main
Ray
ncv7341d21r2g: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero
ce5242c
NCV7341D21R2G
onsemi · CAN Controllers · SOIC-14
NCV7341D21R2G from onsemi, in a SOIC-14. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TxD | input | Transmit data input from the CAN controller. Low level drives a dominant state on the bus; has an internal pull-up current so the pin defaults high (recessive) if disconnected. A TxD dominant time-out disables the transmitter after tdom(TxD) = 300-1000 us to prevent bus lockup. |
| 2 | GND | power_in | Ground reference for the device. All voltages in the datasheet are referenced to GND (Pin 2). |
| 3 | VCC | power_in | Supply voltage for the core circuitry and the CAN transceiver output stage. Operating range 4.75 V to 5.25 V; absolute max +7 V. |
| 4 | RxD | output | Receive data output to the CAN controller. Dominant bus state produces a low output; recessive bus state produces a high output. Output levels are referenced to VIO for controller interface flexibility. |
| 5 | VIO | power_in | Supply voltage for the digital interface to the CAN controller / microcontroller, allowing interfacing to controllers with 3 V or 5 V I/O. Operating range 2.8 V to 5.25 V; absolute max +7 V. |
| 6 | EN | input | Enable / mode-control input (together with STB selects Normal, Receive-only, Standby, Go-to-Sleep, or Sleep modes). Has an internal pull-down current so pin defaults low if disconnected. Levels referenced to VIO. |
| 7 | INH | output | High-voltage inhibit output for controlling external voltage regulators. Pulled high (near VBAT, with typ 200 mV drop at 180 uA) in Normal/Receive-only/Standby/Go-to-Sleep modes; floats in Sleep mode to switch off the external regulators. Rated up to VBAT+0.3 V. |
| 8 | ERR | output | Active-low digital output that indicates internal flag conditions (power-up, wake-up, failure, and bus failure on the D20 version). Uses negative logic - pulled low when a signaled flag is set. Levels referenced to VIO. |
| 9 | WAKE | input | Local wake-up input. A stable High-to-Low or Low-to-High transition longer than tWAKE (5-50 us) is detected as a local wake-up event in Standby/Go-to-Sleep/Sleep modes. Internal current source (~5 uA pull-up or pull-down following the pin state). Rated up to 58 V; connect to GND or VBAT if unused. |
| 10 | VBAT | power_in | Battery supply connection (12 V or 24 V systems). Operating range 5 V to 50 V (6 V to 50 V guaranteed in Sleep mode); absolute max 58 V. Supplies the low-power wake circuitry and the INH output. |
| 11 | VSPLIT | output | Common-mode stabilization output providing VCC/2 (0.3VCC to 0.7VCC) in Normal and Receive-only modes for use with split termination to reduce EME. High-impedance (floating) in Standby and Sleep modes. Protected against short-circuit to battery/ground; rated -58 V to +58 V DC and +/-300 V transient. |
| 12 | CANL | bidirectional | Low-level CAN bus line (driven low in dominant state, typ 1.4 V). Differential pair with CANH; rated -58 V to +58 V DC and +/-300 V transient (ISO 7637). Short-circuit protected and thermally protected. |
| 13 | CANH | bidirectional | High-level CAN bus line (driven high in dominant state, typ 3.6 V). Differential pair with CANL; rated -58 V to +58 V DC and +/-300 V transient (ISO 7637). Short-circuit protected and thermally protected. |
| 14 | STB | input | Active-low stand-by mode control input (together with EN selects operating mode). Has an internal pull-down current so pin defaults low if disconnected. Levels referenced to VIO. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-14 |
| Category | Interface |
| Pins | 14 |
Ordering variants
NCV7341D21R2GD21GNCV7341D21R2GNCV7341D21R2GD20GNCV7341D21R2GD20R2G
CAD (KiCad official)
- Symbol:
NCV7341D21R2G - Footprint:
Package_SO:SOIC-14_3.9x8.7mm_P1.27mm - 3D model: SOIC-14 (KiCad packages3D, STEP)
- 3D model files:
ncv7341d21r2g-etched.step/ncv7341d21r2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncv7341d21r2g.step/ncv7341d21r2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (None pp, sha256
59d663c1f4054c72, retrieved 2026-08-17, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# NCV7341D21R2G
**onsemi** · CAN Controllers · SOIC-14
NCV7341D21R2G from onsemi, in a SOIC-14. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TxD | input | Transmit data input from the CAN controller. Low level drives a dominant state on the bus; has an internal pull-up current so the pin defaults high (recessive) if disconnected. A TxD dominant time-out disables the transmitter after tdom(TxD) = 300-1000 us to prevent bus lockup. |
| 2 | GND | power_in | Ground reference for the device. All voltages in the datasheet are referenced to GND (Pin 2). |
| 3 | VCC | power_in | Supply voltage for the core circuitry and the CAN transceiver output stage. Operating range 4.75 V to 5.25 V; absolute max +7 V. |
| 4 | RxD | output | Receive data output to the CAN controller. Dominant bus state produces a low output; recessive bus state produces a high output. Output levels are referenced to VIO for controller interface flexibility. |
| 5 | VIO | power_in | Supply voltage for the digital interface to the CAN controller / microcontroller, allowing interfacing to controllers with 3 V or 5 V I/O. Operating range 2.8 V to 5.25 V; absolute max +7 V. |
| 6 | EN | input | Enable / mode-control input (together with STB selects Normal, Receive-only, Standby, Go-to-Sleep, or Sleep modes). Has an internal pull-down current so pin defaults low if disconnected. Levels referenced to VIO. |
| 7 | INH | output | High-voltage inhibit output for controlling external voltage regulators. Pulled high (near VBAT, with typ 200 mV drop at 180 uA) in Normal/Receive-only/Standby/Go-to-Sleep modes; floats in Sleep mode to switch off the external regulators. Rated up to VBAT+0.3 V. |
| 8 | ERR | output | Active-low digital output that indicates internal flag conditions (power-up, wake-up, failure, and bus failure on the D20 version). Uses negative logic - pulled low when a signaled flag is set. Levels referenced to VIO. |
| 9 | WAKE | input | Local wake-up input. A stable High-to-Low or Low-to-High transition longer than tWAKE (5-50 us) is detected as a local wake-up event in Standby/Go-to-Sleep/Sleep modes. Internal current source (~5 uA pull-up or pull-down following the pin state). Rated up to 58 V; connect to GND or VBAT if unused. |
| 10 | VBAT | power_in | Battery supply connection (12 V or 24 V systems). Operating range 5 V to 50 V (6 V to 50 V guaranteed in Sleep mode); absolute max 58 V. Supplies the low-power wake circuitry and the INH output. |
| 11 | VSPLIT | output | Common-mode stabilization output providing VCC/2 (0.3*VCC to 0.7*VCC) in Normal and Receive-only modes for use with split termination to reduce EME. High-impedance (floating) in Standby and Sleep modes. Protected against short-circuit to battery/ground; rated -58 V to +58 V DC and +/-300 V transient. |
| 12 | CANL | bidirectional | Low-level CAN bus line (driven low in dominant state, typ 1.4 V). Differential pair with CANH; rated -58 V to +58 V DC and +/-300 V transient (ISO 7637). Short-circuit protected and thermally protected. |
| 13 | CANH | bidirectional | High-level CAN bus line (driven high in dominant state, typ 3.6 V). Differential pair with CANL; rated -58 V to +58 V DC and +/-300 V transient (ISO 7637). Short-circuit protected and thermally protected. |
| 14 | STB | input | Active-low stand-by mode control input (together with EN selects operating mode). Has an internal pull-down current so pin defaults low if disconnected. Levels referenced to VIO. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-14 |
| Category | Interface |
| Pins | 14 |
## Ordering variants
- `NCV7341D21R2GD21G`
- `NCV7341D21R2G`
- `NCV7341D21R2GD20G`
- `NCV7341D21R2GD20R2G`
## CAD (KiCad official)
- Symbol: `NCV7341D21R2G`
- Footprint: `Package_SO:SOIC-14_3.9x8.7mm_P1.27mm`
- 3D model: SOIC-14 (KiCad packages3D, STEP)
- 3D model files: `ncv7341d21r2g-etched.step` / `ncv7341d21r2g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ncv7341d21r2g.step` / `ncv7341d21r2g.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/ncv7341d21r2-d.pdf) (None pp, sha256 `59d663c1f4054c72`, retrieved 2026-08-17, tier: manufacturer)
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ncv7341d21r2g-datasheet.pdf)