component
PCA82C250MM
Public Made by Adomby adom
HGSEMI CAN Transceivers, MSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPCA82C250MM
HGSEMI · CAN Transceivers · MSOP-8
PCA82C250MM from HGSEMI, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TXD | input | Transmit data input: a low level drives the bus dominant, an internal pull-up to VCC keeps it recessive when unused, VIH is 2 V to VCC+0.3 V and VIL is -0.3 V to 0.8 V, and the dominant timeout (tdom 300 to 1000 µs) disables the transceiver if TXD is held low. |
| 2 | GND | power_in | Ground reference for the transceiver. |
| 3 | VCC | power_in | Supply voltage with a 4.75 V to 5.25 V operating range and an absolute maximum of -0.3 V to 6 V without time limit. |
| 4 | RXD | output | Receive data output that reads the bus state, high when the bus is recessive; it is floated when VCC is lost to prevent reverse current, and its high-level output is VCC-0.4 V minimum in normal mode at -0.4 mA. |
| 5 | SPLIT | power_out | Common-mode regulated output at 0.5 VCC (0.3 VCC to 0.7 VCC for -500 µA to 500 µA load) that is active only in normal mode and left floating in standby; connect it to the centre tap of a split termination. |
| 6 | CANL | bidirectional | Low-level CAN bus line with dominant output voltage of 0.5 V to 1.75 V (1.4 V typical) and bus pin voltage rated -27 V to 40 V. |
| 7 | CANH | bidirectional | High-level CAN bus line with dominant output voltage of 3 V to 4.25 V (3.6 V typical) and bus pin voltage rated -27 V to 40 V. |
| 8 | STB | input | Standby mode control input: low selects normal mode and high selects standby mode, with an internal pull-up to VCC, VIH of 2 V to VCC+0.3 V and VIL of -0.3 V to 0.8 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | MSOP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply current, standby mode | ICC | 5 | 10 | 15 | µA | 待机模式 | 5 |
| Supply current, normal mode recessive | ICC | 2.5 | 5 | 10 | mA | 正常模式：隐性 VTXD = VCC | 5 |
| Supply current, normal mode dominant | ICC | 30 | 50 | 70 | mA | 正常模式：显性 VTXD =0V | 5 |
| TXD high-level input current | IIH | -5 | 0 | 5 | µA | VTXD = VCC | 5 |
| TXD low-level input current | IIL | -300 | -200 | -100 | µA | 正常模式：VTXD = 0V | 5 |
| TXD input capacitance | GI | 5 | 10 | pF | 未测试 | 5 | |
| TXD low-level input voltage | VIL | -0.3 | 0.8 | V | 5 | ||
| STB low-level input current | IIL | -10 | -4 | -1 | µA | VSTB = 0V | 5 |
| STB low-level input voltage | VIL | -0.3 | 0.8 | V | 5 | ||
| RXD high-level output current, normal mode | IOH | -1 | -0.4 | -0.1 | mA | 正常模式： VRXD = VCC −0.4V | 5 |
| RXD low-level output current | IOL | 2 | 6 | 20 | mA | VRXD = 0.4V | 5 |
| SPLIT leakage current, standby mode | /IL/ | 0 | 5 | µA | 待机模式：−22V＜VSPLIT＜35V | 5 | |
| Dominant output voltage matching, CANH/CANL | VO(Dom)(m) | -100 | 0 | 150 | mV | 6 | |
| Differential bus output voltage, dominant | VO(dif)(bus) | 1.5 | 3 | V | VTXD = 0V；显性；45Ω＜RL＜65Ω | 6 | |
| Differential bus output voltage, recessive | VO(dif)(bus) | -50 | 50 | mV | VTXD = VCC；隐性；空载 | 6 | |
| CANL recessive output voltage, normal mode | V(CANL)(reces) | 2 | 3 | V | 正常模式：VTXD = VCC；无负载 | 6 | |
| CANL recessive output voltage, standby mode | V(CANL)(reces) | -0.1 | 0 | 0.1 | V | 待机模式；无负载 | 6 |
| CANH dominant output voltage | V(CANH)(dom) | 3 | 3.6 | 4.25 | V | VTXD = 0V | 5 |
| CANL dominant output voltage | V(CANL)(dom) | 0.5 | 1.4 | 1.75 | V | VTXD = 0V | 5 |
| CANH short-circuit output current | IO(CANH)(sc) | -95 | -70 | -40 | mA | VTXD = 0V； VCANH = 0V | 6 |
| CANL short-circuit output current | IO(CANL)(sc) | 40 | 70 | 100 | mA | VTXD = 0V； VCANL= 40V | 6 |
| CANL recessive output current | IO(CANL)(reces) | -2.5 | 2.5 | mA | −27V＜VCAN＜32V | 6 | |
| Differential receiver threshold voltage, normal mode | Vdif(th) | 0.5 | 0.7 | 0.9 | V | −12V＜VCANH＜12V；−12V＜VCANL＜12V；正常模式 | 6 |
| Differential receiver threshold voltage, standby mode | Vdif(th) | 0.5 | 0.7 | 1.15 | V | −12V＜VCANH＜12V；−12V＜VCANL＜12V；待机模式 | 6 |
| Differential receiver hysteresis voltage, normal mode | Vdif(hys) | 50 | 70 | 100 | mV | 正常模式 −12V＜VCANH＜12V；−12V＜VCANL＜12V | 6 |
| Input leakage current, CANH/CANL | ILI | -5 | 0 | 5 | µA | VCC = 0V；VCANH = VCANL= 5V | 6 |
| Common-mode input impedance | Ri(cm) | 15 | 25 | 35 | kΩ | 正常/待机模式 | 6 |
| Common-mode input impedance matching, CANH vs CANL | Ri(cm)(m) | -3 | 0 | 3 | % | VCANH = VCANL | 6 |
| Differential input impedance | Ri(dif) | 25 | 50 | 75 | kΩ | 正常/待机模式 | 6 |
| Common-mode input capacitance | Ci(cm) | 20 | pF | VTXD = VCC；未测试 | 6 | ||
| Differential input capacitance | Ci(dif) | 10 | pF | VTXD = VCC；未测试 | 6 | ||
| TXD to bus active delay | td(TXD-BUSon) | 25 | 70 | 110 | ns | 正常模式 | 6 |
| TXD to bus inactive delay | td(TXD-BUSoff) | 10 | 50 | 95 | ns | 6 | |
| Bus active to RXD delay | td(BUSon-RXD) | 15 | 65 | 115 | ns | 6 | |
| Bus inactive to RXD delay | td(BUSoff-RXD) | 35 | 100 | 160 | ns | 6 | |
| TXD to RXD propagation delay | tPD(TXD-RXD) | 40 | 255 | ns | VSTB = 0V | 7 | |
| TXD dominant timeout | tdom(TXD) | 300 | 600 | 1000 | µs | VTXD = 0V | 7 |
| Wake-up dominant time on bus | tBUS | 0.75 | 1.75 | 5 | µs | 待机模式 | 7 |
| Standby to normal mode delay | td(stb-norm) | 5 | 7.5 | 10 | µs | 正常模式 | 7 |
| Thermal shutdown junction temperature | Tj(sd) | 155 | 165 | 180 | ℃ | 7 | |
| Supply voltage VCC, no time limit | VCC | -0.3 | 6 | V | 无时间限制 | 4 | |
| Supply voltage VCC, operating range | VCC | 4.75 | 5.25 | V | 工作范围 | 4 | |
| DC voltage on TXD pin | VTXD | -0.3 | V | max printed as VCC+0.3 | 4 | ||
| DC voltage on RXD pin | VRXD | -0.3 | V | max printed as VCC+0.3 | 4 | ||
| DC voltage on STB pin | VSTB | -0.3 | V | max printed as VCC+0.3 | 4 | ||
| DC voltage on CANH pin | VCANH | -27 | 40 | V | 0 < VCC < 5.25 V，无时间限制 | 4 | |
| DC voltage on CANL pin | VCANL | -27 | 40 | V | 0 < VCC < 5.25 V，无时间限制 | 4 | |
| DC voltage on SPLIT pin | VSPLIT | -27 | 40 | V | 0 < VCC < 5.25 V，无时间限制 | 4 | |
| Transient voltage on CANL, CANH and SPLIT pins | VTRT | -200 | 200 | V | 根据 ISO7637 | 4 | |
| ESD voltage, human body model, CANL/CANH/SPLIT pins | VESD | -6 | 6 | kV | 人体模型；引脚 CANL、CANH、SPLIT，注意 1 | 4 | |
| ESD voltage, human body model, other pins | VESD | -4 | 4 | kV | 人体模型；其他引脚 | 4 | |
| ESD voltage, machine model | VESD | -200 | 200 | V | 机器模型，注意 2 | 4 | |
| Actual junction temperature | TVJ | -40 | 150 | ℃ | 注意 3 | 4 | |
| Storage temperature | TSTG | -55 | 150 | ℃ | 4 | ||
| Lead temperature, soldering 10 s | TLEAD | 245 | ℃ | 焊接10s | 4 |
CAD (KiCad official)
- Symbol:
PCA82C250MM - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
pca82c250mm-etched.step/pca82c250mm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pca82c250mm.step/pca82c250mm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet (11 pp, sha256
294e8cbe2fa18ee6, retrieved 2026-10-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).