main
Ray
Publish 0.1.0
9f5db47
NCV97310MW33AR2G
onsemi · Power Management Specialized - PMIC · QFN-32-EP(5x5)
NCV97310MW33AR2G from onsemi, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Battery input voltage that must be tied to pin 29 VINL, with an input filter capacitor placed close to the pin. |
| 2 | EN | input | High-voltage TTL-compatible master enable; grounding this input stops all outputs and reduces Iq to a minimum (shutdown mode). |
| 3 | STBYB | input | High-voltage TTL-compatible mode select; grounding this input activates the low-Iq standby mode for switcher 1. |
| 4 | RDEPTH | passive | Sets the modulation depth (% of FSW) for spread spectrum with a resistor to GND. |
| 5 | RMOD | passive | Sets the modulation frequency for spread spectrum with a resistor to GND. |
| 6 | RSTB1 | output | Reset output with adjustable delay that goes low when the output is out of regulation; in Low-Iq LDO mode it needs a pull-up to a permanent external supply such as VOUT1. |
| 7 | COMP1 | passive | Output of the error amplifier for switcher 1. |
| 8 | ROSC | passive | Provides frequency adjustment for the switching oscillator. |
| 9 | ERRB | output | Error flag combining temperature, input voltage and output voltage sensing. |
| 10 | EN2 | input | TTL-compatible low-voltage input; grounding this input stops switcher 2. |
| 11 | RSTB2 | output | Reset output with adjustable delay that goes low when the switcher 2 output is out of regulation. |
| 12 | GND1 | power_in | Ground reference for the IC, which the exposed pad must also be connected to. |
| 13 | RSTB3 | output | Reset output with adjustable delay that goes low when the switcher 3 output is out of regulation. |
| 14 | FB3 | input | Output voltage sensing input for switcher 3 that provides output voltage adjustability. |
| 15 | EN3 | input | TTL-compatible low-voltage input; grounding this input stops switcher 3. |
| 16 | BST3 | passive | Bootstrap input that supplies high-side N-channel drive voltage above VIN3 for optimum RDS(on) and efficiency. |
| 17 | GND3 | power_in | Ground connection for the source of the switcher 3 low-side switch. |
| 18 | SW3L | passive | Drain of the switcher 3 low-side switch that connects to the output inductor and must be tied to SW3H. |
| 19 | SW3H | passive | Source of the switcher 3 high-side switch that connects to the output inductor and must be tied to SW3L. |
| 20 | VDRV2 | passive | Internal supply for driving the low-voltage internal switches, which needs a noise-filter capacitor. |
| 21 | VIN3 | power_in | Low input voltage for switcher 3 that must be tied to pin 22 VIN2 and pin 28 VOUT, with an input filter capacitor close to the pin. |
| 22 | VIN2 | power_in | Low input voltage for switcher 2 that must be tied to pin 21 VIN3 and pin 28 VOUT, with an input filter capacitor close to the pin. |
| 23 | SW2 | passive | Switching node of the switcher 2 regulator that connects to the output inductor. |
| 24 | GND2 | power_in | Ground connection for the source of the switcher 2 low-side switch. |
| 25 | BST2 | passive | Bootstrap input that supplies high-side N-channel drive voltage above VIN2 for optimum RDS(on) and efficiency. |
| 26 | NC | unconnected | No-connect pin that must be left floating. |
| 27 | FB2 | input | Output voltage sensing input for switcher 2 that provides output voltage adjustability. |
| 28 | VOUT | power_out | Output voltage sensing pin that delivers the output current in low-Iq mode and must be tied to VIN2 and VIN3. |
| 29 | VINL | power_in | Battery input voltage that must be tied to pin 1 VBAT, with an input filter capacitor close to the pin. |
| 30 | BST1 | passive | Bootstrap input that supplies N-channel power switch drive voltage above VBAT for optimum Rdson and efficiency. |
| 31 | VDRV1 | passive | Internal supply for driving the low-voltage internal switch, which needs a noise-filter capacitor. |
| 32 | SW1 | passive | Switching node of the regulator that connects the output inductor and the freewheeling diode cathode. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | QFN-32-EP(5x5) |
| Category | Power Management ICs |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage from battery (VBAT, VINL) | VBAT, VINL | -0.3 | 45 | V | 4 | ||
| Max voltage VBAT to SW1 | 45 | V | 4 | ||||
| Min/Max voltage SW1 | SW1 | -0.7 | 40 | V | 4 | ||
| Min voltage SW1, SW2, SW3 | SW1, SW2, SW3 | -3 | V | 20 ns | 4 | ||
| Min/Max voltage BST1, STBYB, EN | BST1, STBYB, EN | -0.3 | 40 | V | 4 | ||
| Min/Max voltage VIN2, VIN3, BST2, BST3, SW2, SW3H, SW3L, VOUT | VIN2, VIN3, BST2, BST3, SW2, SW3H, SW3L, VOUT | -0.3 | 12 | V | 4 | ||
| Min/Max voltage on RSTB2, RSTB3, EN2, EN3, FB2, FB3 | RSTB2, RSTB3, EN2, EN3, FB2, FB3 | -0.3 | 6 | V | 4 | ||
| Min/Max voltage on RSTB1, ERRB | RSTB1, ERRB | -0.3 | 3.6 | V | 4 | ||
| Max voltage BST1 to SW1, BST2 to SW2, BST3 to SWx | 3.6 | V | 4 | ||||
| Min/Max voltage VDRV1, VDRV2, COMP1, ROSC, RMOD, RDEPTH | VDRV1, VDRV2, COMP1, ROSC, RMOD, RDEPTH | -0.3 | 3.6 | V | 4 | ||
| Thermal resistance junction to ambient, 5x5 QFN | RJA | 25 | C/W | Mounted on 1 sq. in. of 4-layer PCB, 1 oz. copper | 4 | ||
| Storage temperature range | -55 | 150 | C | 4 | |||
| Operating junction temperature range | TJ | -40 | 150 | C | 4 | ||
| ESD withstand voltage, human body model | VESD | 2 | kV | Human body model | 4 | ||
| ESD withstand voltage, machine model | VESD | 200 | V | Machine model | 4 | ||
| VIN range | VIN | 4.5 | 36 | V | 4 | ||
| Ambient temperature range | TA | -40 | 125 | C | 4 | ||
| Quiescent current, shutdown | IqSD | 8 | 12 | µA | VBAT = VINL = 13.2 V, TJ=25C, VEN = 0 V | 6 | |
| Quiescent current, standby | IqEN | 25 | 35 | µA | VBAT = VINL = 13.2 V, TJ=25C, VEN = 3 V, VSTBYB = VEN2 = VEN3 = 0 V | 6 | |
| VBAT UVLO start threshold | VUV1ST | 4.45 | 4.85 | V | VBAT rising | 6 | |
| VBAT UVLO stop threshold | VUV1SP | 3.7 | 4.1 | V | VBAT falling | 6 | |
| Enable logic low | VENLO, VEN2LO, VEN3LO, VSTBYBLO | 0.8 | V | Voltage input needed to guarantee logic low | 6 | ||
| Enable logic high | VENHI, VEN2HI, VEN3HI, VSTBYBHI | 2 | V | Voltage input needed to guarantee logic high | 6 | ||
| Enable pin input current | IEN | 0.125 | 1 | µA | VEN = 5 V | 6 | |
| STBYB pin input current | ISTBYB | 0.5 | 2 | µA | VSTBYB = 5 V | 6 | |
| Enable pin input current, EN2/EN3 | IEN2, IEN3 | 30 | 50 | 70 | µA | VEN2 = VEN3 = 5 V | 6 |
| Switcher 1 start-up time | tSTBYB | 60 | 200 | µs | STBYB high to switcher 1 ready | 6 | |
| Switcher 1 output voltage | VOUT | 3.23 | 3.3 | 3.37 | V | 6 | |
| VOUT line regulation in low-Iq mode | VLine1 | 5 | 25 | mV | IOUT = 50 mA, VSTBYB = 0 V, 6 V < VINL = VBAT < 28 V | 6 | |
| VOUT load regulation in low-Iq mode | VLoad1 | 10 | 35 | mV | VINL = VBAT = 13.2 V, VSTBYB = 0 V, 1 mA < IOUT < 150 mA | 6 | |
| Voltage drop-out in low-Iq mode | VDROP1 | 500 | mV | IOUT = 150 mA, VSTBYB = 0 V | 6 | ||
| Switchers 2 and 3 FB pin voltage during regulation | VFB2R, VFB3R | 1.179 | 1.2 | 1.221 | V | OUTx connected to FBx through a 10 k resistor | 6 |
| Error amplifier transconductance, switcher 1 | gm | 0.6 | 1 | 1.4 | mmho | VCOMP = 1.1 V, 4.5 V < VBAT < 18 V | 6 |
| Error amplifier transconductance, high VBAT | gm(HV) | 0.35 | 0.55 | 0.75 | mmho | VCOMP = 1.1 V, 20 V < VBAT < 28 V | 6 |
| COMP source current limit | ISOURCE | 50 | 75 | 100 | µA | VOUT = 4.0 V, VCOMP = 1.1 V, 4.5 V < VBAT < 18 V | 6 |
| Minimum COMP voltage | VCMPMIN | 0.15 | 0.3 | V | VOUT = 6.0 V | 6 | |
| Switching frequency, switcher 1 | fSW1 | 1.8 | 2 | 2.2 | MHz | 4.5 < VBAT < 18 V, ROSC = open | 7 |
| Switching frequency, switcher 1, high VBAT | fSW1(HV) | 0.9 | 1 | 1.1 | MHz | 20 V < VBAT < 28 V, ROSC = open | 7 |
| Switching frequency, ROSC | fROSC | 2.3 | 2.5 | 2.8 | MHz | ROSC = 12.5 k | 7 |
| ROSC reference voltage | VROSC | 0.9 | 1 | 1.1 | V | ROSC = 25 k | 7 |
| Frequency foldback threshold, rising | VFL1U | 18.4 | 20 | V | VBAT rising | 7 | |
| Frequency foldback threshold, falling | VFL1D | 18 | 19.8 | V | VBAT falling | 7 | |
| Ramp slope, switcher 1 | Sramp1 | 1.8 | 3.4 | A/s | 4.5 < VBAT < 18 V | 7 | |
| ON resistance, switcher 1 power switch | RDS1ON | 185 | 360 | mΩ | VBST1 = VSW1 + 3.0 V, ISW1 = 500 mA | 7 | |
| Leakage current VBAT to SW1 | ILKSW1 | 10 | µA | VEN = 0 V, VSW1 = 0, VBAT = 18 V | 7 | ||
| Minimum ON time, switcher 1 | tON1MIN | 45 | 70 | ns | Measured at SW1 pin | 7 | |
| Minimum OFF time, switcher 1 | tOFF1MIN | 30 | 50 | 70 | ns | Measured at SW1 pin | 7 |
| High-side ON resistance, switcher 2 | RHS2ON | 165 | 300 | mΩ | VBST2 = VSW2 + 3.0 V, ISW2 = 500 mA | 7 | |
| Low-side ON resistance, switcher 2 | RLS2ON | 130 | 230 | mΩ | ISW2 = 500 mA | 7 | |
| Leakage current high-side switch, switcher 2 | ILKSW2 | 5 | µA | VEN2 = 0 V, VSW2 = 0, VIN2 = 5.5 V | 7 | ||
| Minimum ON time, switcher 2 | tON2MIN | 60 | 80 | 95 | ns | Measured at SW2 pin | 7 |
| Non-overlap time, switcher 2 | tNOVLP | 10 | ns | 7 | |||
| Current limit threshold, switcher 1 normal mode | ILIM1 | 3.9 | 4.4 | 4.9 | A | VSTBYB = 5 V | 8 |
| Current limit threshold, switcher 1 low-Iq mode | ILIM1,stby | 0.15 | 0.2 | 0.25 | A | VSTBYB = 0 V | 8 |
| Current limit threshold, switcher 2 | ILIM2 | 2.6 | 2.9 | 3.2 | A | 8 | |
| Lowest foldback frequency, switcher 1 | fSW1AF | 450 | 550 | 650 | kHz | VOUT = 0 V, 4.5 V < VBAT < 18 V | 8 |
| Lowest foldback frequency, high VIN | fSW1AFHV | 225 | 275 | 325 | kHz | VOUT = 0 V, 20 V < VBAT < 28 V | 8 |
| Reset output low level | VRESL | 0.4 | V | IRSTBx = 2 mA | 8 | ||
| Output voltage VDRV1, VDRV2 | VDRV1, VDRV2 | 3.1 | 3.3 | 3.5 | V | 8 | |
| RMOD pin voltage | VRMOD | 0.54 | 0.6 | 0.66 | V | RMOD = 10 k | 8 |
| ERRB output low level | VERRBL | 0.4 | V | IERRB = 1 mA | 8 | ||
| Thermal shutdown activation temperature | TSD | 150 | 190 | C | Not tested in production; guaranteed by design | 9 | |
| Thermal shutdown hysteresis | THYS | 5 | 20 | C | Not tested in production; guaranteed by design | 9 |
CAD (KiCad official)
- Symbol:
NCV97310MW33AR2G - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
ncv97310mw33ar2g-etched.step/ncv97310mw33ar2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncv97310mw33ar2g.step/ncv97310mw33ar2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (22 pp, sha256
9420d87c78af0491, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# NCV97310MW33AR2G
**onsemi** · Power Management Specialized - PMIC · QFN-32-EP(5x5)
NCV97310MW33AR2G from onsemi, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Battery input voltage that must be tied to pin 29 VINL, with an input filter capacitor placed close to the pin. |
| 2 | EN | input | High-voltage TTL-compatible master enable; grounding this input stops all outputs and reduces Iq to a minimum (shutdown mode). |
| 3 | STBYB | input | High-voltage TTL-compatible mode select; grounding this input activates the low-Iq standby mode for switcher 1. |
| 4 | RDEPTH | passive | Sets the modulation depth (% of FSW) for spread spectrum with a resistor to GND. |
| 5 | RMOD | passive | Sets the modulation frequency for spread spectrum with a resistor to GND. |
| 6 | RSTB1 | output | Reset output with adjustable delay that goes low when the output is out of regulation; in Low-Iq LDO mode it needs a pull-up to a permanent external supply such as VOUT1. |
| 7 | COMP1 | passive | Output of the error amplifier for switcher 1. |
| 8 | ROSC | passive | Provides frequency adjustment for the switching oscillator. |
| 9 | ERRB | output | Error flag combining temperature, input voltage and output voltage sensing. |
| 10 | EN2 | input | TTL-compatible low-voltage input; grounding this input stops switcher 2. |
| 11 | RSTB2 | output | Reset output with adjustable delay that goes low when the switcher 2 output is out of regulation. |
| 12 | GND1 | power_in | Ground reference for the IC, which the exposed pad must also be connected to. |
| 13 | RSTB3 | output | Reset output with adjustable delay that goes low when the switcher 3 output is out of regulation. |
| 14 | FB3 | input | Output voltage sensing input for switcher 3 that provides output voltage adjustability. |
| 15 | EN3 | input | TTL-compatible low-voltage input; grounding this input stops switcher 3. |
| 16 | BST3 | passive | Bootstrap input that supplies high-side N-channel drive voltage above VIN3 for optimum RDS(on) and efficiency. |
| 17 | GND3 | power_in | Ground connection for the source of the switcher 3 low-side switch. |
| 18 | SW3L | passive | Drain of the switcher 3 low-side switch that connects to the output inductor and must be tied to SW3H. |
| 19 | SW3H | passive | Source of the switcher 3 high-side switch that connects to the output inductor and must be tied to SW3L. |
| 20 | VDRV2 | passive | Internal supply for driving the low-voltage internal switches, which needs a noise-filter capacitor. |
| 21 | VIN3 | power_in | Low input voltage for switcher 3 that must be tied to pin 22 VIN2 and pin 28 VOUT, with an input filter capacitor close to the pin. |
| 22 | VIN2 | power_in | Low input voltage for switcher 2 that must be tied to pin 21 VIN3 and pin 28 VOUT, with an input filter capacitor close to the pin. |
| 23 | SW2 | passive | Switching node of the switcher 2 regulator that connects to the output inductor. |
| 24 | GND2 | power_in | Ground connection for the source of the switcher 2 low-side switch. |
| 25 | BST2 | passive | Bootstrap input that supplies high-side N-channel drive voltage above VIN2 for optimum RDS(on) and efficiency. |
| 26 | NC | unconnected | No-connect pin that must be left floating. |
| 27 | FB2 | input | Output voltage sensing input for switcher 2 that provides output voltage adjustability. |
| 28 | VOUT | power_out | Output voltage sensing pin that delivers the output current in low-Iq mode and must be tied to VIN2 and VIN3. |
| 29 | VINL | power_in | Battery input voltage that must be tied to pin 1 VBAT, with an input filter capacitor close to the pin. |
| 30 | BST1 | passive | Bootstrap input that supplies N-channel power switch drive voltage above VBAT for optimum Rdson and efficiency. |
| 31 | VDRV1 | passive | Internal supply for driving the low-voltage internal switch, which needs a noise-filter capacitor. |
| 32 | SW1 | passive | Switching node of the regulator that connects the output inductor and the freewheeling diode cathode. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | QFN-32-EP(5x5) |
| Category | Power Management ICs |
| Pins | 33 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage from battery (VBAT, VINL) | VBAT, VINL | -0.3 | | 45 | V | | 4 |
| Max voltage VBAT to SW1 | | | | 45 | V | | 4 |
| Min/Max voltage SW1 | SW1 | -0.7 | | 40 | V | | 4 |
| Min voltage SW1, SW2, SW3 | SW1, SW2, SW3 | -3 | | | V | 20 ns | 4 |
| Min/Max voltage BST1, STBYB, EN | BST1, STBYB, EN | -0.3 | | 40 | V | | 4 |
| Min/Max voltage VIN2, VIN3, BST2, BST3, SW2, SW3H, SW3L, VOUT | VIN2, VIN3, BST2, BST3, SW2, SW3H, SW3L, VOUT | -0.3 | | 12 | V | | 4 |
| Min/Max voltage on RSTB2, RSTB3, EN2, EN3, FB2, FB3 | RSTB2, RSTB3, EN2, EN3, FB2, FB3 | -0.3 | | 6 | V | | 4 |
| Min/Max voltage on RSTB1, ERRB | RSTB1, ERRB | -0.3 | | 3.6 | V | | 4 |
| Max voltage BST1 to SW1, BST2 to SW2, BST3 to SWx | | | | 3.6 | V | | 4 |
| Min/Max voltage VDRV1, VDRV2, COMP1, ROSC, RMOD, RDEPTH | VDRV1, VDRV2, COMP1, ROSC, RMOD, RDEPTH | -0.3 | | 3.6 | V | | 4 |
| Thermal resistance junction to ambient, 5x5 QFN | RJA | | | 25 | C/W | Mounted on 1 sq. in. of 4-layer PCB, 1 oz. copper | 4 |
| Storage temperature range | | -55 | | 150 | C | | 4 |
| Operating junction temperature range | TJ | -40 | | 150 | C | | 4 |
| ESD withstand voltage, human body model | VESD | | | 2 | kV | Human body model | 4 |
| ESD withstand voltage, machine model | VESD | | | 200 | V | Machine model | 4 |
| VIN range | VIN | 4.5 | | 36 | V | | 4 |
| Ambient temperature range | TA | -40 | | 125 | C | | 4 |
| Quiescent current, shutdown | IqSD | 8 | | 12 | µA | VBAT = VINL = 13.2 V, TJ=25C, VEN = 0 V | 6 |
| Quiescent current, standby | IqEN | 25 | | 35 | µA | VBAT = VINL = 13.2 V, TJ=25C, VEN = 3 V, VSTBYB = VEN2 = VEN3 = 0 V | 6 |
| VBAT UVLO start threshold | VUV1ST | 4.45 | | 4.85 | V | VBAT rising | 6 |
| VBAT UVLO stop threshold | VUV1SP | 3.7 | | 4.1 | V | VBAT falling | 6 |
| Enable logic low | VENLO, VEN2LO, VEN3LO, VSTBYBLO | | | 0.8 | V | Voltage input needed to guarantee logic low | 6 |
| Enable logic high | VENHI, VEN2HI, VEN3HI, VSTBYBHI | 2 | | | V | Voltage input needed to guarantee logic high | 6 |
| Enable pin input current | IEN | 0.125 | | 1 | µA | VEN = 5 V | 6 |
| STBYB pin input current | ISTBYB | 0.5 | | 2 | µA | VSTBYB = 5 V | 6 |
| Enable pin input current, EN2/EN3 | IEN2, IEN3 | 30 | 50 | 70 | µA | VEN2 = VEN3 = 5 V | 6 |
| Switcher 1 start-up time | tSTBYB | 60 | | 200 | µs | STBYB high to switcher 1 ready | 6 |
| Switcher 1 output voltage | VOUT | 3.23 | 3.3 | 3.37 | V | | 6 |
| VOUT line regulation in low-Iq mode | VLine1 | 5 | | 25 | mV | IOUT = 50 mA, VSTBYB = 0 V, 6 V < VINL = VBAT < 28 V | 6 |
| VOUT load regulation in low-Iq mode | VLoad1 | 10 | | 35 | mV | VINL = VBAT = 13.2 V, VSTBYB = 0 V, 1 mA < IOUT < 150 mA | 6 |
| Voltage drop-out in low-Iq mode | VDROP1 | | | 500 | mV | IOUT = 150 mA, VSTBYB = 0 V | 6 |
| Switchers 2 and 3 FB pin voltage during regulation | VFB2R, VFB3R | 1.179 | 1.2 | 1.221 | V | OUTx connected to FBx through a 10 k resistor | 6 |
| Error amplifier transconductance, switcher 1 | gm | 0.6 | 1 | 1.4 | mmho | VCOMP = 1.1 V, 4.5 V < VBAT < 18 V | 6 |
| Error amplifier transconductance, high VBAT | gm(HV) | 0.35 | 0.55 | 0.75 | mmho | VCOMP = 1.1 V, 20 V < VBAT < 28 V | 6 |
| COMP source current limit | ISOURCE | 50 | 75 | 100 | µA | VOUT = 4.0 V, VCOMP = 1.1 V, 4.5 V < VBAT < 18 V | 6 |
| Minimum COMP voltage | VCMPMIN | 0.15 | | 0.3 | V | VOUT = 6.0 V | 6 |
| Switching frequency, switcher 1 | fSW1 | 1.8 | 2 | 2.2 | MHz | 4.5 < VBAT < 18 V, ROSC = open | 7 |
| Switching frequency, switcher 1, high VBAT | fSW1(HV) | 0.9 | 1 | 1.1 | MHz | 20 V < VBAT < 28 V, ROSC = open | 7 |
| Switching frequency, ROSC | fROSC | 2.3 | 2.5 | 2.8 | MHz | ROSC = 12.5 k | 7 |
| ROSC reference voltage | VROSC | 0.9 | 1 | 1.1 | V | ROSC = 25 k | 7 |
| Frequency foldback threshold, rising | VFL1U | 18.4 | | 20 | V | VBAT rising | 7 |
| Frequency foldback threshold, falling | VFL1D | 18 | | 19.8 | V | VBAT falling | 7 |
| Ramp slope, switcher 1 | Sramp1 | 1.8 | | 3.4 | A/s | 4.5 < VBAT < 18 V | 7 |
| ON resistance, switcher 1 power switch | RDS1ON | 185 | | 360 | mΩ | VBST1 = VSW1 + 3.0 V, ISW1 = 500 mA | 7 |
| Leakage current VBAT to SW1 | ILKSW1 | | | 10 | µA | VEN = 0 V, VSW1 = 0, VBAT = 18 V | 7 |
| Minimum ON time, switcher 1 | tON1MIN | 45 | | 70 | ns | Measured at SW1 pin | 7 |
| Minimum OFF time, switcher 1 | tOFF1MIN | 30 | 50 | 70 | ns | Measured at SW1 pin | 7 |
| High-side ON resistance, switcher 2 | RHS2ON | 165 | 300 | | mΩ | VBST2 = VSW2 + 3.0 V, ISW2 = 500 mA | 7 |
| Low-side ON resistance, switcher 2 | RLS2ON | 130 | 230 | | mΩ | ISW2 = 500 mA | 7 |
| Leakage current high-side switch, switcher 2 | ILKSW2 | | | 5 | µA | VEN2 = 0 V, VSW2 = 0, VIN2 = 5.5 V | 7 |
| Minimum ON time, switcher 2 | tON2MIN | 60 | 80 | 95 | ns | Measured at SW2 pin | 7 |
| Non-overlap time, switcher 2 | tNOVLP | | 10 | | ns | | 7 |
| Current limit threshold, switcher 1 normal mode | ILIM1 | 3.9 | 4.4 | 4.9 | A | VSTBYB = 5 V | 8 |
| Current limit threshold, switcher 1 low-Iq mode | ILIM1,stby | 0.15 | 0.2 | 0.25 | A | VSTBYB = 0 V | 8 |
| Current limit threshold, switcher 2 | ILIM2 | 2.6 | 2.9 | 3.2 | A | | 8 |
| Lowest foldback frequency, switcher 1 | fSW1AF | 450 | 550 | 650 | kHz | VOUT = 0 V, 4.5 V < VBAT < 18 V | 8 |
| Lowest foldback frequency, high VIN | fSW1AFHV | 225 | 275 | 325 | kHz | VOUT = 0 V, 20 V < VBAT < 28 V | 8 |
| Reset output low level | VRESL | | | 0.4 | V | IRSTBx = 2 mA | 8 |
| Output voltage VDRV1, VDRV2 | VDRV1, VDRV2 | 3.1 | 3.3 | 3.5 | V | | 8 |
| RMOD pin voltage | VRMOD | 0.54 | 0.6 | 0.66 | V | RMOD = 10 k | 8 |
| ERRB output low level | VERRBL | | | 0.4 | V | IERRB = 1 mA | 8 |
| Thermal shutdown activation temperature | TSD | 150 | | 190 | C | Not tested in production; guaranteed by design | 9 |
| Thermal shutdown hysteresis | THYS | 5 | | 20 | C | Not tested in production; guaranteed by design | 9 |
## CAD (KiCad official)
- Symbol: `NCV97310MW33AR2G`
- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`
- 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files: `ncv97310mw33ar2g-etched.step` / `ncv97310mw33ar2g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ncv97310mw33ar2g.step` / `ncv97310mw33ar2g.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/ncv97310mw33ar2-d.pdf) (22 pp, sha256 `9420d87c78af0491`, retrieved 2026-11-21)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ncv97310mw33ar2g-datasheet.pdf)