | SOIC-16 |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD supply voltage (absolute maximum) | VDD | -0.5 | | 6 | V | | 13 |
| VI/O voltage on an input/output pin (absolute maximum; min printed as VSS − 0.5) | VI/O | -0.5 | | 5.5 | V | | 13 |
| output current on pin LEDn (absolute maximum, printed ±25) | IO(LEDn) | -25 | | 25 | mA | | 13 |
| ground supply current (absolute maximum) | ISS | | | 200 | mA | | 13 |
| total power dissipation (absolute maximum) | Ptot | | | 400 | mW | | 13 |
| storage temperature (absolute maximum) | Tstg | -65 | | 150 | °C | | 13 |
| ambient temperature operating (absolute maximum) | Tamb | -40 | | 85 | °C | | 13 |
| VDD supply voltage | VDD | 2.3 | | 5.5 | V | | 14 |
| IDD supply current | IDD | | 350 | 500 | µA | operating mode; VDD = 5.5 V; VI =VDD or VSS; fSCL = 100 kHz | 14 |
| standby current | Istb | | 1.9 | 5 | µA | Standby mode; VDD = 5.5 V; VI =VDD or VSS; fSCL = 0 kHz | 14 |
| additional quiescent supply current | ∆IDD | | | 200 | µA | Standby mode; VDD = 5.5 V; LED I/O at VI = 4.3 V; fSCL = 0 kHz | 14 |
| power-on reset voltage | VPOR | | 1.7 | 2.2 | V | no load; VI =VDD or VSS | 14 |
| LOW-level input voltage (SCL, SDA; max printed as +0.3VDD) | VIL | -0.5 | | | V | | 14 |
| HIGH-level input voltage (SCL, SDA; min printed as 0.7VDD) | VIH | | | 5.5 | V | | 14 |
| LOW-level output current (SDA) | IOL | 3 | 6.5 | | mA | VOL = 0.4 V | 14 |
| leakage current (SCL, SDA) | IL | -1 | | 1 | µA | VI =VDD =VSS | 14 |
| input capacitance (SCL, SDA) | Ci | | 3.7 | 5 | pF | VI =VSS | 14 |
| I/Os LOW-level input voltage | VIL | -0.5 | | 0.8 | V | | 14 |
| I/Os HIGH-level input voltage | VIH | 2 | | 5.5 | V | | 14 |
| I/Os LOW-level output current | IOL | 9 | | | mA | VOL = 0.4 V; VDD = 2.3 V | 14 |
| I/Os LOW-level output current | IOL | 12 | | | mA | VOL = 0.4 V; VDD = 3.0 V | 14 |
| I/Os LOW-level output current | IOL | 15 | | | mA | VOL = 0.4 V; VDD = 5.0 V | 14 |
| I/Os LOW-level output current | IOL | 20 | | | mA | VOL = 0.7 V; VDD = 3.0 V | 14 |
| I/Os LOW-level output current | IOL | 25 | | | mA | VOL = 0.7 V; VDD = 5.0 V | 14 |
| I/Os input leakage current | ILI | -1 | | 1 | µA | VDD = 3.6 V; VI = 0 V or VDD | 14 |
| I/Os input/output capacitance | Cio | | 2.5 | 5 | pF | | 14 |
| Select inputs A0, A1, A2; RESET LOW-level input voltage | VIL | -0.5 | | 0.8 | V | | 14 |
| A0; RESET HIGH-level input voltage | VIH | 2 | | 5.5 | V | | 14 |
| A1; A2 HIGH-level input voltage (max printed as VDD + 0.5) | VIH | 2 | | | V | | 14 |
| Select inputs A0, A1, A2; RESET input leakage current | ILI | -1 | | 1 | µA | | 14 |
| Select inputs A0, A1, A2; RESET input capacitance | Ci | | 2.3 | 5 | pF | VI =VSS | 14 |
| SCL clock frequency (standard-mode) | fSCL | 0 | | 100 | kHz | Standard-mode I2C-bus | 16 |
| SCL clock frequency (fast-mode) | fSCL | 0 | | 400 | kHz | Fast-mode I2C-bus | 16 |
| bus free time between STOP and START (standard-mode) | tBUF | 4.7 | | | µs | Standard-mode I2C-bus | 16 |
| bus free time between STOP and START (fast-mode) | tBUF | 1.3 | | | µs | Fast-mode I2C-bus | 16 |
| hold time (repeated) START condition (standard-mode) | tHD;STA | 4 | | | µs | Standard-mode I2C-bus | 16 |
| hold time (repeated) START condition (fast-mode) | tHD;STA | 0.6 | | | µs | Fast-mode I2C-bus | 16 |
| set-up time for a repeated START condition (standard-mode) | tSU;STA | 4.7 | | | µs | Standard-mode I2C-bus | 16 |
| set-up time for a repeated START condition (fast-mode) | tSU;STA | 0.6 | | | µs | Fast-mode I2C-bus | 16 |
| set-up time for STOP condition (standard-mode) | tSU;STO | 4 | | | µs | Standard-mode I2C-bus | 16 |
| set-up time for STOP condition (fast-mode) | tSU;STO | 0.6 | | | µs | Fast-mode I2C-bus | 16 |
| data hold time (standard-mode) | tHD;DAT | 0 | | | ns | Standard-mode I2C-bus | 16 |
| data hold time (fast-mode) | tHD;DAT | 0 | | | ns | Fast-mode I2C-bus | 16 |
| data set-up time (standard-mode) | tSU;DAT | 250 | | | ns | Standard-mode I2C-bus | 16 |
| data set-up time (fast-mode) | tSU;DAT | 100 | | | ns | Fast-mode I2C-bus | 16 |
| LOW period of the SCL clock (standard-mode) | tLOW | 4.7 | | | µs | Standard-mode I2C-bus | 16 |
| LOW period of the SCL clock (fast-mode) | tLOW | 1.3 | | | µs | Fast-mode I2C-bus | 16 |
| HIGH period of the SCL clock (standard-mode) | tHIGH | 4 | | | µs | Standard-mode I2C-bus | 16 |
| HIGH period of the SCL clock (fast-mode) | tHIGH | 0.6 | | | µs | Fast-mode I2C-bus | 16 |
| pulse width of spikes suppressed by input filter (standard-mode) | tSP | | | 50 | ns | Standard-mode I2C-bus | 16 |
| pulse width of spikes suppressed by input filter (fast-mode) | tSP | | | 50 | ns | Fast-mode I2C-bus | 16 |
| data output valid time | tv(Q) | | | 200 | ns | | 16 |
| data input set-up time | tsu(D) | 100 | | | ns | | 16 |
| data input hold time | th(D) | 1 | | | µs | | 16 |
| reset pulse width | tw(rst) | 6 | | | ns | | 16 |
| reset recovery time | trec(rst) | 0 | | | ns | | 16 |
| reset time | trst | 400 | | | ns | | 16 |
## CAD (KiCad official)
- Symbol: `PCA9531D`
- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`
- 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files: `pca9531d-etched.step` / `pca9531d-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `pca9531d.step` / `pca9531d.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [NXP Semicon datasheet](https://www.nxp.com/docs/en/data-sheet/PCA9531D.pdf) (27 pp, sha256 `556cfc5d2fadb0d4`, retrieved 2026-10-26, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/pca9531d-datasheet.pdf)