main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers pac1952t-2e: viewers · Ray
pac1952t-2e-etched.glb Publish 0.1.0 · Ray
pac1952t-2e-etched.step pac1952t-2e: factory component page (tier=mfr) · Ray
pac1952t-2e-hero.glb pac1952t-2e: hero GLB from the etched model (keeps the MPN mark) · Ray
pac1952t-2e-hero.overlay.json Publish 0.1.0 · Ray
pac1952t-2e.glb Publish 0.1.0 · Ray
pac1952t-2e.kicad_mod Publish 0.1.0 · Ray
pac1952t-2e.kicad_sym Publish 0.1.0 · Ray
pac1952t-2e.lbr Publish 0.1.0 · Ray
pac1952t-2e.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 17 pins · Ray

PAC1952T-2E

Microchip Tech · Monitors & Reset Circuits · VQFN-16(3x3)

PAC1952T-2E from Microchip Tech, in a VQFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SLOW/ALERT1 bidirectional Digital I/O pin that defaults to a SLOW input: when high, all channels sample at 8 SPS, and it may be programmed as the open-drain ALERT1 pin or as a GPIO.
2 VDD power_in Positive power supply input for the device, 2.7V to 5.5V, to be bypassed with a 100 nF ceramic capacitor to ground near the IC.
3 GND power_in System ground for the IC.
4 SCL input SMBus clock input that requires an external pull-up resistor (a CMOS driver from the host is required in High-Speed mode).
5 SDA bidirectional Bidirectional SMBus open-drain data pin that requires a pull-up resistor to VDD.
6 ADDRSEL bidirectional Address selection pin; connect a resistor from this pin to ground to select the SMBus client address.
7 VBUS2- input Analog input, 0 to FSR (safe operating voltage up to 32V), to be connected to the ground sense point for VBUS2.
8 VBUS2+ input Analog input, 0 to FSR (safe operating voltage up to 32V), to be connected to VBUS2+.
9 SENSE2- input Analog input, 0 to FSR (safe operating voltage up to 32V; common-mode range 0V to 32V for PAC195X-2), to be connected to the low side of the sense resistor as printed in the datasheet.
10 SENSE2+ input Analog input, 0 to FSR (safe operating voltage up to 32V; common-mode range 0V to 32V for PAC195X-2), to be connected to the low side of the sense resistor as printed in the datasheet.
11 SENSE1+ input Analog input, 0 to FSR (safe operating voltage up to 32V; common-mode range 0V to 32V for PAC195X-2), to be connected to the low side of the sense resistor as printed in the datasheet.
12 SENSE1- input Analog input, 0 to FSR (safe operating voltage up to 32V; common-mode range 0V to 32V for PAC195X-2), to be connected to the low side of the sense resistor as printed in the datasheet.
13 VBUS1+ input Analog input, 0 to FSR (safe operating voltage up to 32V), to be connected to VBUS1+.
14 VBUS1- input Analog input, 0 to FSR (safe operating voltage up to 32V), to be connected to the ground sense point for VBUS1.
15 GPIO/ALERT2 bidirectional Digital I/O pin that defaults to GPIO input mode and may be programmed as the open-drain ALERT2 indicator or as an open-drain GPIO output; it requires a pull-up resistor to VDD when used as an output or ALERT.
16 PWRDN input Active-low power-down input that puts the device into a Power-Down state in which all circuitry, including SMBus, is powered down.
17 EP unconnected Exposed thermal pad, not electrically connected inside the device; the datasheet recommends connecting it to ground.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package VQFN-16(3x3)
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDD Range VDD 2.7 5.5 V 6
VDD Active Current IDD 395 495 µA 1024 SPS, 4 channels enabled 6
VDD Active Current IDD 395 440 µA 1024 SPS, 4 channels enabled TA = 0°C to +85°C 6
VDD Active Current IDD 12 25 µA 8 SPS, 4 channels enabled TA = 0°C to +85°C 6
VDD Power-Down Current IDD_PWRDN 0 8 µA 6
Bus Voltage Range VBUS -0.2 32 V Common-mode voltage on SENSE pins, referenced to ground 6
VSENSE Differential Input Voltage Range VSENSE_DIF -100 100 mV 6
SENSE+, SENSE- Pin Input Current ISENSE+, ISENSE- -6 0.6 6 µA VSENSE+ = VSENSE- = Full scale 6
SENSE+, SENSE- Pin Input Current ISENSE+, ISENSE- -1 0.4 1 µA VSENSE+ = 6V, VSENSE- = 5.9V 6
VSENSE ADC Data Resolution VSENSE_RES 16 Bits 6
VBUS ADC Data Resolution VBUS_RES 16 Bits 14 bits are used for power calculations, 16 bits are reported when the VBUS measurement result is read 6
VSENSE Gain Accuracy VSENSE_GAIN_ERR -0.5 0.5 % At +25°C typical, -40°C to +125°C 7
VBUS Gain Accuracy VBUS_GAIN_ERR -0.25 0.25 % At +25°C typical, -40°C to +125°C 7
VSENSE Offset Accuracy, Referenced to Input VSENSE_OFFSET_ERR -100 25 100 µV 16-bit resolution 7
Time to First Communications tINT_T 50 ms Time after VDD is applied before it is ready to begin communication and measurement. 7
Transition from Sleep State to Start of Conversion Cycle tSLEEP_TO_ACTIVE 5 ms Time from Sleep state exit commanded by register write to the beginning of the conversion cycle. 7
Input High Voltage (SLOW/ALERT, SM_CLK, SM_DATA) VIH 1.35 V 7
Input Low Voltage (SLOW/ALERT, SM_CLK, SM_DATA) VIL 0.8 V 7
Output Low Voltage (SLOW/ALERT, SM_CLK, SM_DATA) VOL 0.4 V Sinking 8 mA for the ALERT pins and 20 mA for the CLK pin in all modes. 4 mA for the SDA pin in 3.4 MHz mode. 7
Leakage Current (SLOW/ALERT, SM_CLK, SM_DATA) ILEAK -0.5 0.5 µA Powered or unpowered 7
Input High Voltage (PWRDN) VIH 1.3 V 7
Input Low Voltage (PWRDN) VIL 0.6 V 7
Clock Frequency (Fast Mode Plus) fSMB 0.01 1 MHz Fast Mode Plus. No minimum if Time-out is not enabled. 8
Clock Frequency (High-Speed mode) fSMB 0.01 3.4 MHz High-Speed mode. No minimum if Time-out is not enabled. 8
Spike Suppression (Fast Mode Plus) tSP 0 50 ns Fast Mode Plus 8
Spike Suppression (High-Speed mode) tSP 0 10 ns High-Speed mode 8
Bus Free Time Stop to Start tBUF 0.5 µs Per SMBus 3.1 8
Hold Time after Repeated Start Condition (Fast Mode Plus) tHD:STA 0.26 µs Per SMBus 3.1, Fast Mode Plus 8
Hold Time after Repeated Start Condition (High-Speed mode) tHD:STA 0.16 µs Per SMBus 3.1, High-Speed mode 8
Repeated Start Condition Setup Time (Fast Mode Plus) tSU:STA 0.26 µs Per SMBus 3.1, Fast Mode Plus 8
Repeated Start Condition Setup Time (High-Speed mode) tSU:STA 0.16 µs Per SMBus 3.1, High-Speed mode 8
Setup Time: Stop (Fast Mode Plus) tSU:STO 0.26 µs Per SMBus 3.1, Fast Mode Plus 8
Setup Time: Stop (High-Speed mode) tSU:STO 0.16 µs Per SMBus 3.1, High-Speed mode 8
Data Hold Time (Fast Mode Plus) tHD:DAT 0 ns Per SMBus 3.1, Fast Mode Plus 8
Data Hold Time (High-Speed mode) tHD:DAT 0 70 ns Per SMBus 3.1, High-Speed mode 8
Data Setup Time (Fast Mode Plus) tSU:DAT 50 ns Per SMBus 3.1, Fast Mode Plus 8
Data Setup Time (High-Speed mode) tSU:DAT 10 ns Per SMBus 3.1, High-Speed mode 8
Clock Low Period (Fast Mode Plus) tLOW 0.5 µs Per SMBus 3.1, Fast Mode Plus 8
Clock Low Period (High-Speed mode) tLOW 0.16 µs Per SMBus 3.1, High-Speed mode 8
Clock High Period (Fast Mode Plus) tHIGH 0.26 50 µs Fast Mode Plus 8
Clock High Period (High-Speed mode) tHIGH 0.06 50 µs High-Speed mode 8
Clock/Data Fall Time (Fast Mode Plus) tFALL 12 120 ns Fast Mode Plus 8
Clock/Data Rise Time (Fast Mode Plus) tRISE 120 ns Fast Mode Plus 8
Clock Fall Time (High-Speed mode) tfCL 10 40 ns High-Speed mode 8
Clock Rise Time (High-Speed mode) trCL 10 40 ns High-Speed mode 8
Data Fall Time (High-Speed mode) tfDA 10 80 ns High-Speed mode 8
Data Rise Time (High-Speed mode) trDA 10 80 ns High-Speed mode 8
Capacitive Load (Fast Mode Plus) CLOAD 550 pF Per bus line, Fast Mode Plus 9
Capacitive Load (High-Speed mode) CLOAD 100 pF Per bus line, High-Speed mode 9
SLOW Pin Pulse Width SLOWpw 150 µs Pulses narrower than 150 µS may not be detected 9
Operating Temperature Range TA -40 125 °C 9
Storage Temperature Range TSTG -55 150 °C 9
VDD Pin VDD -0.3 6 V 5
Voltage on SENSE- and SENSE+ Pins -0.3 40 V 5
Voltage on Any Other Pin to GND -0.3 6 V 5
Input Current to Any Pin Except VDD -100 100 mA 5
Thermal Resistance, 16-Lead VQFN (junction-to-ambient) JA 39.9 °C/W 9
Thermal Resistance, 16-Lead VQFN (junction-to-case) JC 23.1 °C/W 9

CAD (KiCad official)

  • Symbol: PAC1952T-2E
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: VQFN-16(3x3) (KiCad packages3D, STEP)
  • 3D model files: pac1952t-2e-etched.step / pac1952t-2e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pac1952t-2e.step / pac1952t-2e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (96 pp, sha256 52bb78abaa920f4f, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF