Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

PAC1951T-1E

MICROCHIP TECHNOLOGY · Global Sourcing Parts · VQFN-16(3x3)

PAC1951T-1E from MICROCHIP TECHNOLOGY, in a VQFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SLOW/ALERT1 bidirectional Default SLOW input: when high, all channels sample at 8 SPS; it may be programmed as the ALERT1 pin (open-drain, needs a pull-up resistor to VDD) or as a GPIO (default input, configurable as open-drain output).
2 VDD power_in Positive power supply input, 2.7V to 5.5V; bypass with a 100 nF ceramic capacitor to ground near the IC.
3 GND power_in Ground for the IC (system ground).
4 SCL input SMBus/I2C clock input; requires an external pull-up resistor, except in High-Speed mode, which requires a CMOS driver from the host.
5 SDA bidirectional SMBus/I2C bidirectional data pin; open-drain, requires a pull-up resistor to VDD.
6 ADDRSEL passive Address selection: connect a single resistor from this pin to ground to set the SMBus client address per Table 6-1.
7 SENSE3- passive For PAC1951-1 this pin is not connected internally and must be grounded.
8 SENSE3+ passive For PAC1951-1 this pin is not connected internally and must be grounded.
9 SENSE4- passive For PAC1951-1 this pin is not connected internally and must be grounded.
10 SENSE4+ passive For PAC1951-1 this pin is not connected internally and must be grounded.
11 SENSE1+ input Analog input, 0-FSR, connect to the supply side of the sense resistor; it also serves as the bus voltage (VBUS) input, with a safe operating voltage up to 32V.
12 SENSE1- input Analog input, 0-FSR, connect to the load side of the sense resistor; safe operating voltage up to 32V.
13 SENSE2+ passive For PAC1951-1 this pin is not connected internally and must be grounded.
14 SENSE2- passive For PAC1951-1 this pin is not connected internally and must be grounded.
15 GPIO/ALERT2 bidirectional Default GPIO input; may be programmed as the ALERT2 pin or as a GPIO output, both open-drain, requiring a pull-up resistor to VDD.
16 PWRDN input Active-low power-down input; when pulled low, all circuitry including the SMBus is powered down.
17 EP unconnected Exposed thermal pad is not electrically connected inside the device; it is recommended to connect it to ground.

Key specifications

Parameter Value
Manufacturer MICROCHIP TECHNOLOGY
Package VQFN-16(3x3)
Category Global Sourcing Parts
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDD Pin (absolute maximum) -0.3 6 V 5
Voltage on SENSE- and SENSE+ Pins (absolute maximum) -0.3 40 V 5
Voltage on Any Other Pin to GND (absolute maximum) -0.3 6 V 5
Input Current to Any Pin Except VDD (absolute maximum) -100 100 mA 5
Operating Ambient Temperature Range (absolute maximum) -40 150 °C 5
Storage Temperature Range (absolute maximum) -55 150 °C 5
VDD Range VDD 2.7 5.5 V 6
VDD Active Current IDD 395 495 µA 1024 SPS, 4 channels enabled 6
VDD Active Current, TA = 0°C to +85°C IDD 395 440 µA 1024 SPS, 4 channels enabled, TA = 0°C to +85°C 6
VDD Active Current, 8 SPS IDD 12 25 µA 8 SPS, 4 channels enabled, TA = 0°C to +85°C 6
VDD Power-Down Current IDD_PWRDN 0 8 µA 6
Bus Voltage Range VBUS -0.2 32 V Common-mode voltage on SENSE pins, referenced to ground 6
VSENSE Differential Input Voltage Range VSENSE_DIF -100 100 mV 6
SENSE+, SENSE- Pin Input Current ISENSE+, ISENSE- -6 0.6 6 µA VSENSE+ = VSENSE- = Full scale; includes leakage and average capacitively coupled switching current 6
SENSE+, SENSE- Pin Input Current ISENSE+, ISENSE- -1 0.4 1 µA VSENSE+ = 6V, VSENSE- = 5.9V; includes leakage and average capacitively coupled switching current 6
VSENSE ADC Data Resolution VSENSE_RES 16 Bits 6
VBUS ADC Data Resolution VBUS_RES 16 Bits 14 bits used for power calculations, 16 bits reported when the VBUS measurement result is read 6
VSENSE Gain Accuracy VSENSE_GAIN_ERR -0.5 0.5 % At +25°C typical, -40°C to +125°C 7
VSENSE Offset Accuracy, Referenced to Input VSENSE_OFFSET_ERR -100 25 100 µV 16-bit resolution 7
VBUS Gain Accuracy VBUS_GAIN_ERR -0.25 0.25 % At +25°C typical, -40°C to +125°C 7
Time to First Communications tINT_T 50 ms Time after VDD is applied before it is ready to begin communication and measurement 7
Transition from Sleep State to Start of Conversion Cycle tSLEEP_TO_ACTIVE 5 ms Time from Sleep state exit commanded by register write to the beginning of the conversion cycle 7
Digital I/O Input High Voltage (SLOW/ALERT, SM_CLK, SM_DATA) VIH 1.35 V 7
Digital I/O Input Low Voltage (SLOW/ALERT, SM_CLK, SM_DATA) VIL 0.8 V 7
Digital I/O Output Low Voltage (SLOW/ALERT, SM_CLK, SM_DATA) VOL 0.4 V Sinking 8 mA for ALERT pins and 20 mA for CLK pin in all modes; 4 mA for SDA pin in 3.4 MHz mode 7
Digital I/O Leakage Current ILEAK -0.5 0.5 µA Powered or unpowered 7
PWRDN Input High Voltage VIH 1.3 V 7
PWRDN Input Low Voltage VIL 0.6 V 7
Specified Temperature Range TA -40 125 °C 9
Operating Temperature Range TA -40 125 °C 9
Storage Temperature Range TSTG -55 150 °C 9
Clock Frequency, Fast Mode Plus fSMB 0.01 1 MHz Fast Mode Plus. No minimum if Time-out is not enabled 8
Clock Frequency, High-Speed mode fSMB 0.01 3.4 MHz High-Speed mode. No minimum if Time-out is not enabled 8
Spike Suppression, Fast Mode Plus tSP 0 50 ns Fast Mode Plus 8
Spike Suppression, High-Speed mode tSP 0 10 ns High-Speed mode 8
Bus Free Time Stop to Start tBUF 0.5 µs Per SMBus 3.1 8
Hold Time after Repeated Start Condition, Fast Mode Plus tHD:STA 0.26 µs Per SMBus 3.1, Fast Mode Plus 8
Hold Time after Repeated Start Condition, High-Speed mode tHD:STA 0.16 µs Per SMBus 3.1, High-Speed mode 8
Repeated Start Condition Setup Time, Fast Mode Plus tSU:STA 0.26 µs Per SMBus 3.1, Fast Mode Plus 8
Repeated Start Condition Setup Time, High-Speed mode tSU:STA 0.16 µs Per SMBus 3.1, High-Speed mode 8
Setup Time: Stop, Fast Mode Plus tSU:STO 0.26 µs Per SMBus 3.1, Fast Mode Plus 8
Setup Time: Stop, High-Speed mode tSU:STO 0.16 µs Per SMBus 3.1, High-Speed mode 8
Data Hold Time, Fast Mode Plus tHD:DAT 0 ns Per SMBus 3.1, Fast Mode Plus 8
Data Hold Time, High-Speed mode tHD:DAT 0 70 ns Per SMBus 3.1, High-Speed mode 8
Data Setup Time, Fast Mode Plus tSU:DAT 50 ns Per SMBus 3.1, Fast Mode Plus 8
Data Setup Time, High-Speed mode tSU:DAT 10 ns Per SMBus 3.1, High-Speed mode 8
Clock Low Period, Fast Mode Plus tLOW 0.5 µs Per SMBus 3.1, Fast Mode Plus 8
Clock Low Period, High-Speed mode tLOW 0.16 µs Per SMBus 3.1, High-Speed mode 8
Clock High Period, Fast Mode Plus tHIGH 0.26 50 µs Fast Mode Plus 8
Clock High Period, High-Speed mode tHIGH 0.06 50 µs High-Speed mode 8
Clock/Data Fall Time, Fast Mode Plus tFALL 12 120 ns Fast Mode Plus 8
Clock/Data Rise Time, Fast Mode Plus tRISE 120 ns Fast Mode Plus 8
Clock Fall Time, High-Speed mode tfCL 10 40 ns High-Speed mode 8
Clock Rise Time, High-Speed mode trCL 10 40 ns High-Speed mode 8
Capacitive Load, Fast Mode Plus CLOAD 550 pF Per bus line, Fast Mode Plus 9
Capacitive Load, High-Speed mode CLOAD 100 pF Per bus line, High-Speed mode 9
SLOW Pin Pulse Width SLOWpw 150 µs Pulses narrower than 150 µs may not be detected 9
Thermal Resistance, 16-Lead VQFN, Junction-to-Ambient θJA 39.9 °C/W 9
Thermal Resistance, 16-Lead VQFN, Junction-to-Case θJC 23.1 °C/W 9

CAD (KiCad official)

  • Symbol: PAC1951T-1E
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: VQFN-16(3x3) (KiCad packages3D, STEP)
  • 3D model files: pac1951t-1e-4mx-etched.step / pac1951t-1e-4mx-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); pac1951t-1e-4mx.step / pac1951t-1e-4mx.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: MICROCHIP TECHNOLOGY datasheet (96 pp, sha256 52bb78abaa920f4f, retrieved 2026-11-11, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF