main
Ray
Publish 0.1.0
403f596
NSi8242W0-Q1SWR
NOVOSENSE · Digital Isolators · SOP-16-300mil
NSi8242W0-Q1SWR from NOVOSENSE, in a SOP-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD1 | power_in | Power supply for isolator side 1, with a recommended supply range of 2.5V to 5.5V. |
| 2 | GND1 | power_in | Ground 1, the ground reference for isolator side 1. |
| 3 | INA | input | Logic input A on side 1. |
| 4 | INB | input | Logic input B on side 1. |
| 5 | OUTC | output | Logic output C on side 2, with an output impedance of approximately 50 ohm. |
| 6 | OUTD | output | Logic output D on side 2, with an output impedance of approximately 50 ohm. |
| 7 | NC/EN1 | input | No connection, or output enable 1: an active-high input where side 1 output is enabled when EN1 is high or NC and set to high impedance when EN1 is low. |
| 8 | GND1 | power_in | Ground 1, the ground reference for isolator side 1. |
| 9 | GND2 | power_in | Ground 2, the ground reference for isolator side 2. |
| 10 | EN2 | input | Output enable 2: an active-high input where side 2 output is enabled when EN2 is high or NC and set to high impedance when EN2 is low. |
| 11 | IND | input | Logic input D on side 1. |
| 12 | INC | input | Logic input C on side 1. |
| 13 | OUTB | output | Logic output B on side 2, with an output impedance of approximately 50 ohm. |
| 14 | OUTA | output | Logic output A on side 2, with an output impedance of approximately 50 ohm. |
| 15 | GND2 | power_in | Ground 2, the ground reference for isolator side 2. |
| 16 | VDD2 | power_in | Power supply for isolator side 2, with a recommended supply range of 2.5V to 5.5V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NOVOSENSE |
| Package | SOP-16-300mil |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power Supply Voltage | VDD1, VDD2 | -0.5 | 6.5 | V | 4 | ||
| Maximum Input Voltage | VINA, VINB, VINC, VIND | -0.4 | V | max VDD+0.4 V; must not exceed 6.5V | 4 | ||
| Maximum Output Voltage | VOUTA, VOUTB, VOUTC, VOUTD | -0.4 | V | max VDD+0.4 V; must not exceed 6.5V | 4 | ||
| Maximum Input/Output Pulse Voltage | VINA, VINB, VINC, VIND, VOUTA, VOUTB, VOUTC, VOUTD | -0.8 | V | pulse width less than 100ns, duty cycle less than 10%; max VDD+0.8 V | 4 | ||
| Output current | Io | -15 | 15 | mA | 4 | ||
| Maximum Surge Isolation Voltage | VIOSM | 6.25 | kV | 4 | |||
| Operating Temperature | Topr | -40 | 125 | ℃ | 4 | ||
| Junction Temperature | Tj | 150 | ℃ | 4 | |||
| Storage Temperature | Tstg | -65 | 150 | ℃ | 4 | ||
| Electrostatic discharge HBM | HBM | -8000 | 8000 | V | HBM, printed ±8000 V | 4 | |
| Electrostatic discharge CDM | CDM | -2000 | 2000 | V | CDM, printed ±2000 V | 4 | |
| Power Supply Voltage | VDD1, VDD2 | 2.5 | 5.5 | V | 4 | ||
| Operating Temperature | Topr | -40 | 125 | ℃ | 4 | ||
| High Level Input Voltage | VIH | 2 | V | 4 | |||
| Low Level Input Voltage | VIL | 0.8 | V | 4 | |||
| Data rate | DR | 150 | Mbps | 4 | |||
| IC Junction-to-Air Thermal Resistance SOP16(300mil) | θJA | 78.9 | ℃/W | SOP16(300mil) package | 5 | ||
| Junction-to-case (top) thermal resistance SOP16(300mil) | θJC(top) | 41.6 | ℃/W | SOP16(300mil) package | 5 | ||
| Junction-to-board thermal resistance SOP16(300mil) | θJB | 43.6 | ℃/W | SOP16(300mil) package | 5 | ||
| Low Level Output Voltage | VOL | 0.4 | V | IOL = 4mA | 5 | ||
| Common Mode Transient Immunity | CMTI | -200 | 200 | kV/us | Typ ±250 kV/us; See Figure 5.11, CL = 15pF | 5 | |
| Input Pull high or low Current | Ipull | 8 | 15 | uA | 5 | ||
| High Level Input Voltage | VIH | 2 | V | 5 | |||
| Low Level Input Voltage | VIL | 0.8 | V | 5 | |||
| Supply current IDD1(Q0) | IDD1(Q0) | 2.09 | 3.44 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 5V | 6 | |
| Supply current IDD2(Q0) | IDD2(Q0) | 2.09 | 3.44 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 5V | 6 | |
| Supply current IDD1(Q1) | IDD1(Q1) | 4.14 | 6.83 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 5V | 6 | |
| Supply current IDD2(Q1) | IDD2(Q1) | 4.14 | 6.83 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 5V | 6 | |
| Supply current IDD1(1M) | IDD1(1M) | 3.09 | 4.635 | mA | All Input with 1Mbps, CL=15pF, VDD 5V | 6 | |
| Supply current IDD2(1M) | IDD2(1M) | 3.09 | 4.635 | mA | All Input with 1Mbps, CL=15pF, VDD 5V | 6 | |
| Supply current IDD1(10M) | IDD1(10M) | 3.91 | 5.865 | mA | All Input with 10Mbps, CL=15pF, VDD 5V | 6 | |
| Supply current IDD2(10M) | IDD2(10M) | 3.91 | 5.865 | mA | All Input with 10Mbps, CL=15pF, VDD 5V | 6 | |
| Supply current IDD1(100M) | IDD1(100M) | 11.71 | 21.22 | mA | All Input with 100Mbps, CL=15pF, VDD 5V | 6 | |
| Supply current IDD2(100M) | IDD2(100M) | 11.71 | 21.22 | mA | All Input with 100Mbps, CL=15pF, VDD 5V | 6 | |
| Supply current IDD1(Q0) | IDD1(Q0) | 2.03 | 3.35 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 3.3V | 7 | |
| Supply current IDD2(Q0) | IDD2(Q0) | 2.03 | 3.35 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 3.3V | 7 | |
| Supply current IDD1(Q1) | IDD1(Q1) | 4.08 | 6.72 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 3.3V | 7 | |
| Supply current IDD2(Q1) | IDD2(Q1) | 4.08 | 6.72 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 3.3V | 7 | |
| Supply current IDD1(1M) | IDD1(1M) | 2.97 | 4.455 | mA | All Input with 1Mbps, CL=15pF, VDD 3.3V | 7 | |
| Supply current IDD2(1M) | IDD2(1M) | 2.97 | 4.455 | mA | All Input with 1Mbps, CL=15pF, VDD 3.3V | 7 | |
| Supply current IDD1(10M) | IDD1(10M) | 3.51 | 5.265 | mA | All Input with 10Mbps, CL=15pF, VDD 3.3V | 7 | |
| Supply current IDD2(10M) | IDD2(10M) | 3.51 | 5.265 | mA | All Input with 10Mbps, CL=15pF, VDD 3.3V | 7 | |
| Supply current IDD1(100M) | IDD1(100M) | 8.7 | 14.93 | mA | All Input with 100Mbps, CL=15pF, VDD 3.3V | 7 | |
| Supply current IDD2(100M) | IDD2(100M) | 8.7 | 14.93 | mA | All Input with 100Mbps, CL=15pF, VDD 3.3V | 7 | |
| Supply current IDD1(Q0) | IDD1(Q0) | 2 | 3.29 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 2.5V | 8 | |
| Supply current IDD2(Q0) | IDD2(Q0) | 2 | 3.29 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 2.5V | 8 | |
| Supply current IDD1(Q1) | IDD1(Q1) | 4.01 | 6.62 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 2.5V | 8 | |
| Supply current IDD2(Q1) | IDD2(Q1) | 4.01 | 6.62 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 2.5V | 8 | |
| Supply current IDD1(1M) | IDD1(1M) | 2.91 | 4.365 | mA | All Input with 1Mbps, CL=15pF, VDD 2.5V | 8 | |
| Supply current IDD2(1M) | IDD2(1M) | 2.91 | 4.365 | mA | All Input with 1Mbps, CL=15pF, VDD 2.5V | 8 | |
| Supply current IDD1(10M) | IDD1(10M) | 3.32 | 4.98 | mA | All Input with 10Mbps, CL=15pF, VDD 2.5V | 8 | |
| Supply current IDD2(10M) | IDD2(10M) | 3.32 | 4.98 | mA | All Input with 10Mbps, CL=15pF, VDD 2.5V | 8 | |
| Supply current IDD1(100M) | IDD1(100M) | 7.2 | 12.21 | mA | All Input with 100Mbps, CL=15pF, VDD 2.5V | 8 | |
| Supply current IDD2(100M) | IDD2(100M) | 7.2 | 12.21 | mA | All Input with 100Mbps, CL=15pF, VDD 2.5V | 8 |
CAD (KiCad official)
- Symbol:
NSi8242W0-Q1SWR - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOP-16-300mil (KiCad packages3D, STEP)
- 3D model files:
nsi8242w0-q1swr-etched.step/nsi8242w0-q1swr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);nsi8242w0-q1swr.step/nsi8242w0-q1swr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: NOVOSENSE datasheet, copy hosted by LCSC (31 pp, sha256
6a248adae188813c, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# NSi8242W0-Q1SWR
**NOVOSENSE** · Digital Isolators · SOP-16-300mil
NSi8242W0-Q1SWR from NOVOSENSE, in a SOP-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD1 | power_in | Power supply for isolator side 1, with a recommended supply range of 2.5V to 5.5V. |
| 2 | GND1 | power_in | Ground 1, the ground reference for isolator side 1. |
| 3 | INA | input | Logic input A on side 1. |
| 4 | INB | input | Logic input B on side 1. |
| 5 | OUTC | output | Logic output C on side 2, with an output impedance of approximately 50 ohm. |
| 6 | OUTD | output | Logic output D on side 2, with an output impedance of approximately 50 ohm. |
| 7 | NC/EN1 | input | No connection, or output enable 1: an active-high input where side 1 output is enabled when EN1 is high or NC and set to high impedance when EN1 is low. |
| 8 | GND1 | power_in | Ground 1, the ground reference for isolator side 1. |
| 9 | GND2 | power_in | Ground 2, the ground reference for isolator side 2. |
| 10 | EN2 | input | Output enable 2: an active-high input where side 2 output is enabled when EN2 is high or NC and set to high impedance when EN2 is low. |
| 11 | IND | input | Logic input D on side 1. |
| 12 | INC | input | Logic input C on side 1. |
| 13 | OUTB | output | Logic output B on side 2, with an output impedance of approximately 50 ohm. |
| 14 | OUTA | output | Logic output A on side 2, with an output impedance of approximately 50 ohm. |
| 15 | GND2 | power_in | Ground 2, the ground reference for isolator side 2. |
| 16 | VDD2 | power_in | Power supply for isolator side 2, with a recommended supply range of 2.5V to 5.5V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NOVOSENSE |
| Package | SOP-16-300mil |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power Supply Voltage | VDD1, VDD2 | -0.5 | | 6.5 | V | | 4 |
| Maximum Input Voltage | VINA, VINB, VINC, VIND | -0.4 | | | V | max VDD+0.4 V; must not exceed 6.5V | 4 |
| Maximum Output Voltage | VOUTA, VOUTB, VOUTC, VOUTD | -0.4 | | | V | max VDD+0.4 V; must not exceed 6.5V | 4 |
| Maximum Input/Output Pulse Voltage | VINA, VINB, VINC, VIND, VOUTA, VOUTB, VOUTC, VOUTD | -0.8 | | | V | pulse width less than 100ns, duty cycle less than 10%; max VDD+0.8 V | 4 |
| Output current | Io | -15 | | 15 | mA | | 4 |
| Maximum Surge Isolation Voltage | VIOSM | | | 6.25 | kV | | 4 |
| Operating Temperature | Topr | -40 | | 125 | ℃ | | 4 |
| Junction Temperature | Tj | | | 150 | ℃ | | 4 |
| Storage Temperature | Tstg | -65 | | 150 | ℃ | | 4 |
| Electrostatic discharge HBM | HBM | -8000 | | 8000 | V | HBM, printed ±8000 V | 4 |
| Electrostatic discharge CDM | CDM | -2000 | | 2000 | V | CDM, printed ±2000 V | 4 |
| Power Supply Voltage | VDD1, VDD2 | 2.5 | | 5.5 | V | | 4 |
| Operating Temperature | Topr | -40 | | 125 | ℃ | | 4 |
| High Level Input Voltage | VIH | 2 | | | V | | 4 |
| Low Level Input Voltage | VIL | | | 0.8 | V | | 4 |
| Data rate | DR | | | 150 | Mbps | | 4 |
| IC Junction-to-Air Thermal Resistance SOP16(300mil) | θJA | | 78.9 | | ℃/W | SOP16(300mil) package | 5 |
| Junction-to-case (top) thermal resistance SOP16(300mil) | θJC(top) | | 41.6 | | ℃/W | SOP16(300mil) package | 5 |
| Junction-to-board thermal resistance SOP16(300mil) | θJB | | 43.6 | | ℃/W | SOP16(300mil) package | 5 |
| Low Level Output Voltage | VOL | | | 0.4 | V | IOL = 4mA | 5 |
| Common Mode Transient Immunity | CMTI | -200 | | 200 | kV/us | Typ ±250 kV/us; See Figure 5.11, CL = 15pF | 5 |
| Input Pull high or low Current | Ipull | 8 | 15 | | uA | | 5 |
| High Level Input Voltage | VIH | 2 | | | V | | 5 |
| Low Level Input Voltage | VIL | | | 0.8 | V | | 5 |
| Supply current IDD1(Q0) | IDD1(Q0) | | 2.09 | 3.44 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 5V | 6 |
| Supply current IDD2(Q0) | IDD2(Q0) | | 2.09 | 3.44 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 5V | 6 |
| Supply current IDD1(Q1) | IDD1(Q1) | | 4.14 | 6.83 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 5V | 6 |
| Supply current IDD2(Q1) | IDD2(Q1) | | 4.14 | 6.83 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 5V | 6 |
| Supply current IDD1(1M) | IDD1(1M) | | 3.09 | 4.635 | mA | All Input with 1Mbps, CL=15pF, VDD 5V | 6 |
| Supply current IDD2(1M) | IDD2(1M) | | 3.09 | 4.635 | mA | All Input with 1Mbps, CL=15pF, VDD 5V | 6 |
| Supply current IDD1(10M) | IDD1(10M) | | 3.91 | 5.865 | mA | All Input with 10Mbps, CL=15pF, VDD 5V | 6 |
| Supply current IDD2(10M) | IDD2(10M) | | 3.91 | 5.865 | mA | All Input with 10Mbps, CL=15pF, VDD 5V | 6 |
| Supply current IDD1(100M) | IDD1(100M) | | 11.71 | 21.22 | mA | All Input with 100Mbps, CL=15pF, VDD 5V | 6 |
| Supply current IDD2(100M) | IDD2(100M) | | 11.71 | 21.22 | mA | All Input with 100Mbps, CL=15pF, VDD 5V | 6 |
| Supply current IDD1(Q0) | IDD1(Q0) | | 2.03 | 3.35 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 3.3V | 7 |
| Supply current IDD2(Q0) | IDD2(Q0) | | 2.03 | 3.35 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 3.3V | 7 |
| Supply current IDD1(Q1) | IDD1(Q1) | | 4.08 | 6.72 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 3.3V | 7 |
| Supply current IDD2(Q1) | IDD2(Q1) | | 4.08 | 6.72 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 3.3V | 7 |
| Supply current IDD1(1M) | IDD1(1M) | | 2.97 | 4.455 | mA | All Input with 1Mbps, CL=15pF, VDD 3.3V | 7 |
| Supply current IDD2(1M) | IDD2(1M) | | 2.97 | 4.455 | mA | All Input with 1Mbps, CL=15pF, VDD 3.3V | 7 |
| Supply current IDD1(10M) | IDD1(10M) | | 3.51 | 5.265 | mA | All Input with 10Mbps, CL=15pF, VDD 3.3V | 7 |
| Supply current IDD2(10M) | IDD2(10M) | | 3.51 | 5.265 | mA | All Input with 10Mbps, CL=15pF, VDD 3.3V | 7 |
| Supply current IDD1(100M) | IDD1(100M) | | 8.7 | 14.93 | mA | All Input with 100Mbps, CL=15pF, VDD 3.3V | 7 |
| Supply current IDD2(100M) | IDD2(100M) | | 8.7 | 14.93 | mA | All Input with 100Mbps, CL=15pF, VDD 3.3V | 7 |
| Supply current IDD1(Q0) | IDD1(Q0) | | 2 | 3.29 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 2.5V | 8 |
| Supply current IDD2(Q0) | IDD2(Q0) | | 2 | 3.29 | mA | All Input 0V for NSi8242x0 Or All Input at supply for NSi8242x1, VDD 2.5V | 8 |
| Supply current IDD1(Q1) | IDD1(Q1) | | 4.01 | 6.62 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 2.5V | 8 |
| Supply current IDD2(Q1) | IDD2(Q1) | | 4.01 | 6.62 | mA | All Input at supply for NSi8242x0 Or All Input 0V for NSi8242x1, VDD 2.5V | 8 |
| Supply current IDD1(1M) | IDD1(1M) | | 2.91 | 4.365 | mA | All Input with 1Mbps, CL=15pF, VDD 2.5V | 8 |
| Supply current IDD2(1M) | IDD2(1M) | | 2.91 | 4.365 | mA | All Input with 1Mbps, CL=15pF, VDD 2.5V | 8 |
| Supply current IDD1(10M) | IDD1(10M) | | 3.32 | 4.98 | mA | All Input with 10Mbps, CL=15pF, VDD 2.5V | 8 |
| Supply current IDD2(10M) | IDD2(10M) | | 3.32 | 4.98 | mA | All Input with 10Mbps, CL=15pF, VDD 2.5V | 8 |
| Supply current IDD1(100M) | IDD1(100M) | | 7.2 | 12.21 | mA | All Input with 100Mbps, CL=15pF, VDD 2.5V | 8 |
| Supply current IDD2(100M) | IDD2(100M) | | 7.2 | 12.21 | mA | All Input with 100Mbps, CL=15pF, VDD 2.5V | 8 |
## CAD (KiCad official)
- Symbol: `NSi8242W0-Q1SWR`
- Footprint: `Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm`
- 3D model: SOP-16-300mil (KiCad packages3D, STEP)
- 3D model files: `nsi8242w0-q1swr-etched.step` / `nsi8242w0-q1swr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `nsi8242w0-q1swr.step` / `nsi8242w0-q1swr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [NOVOSENSE datasheet, copy hosted by LCSC](docs/nsi8242w0-q1swr-datasheet.pdf) (31 pp, sha256 `6a248adae188813c`, retrieved 2026-11-20)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/nsi8242w0-q1swr-datasheet.pdf)