component
P24C128D-SSH-MIR
Public Made by Adomby adom
PUYA EEPROM, SOP-8. Pinout extracted from the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownP24C128D-SSH-MIR
PUYA · EEPROM · SOP-8
P24C128D-SSH-MIR from PUYA, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | E0 | input | Device slave-address setting bit 0. Hardwire to VCC or GND to set A0 of the 7-bit I2C slave address (allows up to 8 devices on one bus). If left floating, an internal pull-down forces this bit to 0. |
| 2 | E1 | input | Device slave-address setting bit 1. Hardwire to VCC or GND to set A1 of the 7-bit I2C slave address. If left floating, an internal pull-down forces this bit to 0. |
| 3 | E2 | input | Device slave-address setting bit 2. Hardwire to VCC or GND to set A2 of the 7-bit I2C slave address. If left floating, an internal pull-down forces this bit to 0. |
| 4 | GND | power_in | Ground reference for the device (0 V). |
| 5 | SDA | bidirectional | I2C serial data input/output. Open-drain, requires an external pull-up to VCC; can be wire-OR'd with other open-drain devices. Schmitt-triggered noise-suppressed input; output VOL <= 0.2 V at IOL = 1.5 mA (VCC = 1.7 V). |
| 6 | SCL | input | I2C serial clock input. Data is clocked in on the rising edge and clocked out on the falling edge. Supports up to 400 kHz below VCC = 2.5 V and up to 1 MHz from 2.5 V to 5.5 V. |
| 7 | WCB | input | Write control (active-low enable). Tie to GND to allow normal writes; tie to VCC to inhibit all writes to the memory array. Internally pulled down (5 M-ohm typ., 30 k-ohm max) so a floating pin defaults to write-enabled. |
| 8 | VCC | power_in | Supply voltage input. -MI grade: 1.7 V to 5.5 V, -40 C to +85 C. Standby current <= 1.0 uA (VCC = 3.3 V, 85 C); read current <= 400 uA; write current <= 1.6 mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | PUYA |
| Package | SOP-8 |
| Category | Memory |
| Pins | 8 |
Ordering variants
Same part, different packaging or reel option.
P24C128D-SSH-MIR
CAD (KiCad official)
- Symbol:
P24C128D-SSH-MIR - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: PUYA datasheet (25 pp, sha256
4e7c982781c7caea, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).