main
Ray
opa322saidbvr: specified limits as data (metadata.characteristics, 36 rows from the datasheet)
694ba04
OPA322SAIDBVR
Texas Instruments · Operational Amplifier · SOT-23-6
OPA322SAIDBVR from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V+ | power_in | Positive supply pin; specified operating supply range is 1.8 V to 5.5 V (or ±0.9 V to ±2.75 V split supply), absolute maximum (V+)-(V-) supply voltage is 6 V; a local 0.001 µF to 0.1 µF ceramic bypass capacitor is recommended. |
| 2 | SHDN | input | Active-high shutdown/enable input referenced to V-; a logic high of (V+)-0.1 V up to V+ enables the amplifier while a logic low of (V-)+0.1 V down to V- disables it, with 5.5 V max allowed relative to V-; the pin must be driven to a valid level and not left floating, and disabled channels draw a typical 0.1 µA (max 0.5 µA) quiescent current. |
| 3 | -IN | input | Inverting input of the operational amplifier; common-mode input voltage range is (V-)-0.1 V to (V+)+0.1 V, and input current should be limited to 10 mA or less (via series resistor) for signals overdriving the supply rails by more than 0.5 V. |
| 4 | +IN | input | Non-inverting input of the operational amplifier; common-mode input voltage range is (V-)-0.1 V to (V+)+0.1 V, and input current should be limited to 10 mA or less for overdrive protection. |
| 5 | V- | power_in | Negative supply pin (ground reference in single-supply operation); together with V+ establishes the 1.8 V to 5.5 V (or ±0.9 V to ±2.75 V) supply range and should have a local ceramic bypass capacitor. |
| 6 | OUT | output | Amplifier output; rail-to-rail output typically swings within 10 mV (20 mV max) of either supply rail into a 10-kΩ load, delivers up to ±65 mA short-circuit current at VS=5.5 V, and enters a high-impedance state when the device is disabled via SHDN. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-23-6 |
| Category | Amplifiers/Comparators |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage, VS = (V+) – (V–) | VS | 6 | V | 2 | |||
| Signal input pins current | -10 | 10 | mA | 2 | |||
| Operating temperature | TA | -40 | 150 | °C | Over operating free-air temperature range | 2 | |
| Storage temperature | Tstg | -65 | 150 | °C | 2 | ||
| Junction temperature | TJ | 150 | °C | 2 | |||
| ESD Human body model (HBM) | 4000 | V | 2 | ||||
| ESD Charged device model (CDM) | 1000 | V | 2 | ||||
| ESD Machine model (MM) | 200 | V | 2 | ||||
| Specified voltage range | VS | 1.8 | 5.5 | V | 4 | ||
| Specified temperature range | -40 | 125 | °C | 4 | |||
| Operating range | -40 | 150 | °C | 4 | |||
| Input offset voltage | VOS | 0.5 | 2 | mV | 3 | ||
| Input offset voltage vs temperature | dVOS/dT | 1.8 | 6 | μV/°C | VS = +5.5 V | 3 | |
| Power supply rejection | PSR | 10 | 50 | μV/V | VS = +1.8 V to +5.5 V | 3 | |
| Power supply rejection over temperature | PSR | 20 | 65 | μV/V | Over temperature; VS = +1.8 V to +5.5 V | 3 | |
| Common-mode rejection ratio | CMRR | 90 | 100 | dB | (V–) – 0.1 V < VCM < (V+) + 0.1 V | 3 | |
| Common-mode rejection ratio over temperature | CMRR | 90 | dB | Over temperature | 3 | ||
| Input bias current | IB | -10 | 0.2 | 10 | pA | 3 | |
| Input bias current | IB | -50 | 50 | pA | TA = –40°C to +85°C | 3 | |
| Input bias current over temperature (OPA322, OPA322S) | IB | -800 | 800 | pA | Over temperature; TA = –40°C to +125°C | 3 | |
| Input offset current | IOS | -10 | 0.2 | 10 | pA | 3 | |
| Input offset current | IOS | -50 | 50 | pA | TA = –40°C to +85°C | 3 | |
| Input offset current over temperature | IOS | -400 | 400 | pA | TA = –40°C to +125°C | 3 | |
| Open-loop voltage gain | AOL | 100 | 130 | dB | 0.1 V < VO < (V+) – 0.1 V, RL = 10 kΩ | 3 | |
| Open-loop voltage gain (second row) | AOL | 94 | dB | 0.1 V < VO < (V+) – 0.1 V, RL = 10 kΩ | 3 | ||
| Voltage output swing from rails | VO | 10 | 20 | mV | RL = 10 kΩ, both rails | 4 | |
| Voltage output swing from rails over temperature | VO | 30 | mV | Over temperature; RL = 10 kΩ | 4 | ||
| Short-circuit current | ISC | -65 | 65 | mA | VS = 5.5 V | 4 | |
| Quiescent current per amplifier | IQ | 1.6 | 1.9 | mA | IO = 0 mA, VS = +5.5 V | 4 | |
| Quiescent current per amplifier over temperature | IQ | 2 | mA | Over temperature; IO = 0 mA, VS = +5.5 V | 4 | ||
| Quiescent current per amplifier in shutdown | IQSD | 0.1 | 0.5 | µA | All amplifiers disabled, SHDN = VS– | 4 | |
| Junction-to-ambient thermal resistance | θJA | 177.5 | °C/W | OPA322S DBV 6-pin package | 5 | ||
| Junction-to-case(top) thermal resistance | θJC(top) | 108.9 | °C/W | OPA322S DBV 6-pin package | 5 | ||
| Junction-to-board thermal resistance | θJB | 27.4 | °C/W | OPA322S DBV 6-pin package | 5 | ||
| Junction-to-top characterization parameter | ψJT | 13.3 | °C/W | OPA322S DBV 6-pin package | 5 | ||
| Junction-to-board characterization parameter | ψJB | 26.9 | °C/W | OPA322S DBV 6-pin package | 5 |
CAD (KiCad official)
- Symbol:
OPA322SAIDBVR - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
opa322saidbvr-etched.step/opa322saidbvr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);opa322saidbvr.step/opa322saidbvr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (51 pp, sha256
b4b7c5ce416fcd4d, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# OPA322SAIDBVR
**Texas Instruments** · Operational Amplifier · SOT-23-6
OPA322SAIDBVR from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V+ | power_in | Positive supply pin; specified operating supply range is 1.8 V to 5.5 V (or ±0.9 V to ±2.75 V split supply), absolute maximum (V+)-(V-) supply voltage is 6 V; a local 0.001 µF to 0.1 µF ceramic bypass capacitor is recommended. |
| 2 | SHDN | input | Active-high shutdown/enable input referenced to V-; a logic high of (V+)-0.1 V up to V+ enables the amplifier while a logic low of (V-)+0.1 V down to V- disables it, with 5.5 V max allowed relative to V-; the pin must be driven to a valid level and not left floating, and disabled channels draw a typical 0.1 µA (max 0.5 µA) quiescent current. |
| 3 | -IN | input | Inverting input of the operational amplifier; common-mode input voltage range is (V-)-0.1 V to (V+)+0.1 V, and input current should be limited to 10 mA or less (via series resistor) for signals overdriving the supply rails by more than 0.5 V. |
| 4 | +IN | input | Non-inverting input of the operational amplifier; common-mode input voltage range is (V-)-0.1 V to (V+)+0.1 V, and input current should be limited to 10 mA or less for overdrive protection. |
| 5 | V- | power_in | Negative supply pin (ground reference in single-supply operation); together with V+ establishes the 1.8 V to 5.5 V (or ±0.9 V to ±2.75 V) supply range and should have a local ceramic bypass capacitor. |
| 6 | OUT | output | Amplifier output; rail-to-rail output typically swings within 10 mV (20 mV max) of either supply rail into a 10-kΩ load, delivers up to ±65 mA short-circuit current at VS=5.5 V, and enters a high-impedance state when the device is disabled via SHDN. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-23-6 |
| Category | Amplifiers/Comparators |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage, VS = (V+) – (V–) | VS | | | 6 | V | | 2 |
| Signal input pins current | | -10 | | 10 | mA | | 2 |
| Operating temperature | TA | -40 | | 150 | °C | Over operating free-air temperature range | 2 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 2 |
| Junction temperature | TJ | | | 150 | °C | | 2 |
| ESD Human body model (HBM) | | | | 4000 | V | | 2 |
| ESD Charged device model (CDM) | | | | 1000 | V | | 2 |
| ESD Machine model (MM) | | | | 200 | V | | 2 |
| Specified voltage range | VS | 1.8 | | 5.5 | V | | 4 |
| Specified temperature range | | -40 | | 125 | °C | | 4 |
| Operating range | | -40 | | 150 | °C | | 4 |
| Input offset voltage | VOS | | 0.5 | 2 | mV | | 3 |
| Input offset voltage vs temperature | dVOS/dT | | 1.8 | 6 | μV/°C | VS = +5.5 V | 3 |
| Power supply rejection | PSR | | 10 | 50 | μV/V | VS = +1.8 V to +5.5 V | 3 |
| Power supply rejection over temperature | PSR | | 20 | 65 | μV/V | Over temperature; VS = +1.8 V to +5.5 V | 3 |
| Common-mode rejection ratio | CMRR | 90 | 100 | | dB | (V–) – 0.1 V < VCM < (V+) + 0.1 V | 3 |
| Common-mode rejection ratio over temperature | CMRR | 90 | | | dB | Over temperature | 3 |
| Input bias current | IB | -10 | 0.2 | 10 | pA | | 3 |
| Input bias current | IB | -50 | | 50 | pA | TA = –40°C to +85°C | 3 |
| Input bias current over temperature (OPA322, OPA322S) | IB | -800 | | 800 | pA | Over temperature; TA = –40°C to +125°C | 3 |
| Input offset current | IOS | -10 | 0.2 | 10 | pA | | 3 |
| Input offset current | IOS | -50 | | 50 | pA | TA = –40°C to +85°C | 3 |
| Input offset current over temperature | IOS | -400 | | 400 | pA | TA = –40°C to +125°C | 3 |
| Open-loop voltage gain | AOL | 100 | 130 | | dB | 0.1 V < VO < (V+) – 0.1 V, RL = 10 kΩ | 3 |
| Open-loop voltage gain (second row) | AOL | 94 | | | dB | 0.1 V < VO < (V+) – 0.1 V, RL = 10 kΩ | 3 |
| Voltage output swing from rails | VO | | 10 | 20 | mV | RL = 10 kΩ, both rails | 4 |
| Voltage output swing from rails over temperature | VO | | | 30 | mV | Over temperature; RL = 10 kΩ | 4 |
| Short-circuit current | ISC | -65 | | 65 | mA | VS = 5.5 V | 4 |
| Quiescent current per amplifier | IQ | | 1.6 | 1.9 | mA | IO = 0 mA, VS = +5.5 V | 4 |
| Quiescent current per amplifier over temperature | IQ | | | 2 | mA | Over temperature; IO = 0 mA, VS = +5.5 V | 4 |
| Quiescent current per amplifier in shutdown | IQSD | | 0.1 | 0.5 | µA | All amplifiers disabled, SHDN = VS– | 4 |
| Junction-to-ambient thermal resistance | θJA | | 177.5 | | °C/W | OPA322S DBV 6-pin package | 5 |
| Junction-to-case(top) thermal resistance | θJC(top) | | 108.9 | | °C/W | OPA322S DBV 6-pin package | 5 |
| Junction-to-board thermal resistance | θJB | | 27.4 | | °C/W | OPA322S DBV 6-pin package | 5 |
| Junction-to-top characterization parameter | ψJT | | 13.3 | | °C/W | OPA322S DBV 6-pin package | 5 |
| Junction-to-board characterization parameter | ψJB | | 26.9 | | °C/W | OPA322S DBV 6-pin package | 5 |
## CAD (KiCad official)
- Symbol: `OPA322SAIDBVR`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files: `opa322saidbvr-etched.step` / `opa322saidbvr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `opa322saidbvr.step` / `opa322saidbvr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/opa2322) (51 pp, sha256 `b4b7c5ce416fcd4d`, retrieved 2026-09-23, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/opa322saidbvr-datasheet.pdf)