0914b0a
OPA2365AIDR
Texas Instruments · Operational Amplifier · SOIC-8
OPA2365AIDR from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol and footprint from KiCad-official CAD; the 3D model comes from KiCad's own package generator at the datasheet's values and carries TI's real Device Marking.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT A | output | Output of channel A. Rail-to-rail output stage; can swing to within millivolts of the supply rails under light load. |
| 2 | -IN A | input | Inverting input of channel A. Rail-to-rail input common-mode range (V- to V+). |
| 3 | +IN A | input | Non-inverting input of channel A. Rail-to-rail input common-mode range (V- to V+). |
| 4 | V- | power_in | Negative supply rail (or ground in single-supply operation). Total supply (V+ minus V-) range: 2.2 V to 5.5 V. |
| 5 | +IN B | input | Non-inverting input of channel B. Rail-to-rail input common-mode range (V- to V+). |
| 6 | -IN B | input | Inverting input of channel B. Rail-to-rail input common-mode range (V- to V+). |
| 7 | OUT B | output | Output of channel B. Rail-to-rail output stage; can swing to within millivolts of the supply rails under light load. |
| 8 | V+ | power_in | Positive supply rail. Total supply (V+ minus V-) range: 2.2 V to 5.5 V. Bypass with a 0.1 µF capacitor to V-/GND close to the pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | Op-amp/Cmp |
| Pins | 8 |
Ordering variants
Same part, different packaging or reel option.
OPA2365AIDROPA2365AIDRIDGKROPA2365AIDRIDGK
CAD
- Symbol:
OPA2365AIDR(KiCad, adom-symbol 1.2.6, chip outline baked in the body) - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm(KiCad official) - Fusion / EAGLE: opa2365aidr.lbr
Top marking (the real one, from the datasheet)
Every 3D file on this page that carries a marking carries the manufacturer's own top marking, not an invented label:
| Marking | O2365A |
| Source | TI SBOS365E (June 2006, revised August 2016), OPA365 / OPA2365 datasheet, p.25 (Package Option Addendum, Packaging Information, Device Marking column, dated 20-Jan-2016) and p.26 note (4) |
| How it is drawn | O2365A (TI Device Marking for OPA2365AIDR; the first character is the letter O), along the long axis, upright with pin 1 lower left, clear of the pin-1 dimple. TI note (4) says there may be additional marking for the logo, lot trace code or environmental category; TI publishes no layout or placeholder for those, so they are not drawn. |
| Placement | top face, flat light mark 5 um above the face (coplanar), in the Adom.LaserEtch group; along the long axis, upright in the standard pose (pin 1 lower left seen from the top) |
| Font | service-step2glb /laser-etch single-stroke outline font (not the manufacturer's font) |
| Gate | adom-aiflow-etch check: PASS (axis PASS, upright PASS, size PASS, band PASS, flat PASS, group PASS, colour PASS, widget PASS) |

The datasheet's marking figure (p.25):

3D models
| File | What it is |
|---|---|
| opa2365aidr-etched.step | The library model for board CAD (KiCad, Fusion, Altium): the package with the real marking in an Adom.LaserEtch group. |
| opa2365aidr.step | The same package, unmarked. |
| opa2365aidr-etched.glb | The marked model as GLB, clean for boards and digital twins (no pad outlines, labels or silkscreen), with matte-tin leads. |
| opa2365aidr-hero.glb | The annotated page hero (adom-hero 1.4): the marked chip plus teal dashed pad outlines, silkscreen with pin 1 and pad signal names. Display only, never for a board. |
| lod/ | Board-use detail levels (below). |
| provenance/previous/ | Earlier models, kept for reference: KiCad's library model and the hand-built square-fold model this page carried from 2026-10-19 to 2026-10-21. |
Frame for every file: Z up, seated on z = 0, centred on the KiCad footprint origin, pin 1 on footprint pad 1, binds with zero offset and rotation.
How the model is made (2026-10-21): with KiCad's own package generator (kicad-packages3D-generator, the CadQuery scripts behind KiCad's 3D library), so the leads have KiCad's real radiused gull-wing bends, run with the datasheet's values instead of the library's generic ones. TI SBOS365E p.31 (D, R-PDSO-G8, 4040047-3/M; JEDEC MS-012 AA): body 4.90 x 3.90, span 6.00, b 0.41, e 1.27 (printed mid/typ); A1 0.16, height 1.69, c 0.21 and L 0.46 to the gauge plane measured off TI's to-scale drawing (TI prints limits only); KiCad's bend radii 0.10, body draft 9 deg.
Why not KiCad's library model as it is: KiCad's shipped STEP is 38 um under TI's 0.40 mm minimum, so the package was regenerated with KiCad's own generator from TI's drawing values. Measured L foot to the 0.25 mm gauge plane: datasheet 0.40 / - / 1.27, KiCad library 0.362, regenerated 0.460 mm. Method: section through one lead's centre line (plane y = lead centre), cut at the 0.25 mm gauge plane (z = 0.25); L = distance from the lead tip to where the lead's lower outer surface crosses the gauge plane (JEDEC definition), provenance/tools/kicad-generator/measure.py.
Leads: before and after
The page carried a hand-built model with square 90 degree lead folds from 2026-10-19 to 2026-10-21. It is replaced by the generator's radiused bends, with the leads in their own matte-tin material:

Model proof: overlay on the datasheet drawing
The plain model was rendered orthographically at the drawing's own scale and blended over the datasheet's top and side/end views. Red outline and blue fill: the model. Black lines: the datasheet.

| Dimension (mm) | Datasheet min / typ / max | Model |
|---|---|---|
| Body length | 4.80 / - / 5.00 | 4.900 |
| Body width | 3.80 / - / 4.00 | 3.900 |
| Lead tip to tip | 5.80 / - / 6.20 | 6.000 |
| Overall height | max 1.75 | 1.690 |
| Standoff | 0.10 / - / 0.25 | 0.160 |
| Lead width | 0.31 / - / 0.51 | 0.410 |
| Lead thickness | 0.13 / - / 0.25 | 0.210 |
| Pitch | 1.27 | 1.270 |
| Foot (to the 0.25 mm gauge plane) | 0.40 / - / 1.27 | 0.460 (measured) |
| Foot angle | 0 to 8 deg | 0 deg (KiCad's generator draws a flat foot) |
| Bend radii (drawn curved, not printed) | - | 0.10, 0.10 |
Pin 1: KiCad's pin-1 dimple (generator default) inside TI's Pin 1 Index Area; TI does not specify its form. The marking was re-applied with the same reviewed inputs: etched with the same inputs as before (line O2365A, planner layout); gate PASS.
Cited datasheet pages:

Detail levels for board and digital-twin viewers
| Level | File | Triangles | Draw calls | Size | Marking |
|---|---|---|---|---|---|
| high | opa2365aidr-high.glb | 1884 | 4 | 69 KiB | yes |
| medium | opa2365aidr-medium.glb | 1884 | 4 | 51 KiB | yes |
| low | opa2365aidr-low.glb | 946 | 3 | 28 KiB | no |
| super-low | opa2365aidr-super-low.glb | 714 | 3 | 22 KiB | no |
All four levels come from the generated model, share the Z-up frame, units and seating of the library model, carry no footprint or silkscreen artwork, and keep the real terminals and the pin-1 cue. High is the marked model with its primitives batched per part (geometry unchanged); medium is the same, quantized; low and super-low are error-bounded simplifications without the marking (unreadable at those sizes). Status: candidate; the cached previews were inspected, a streaming LOD viewer has not qualified them.
Symbol chip outline
The symbol body carries the chip outline, so the schematic shows the same chip and marking as the 3D view. It was redrawn on 2026-10-21 from the new model: artwork/OPA2365AIDR-3d-outline-dark-named.svg, drawn from the marked model in adom-aiflow-etch outline's standard pose: the service draws the body outline and the name is the etched model's own mark edges, projected with the tool's calibration (provenance/tools/kicad-generator/mark_art.py); the tool's outline gate passes. adom-aiflow-etch outline itself now only composes a single-stroke name, which drops parts of the real mark. The KiCad symbol and the Fusion library (.lbr) carry the same drawing.

3D model provenance
provenance/3d-model.json records the datasheet (document, revision, pages, SHA-256), every model dimension against the datasheet, what was measured off the drawing, the generator, its parameters and the measurement (provenance/tools/kicad-generator/), the etch gate result, file hashes, tool versions and the AI-derived classification. PROVENANCE.md is the readable summary.
Datasheet provenance
# OPA2365AIDR
**Texas Instruments** · Operational Amplifier · SOIC-8
OPA2365AIDR from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol and footprint from KiCad-official CAD; the 3D model comes from KiCad's own package generator at the datasheet's values and carries TI's real Device Marking.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT A | output | Output of channel A. Rail-to-rail output stage; can swing to within millivolts of the supply rails under light load. |
| 2 | -IN A | input | Inverting input of channel A. Rail-to-rail input common-mode range (V- to V+). |
| 3 | +IN A | input | Non-inverting input of channel A. Rail-to-rail input common-mode range (V- to V+). |
| 4 | V- | power_in | Negative supply rail (or ground in single-supply operation). Total supply (V+ minus V-) range: 2.2 V to 5.5 V. |
| 5 | +IN B | input | Non-inverting input of channel B. Rail-to-rail input common-mode range (V- to V+). |
| 6 | -IN B | input | Inverting input of channel B. Rail-to-rail input common-mode range (V- to V+). |
| 7 | OUT B | output | Output of channel B. Rail-to-rail output stage; can swing to within millivolts of the supply rails under light load. |
| 8 | V+ | power_in | Positive supply rail. Total supply (V+ minus V-) range: 2.2 V to 5.5 V. Bypass with a 0.1 µF capacitor to V-/GND close to the pin. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | Op-amp/Cmp |
| Pins | 8 |
## Ordering variants
Same part, different packaging or reel option.
- `OPA2365AIDR`
- `OPA2365AIDRIDGKR`
- `OPA2365AIDRIDGK`
## CAD
- Symbol: `OPA2365AIDR` (KiCad, adom-symbol 1.2.6, chip outline baked in the body)
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm` (KiCad official)
- Fusion / EAGLE: [opa2365aidr.lbr](opa2365aidr.lbr)
## Top marking (the real one, from the datasheet)
Every 3D file on this page that carries a marking carries **the manufacturer's own top marking**, not an invented label:
| | |
|---|---|
| Marking | `O2365A` |
| Source | TI SBOS365E (June 2006, revised August 2016), OPA365 / OPA2365 datasheet, p.25 (Package Option Addendum, Packaging Information, Device Marking column, dated 20-Jan-2016) and p.26 note (4) |
| How it is drawn | O2365A (TI Device Marking for OPA2365AIDR; the first character is the letter O), along the long axis, upright with pin 1 lower left, clear of the pin-1 dimple. TI note (4) says there may be additional marking for the logo, lot trace code or environmental category; TI publishes no layout or placeholder for those, so they are not drawn. |
| Placement | top face, flat light mark 5 um above the face (coplanar), in the Adom.LaserEtch group; along the long axis, upright in the standard pose (pin 1 lower left seen from the top) |
| Font | service-step2glb /laser-etch single-stroke outline font (not the manufacturer's font) |
| Gate | `adom-aiflow-etch check`: **PASS** (axis PASS, upright PASS, size PASS, band PASS, flat PASS, group PASS, colour PASS, widget PASS) |

The datasheet's marking figure (p.25):

## 3D models
::adom-models{src="/adom/opa2365aidr/render/models.json"}
| File | What it is |
|---|---|
| [opa2365aidr-etched.step](opa2365aidr-etched.step) | **The library model** for board CAD (KiCad, Fusion, Altium): the package with the real marking in an `Adom.LaserEtch` group. |
| [opa2365aidr.step](opa2365aidr.step) | The same package, unmarked. |
| [opa2365aidr-etched.glb](opa2365aidr-etched.glb) | The marked model as GLB, clean for boards and digital twins (no pad outlines, labels or silkscreen), with matte-tin leads. |
| [opa2365aidr-hero.glb](opa2365aidr-hero.glb) | The annotated page hero (adom-hero 1.4): the marked chip plus teal dashed pad outlines, silkscreen with pin 1 and pad signal names. Display only, never for a board. |
| [lod/](lod/manifest.json) | Board-use detail levels (below). |
| [provenance/previous/](provenance/previous/opa2365aidr-kicad-generic.step) | Earlier models, kept for reference: KiCad's library model and the hand-built square-fold model this page carried from 2026-10-19 to 2026-10-21. |
Frame for every file: Z up, seated on z = 0, centred on the KiCad footprint origin, pin 1 on footprint pad 1, binds with zero offset and rotation.
**How the model is made (2026-10-21):** with **KiCad's own package generator** (kicad-packages3D-generator, the CadQuery scripts behind KiCad's 3D library), so the leads have KiCad's real radiused gull-wing bends, run with the datasheet's values instead of the library's generic ones. TI SBOS365E p.31 (D, R-PDSO-G8, 4040047-3/M; JEDEC MS-012 AA): body 4.90 x 3.90, span 6.00, b 0.41, e 1.27 (printed mid/typ); A1 0.16, height 1.69, c 0.21 and L 0.46 to the gauge plane measured off TI's to-scale drawing (TI prints limits only); KiCad's bend radii 0.10, body draft 9 deg.
**Why not KiCad's library model as it is:** KiCad's shipped STEP is 38 um under TI's 0.40 mm minimum, so the package was regenerated with KiCad's own generator from TI's drawing values. Measured L foot to the 0.25 mm gauge plane: datasheet 0.40 / - / 1.27, KiCad library 0.362, regenerated 0.460 mm. Method: section through one lead's centre line (plane y = lead centre), cut at the 0.25 mm gauge plane (z = 0.25); L = distance from the lead tip to where the lead's lower outer surface crosses the gauge plane (JEDEC definition), provenance/tools/kicad-generator/measure.py.
## Leads: before and after
The page carried a hand-built model with square 90 degree lead folds from 2026-10-19 to 2026-10-21. It is replaced by the generator's radiused bends, with the leads in their own matte-tin material:

## Model proof: overlay on the datasheet drawing
The plain model was rendered orthographically at the drawing's own scale and blended over the datasheet's top and side/end views. Red outline and blue fill: the model. Black lines: the datasheet.

| Dimension (mm) | Datasheet min / typ / max | Model |
|---|---|---|
| Body length | 4.80 / - / 5.00 | 4.900 |
| Body width | 3.80 / - / 4.00 | 3.900 |
| Lead tip to tip | 5.80 / - / 6.20 | 6.000 |
| Overall height | max 1.75 | 1.690 |
| Standoff | 0.10 / - / 0.25 | 0.160 |
| Lead width | 0.31 / - / 0.51 | 0.410 |
| Lead thickness | 0.13 / - / 0.25 | 0.210 |
| Pitch | 1.27 | 1.270 |
| Foot (to the 0.25 mm gauge plane) | 0.40 / - / 1.27 | 0.460 (measured) |
| Foot angle | 0 to 8 deg | 0 deg (KiCad's generator draws a flat foot) |
| Bend radii (drawn curved, not printed) | - | 0.10, 0.10 |
Pin 1: KiCad's pin-1 dimple (generator default) inside TI's Pin 1 Index Area; TI does not specify its form. The marking was re-applied with the same reviewed inputs: etched with the same inputs as before (line O2365A, planner layout); gate PASS.
Cited datasheet pages:


## Detail levels for board and digital-twin viewers
::adom-component-lod{src="/adom/opa2365aidr/render/lod/manifest.json"}
| Level | File | Triangles | Draw calls | Size | Marking |
|---|---|---|---|---|---|
| high | [opa2365aidr-high.glb](lod/opa2365aidr-high.glb) | 1884 | 4 | 69 KiB | yes |
| medium | [opa2365aidr-medium.glb](lod/opa2365aidr-medium.glb) | 1884 | 4 | 51 KiB | yes |
| low | [opa2365aidr-low.glb](lod/opa2365aidr-low.glb) | 946 | 3 | 28 KiB | no |
| super-low | [opa2365aidr-super-low.glb](lod/opa2365aidr-super-low.glb) | 714 | 3 | 22 KiB | no |
All four levels come from the generated model, share the Z-up frame, units and seating of the library model, carry no footprint or silkscreen artwork, and keep the real terminals and the pin-1 cue. High is the marked model with its primitives batched per part (geometry unchanged); medium is the same, quantized; low and super-low are error-bounded simplifications without the marking (unreadable at those sizes). Status: candidate; the cached previews were inspected, a streaming LOD viewer has not qualified them.
## Symbol chip outline
The symbol body carries the chip outline, so the schematic shows the same chip and marking as the 3D view. It was redrawn on 2026-10-21 from the new model: [artwork/OPA2365AIDR-3d-outline-dark-named.svg](artwork/OPA2365AIDR-3d-outline-dark-named.svg), drawn from the marked model in `adom-aiflow-etch outline`'s standard pose: the service draws the body outline and the name is the etched model's own mark edges, projected with the tool's calibration ([provenance/tools/kicad-generator/mark_art.py](provenance/tools/kicad-generator/mark_art.py)); the tool's outline gate passes. `adom-aiflow-etch outline` itself now only composes a single-stroke name, which drops parts of the real mark. The KiCad symbol and the Fusion library (.lbr) carry the same drawing.

## 3D model provenance
[provenance/3d-model.json](provenance/3d-model.json) records the datasheet (document, revision, pages, SHA-256), every model dimension against the datasheet, what was measured off the drawing, the generator, its parameters and the measurement ([provenance/tools/kicad-generator/](provenance/tools/kicad-generator/kgen.py)), the etch gate result, file hashes, tool versions and the AI-derived classification. [PROVENANCE.md](PROVENANCE.md) is the readable summary.
## Datasheet provenance
- **Datasheet:** TI SBOS365E (June 2006, revised August 2016), OPA365 / OPA2365 datasheet ([PDF](docs/opa2365aidr-datasheet.pdf), [ti.com](https://www.ti.com/lit/ds/symlink/opa2365.pdf), sha256 `6ae14860e4178ed1`, 33 pages).
- **Pins:** extracted by `ds2sf` (Claude); every pin cites a datasheet page.