main
Ray
Publish 0.1.0
08abaec
NCV360SNT1G
onsemi · Pre-ordered transistors · TSOP-5
NCV360SNT1G from onsemi, in a TSOP-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Input voltage pin connected to VBUS; a 1 µF low ESR ceramic capacitor or larger must be connected between this pin and GND (absolute max 21 V, operating range 1.2 V to 20 V). |
| 2 | GND | power_in | Ground. |
| 3 | EN | input | Enable pin; tying it high (VIH ≥ 1.2 V) puts the device in shutdown and disconnects OUT from IN, connect to GND or an I/O pin for normal operation, and it has no impact on fault detection. |
| 4 | FLAG | output | Open-drain fault indication pin that goes low when input voltage exceeds the OVLO threshold, requiring an external pull-up resistor to VCC. |
| 5 | OUT | output | Output voltage pin that is disconnected from VBUS when input is above the OVLO threshold or below the UVLO threshold; a 1 µF capacitor must be connected to this pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | TSOP-5 |
| Category | Transistors |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Undervoltage Lockout Threshold | UVLO | 2.85 | 3 | 3.15 | V | Vin falls below UVLO threshold | 5 |
| Undervoltage Lockout Hysteresis | UVLOhyst | 50 | 70 | 90 | mV | MU/SN | 5 |
| Overvoltage Lockout Threshold | OVLO | 5.43 | 5.675 | 5.9 | V | Vin rises above OVLO threshold, MU/SN | 5 |
| Overvoltage Lockout Hysteresis | OVLOhyst | 50 | 100 | 125 | mV | 5 | |
| Input Voltage Range | Vin | 1.2 | 20 | V | 5 | ||
| Vin versus Vout Dropout | Vdrop | 105 | 200 | mV | Vin = 5 V, I charge = 500 mA | 5 | |
| Supply Quiescent Current | Idd | 24 | 35 | µA | No Load, Vin = 5.25 V | 5 | |
| OVLO Supply Current | Iddovlo | 50 | 85 | µA | Vin = 7 V MU/SN | 5 | |
| Output Off State Current | Istd | 26 | 37 | µA | Vin = 5.25 V, EN = 1.2 V | 5 | |
| FLAG Output Low Voltage | Volflag | 400 | mV | Vin > OVLO, Sink 1 mA on FLAG pin | 5 | ||
| FLAG Leakage Current | FLAGleak | 5 | nA | FLAG level = 5 V | 5 | ||
| EN Voltage High | Vih | 1.2 | V | Vin from 3.3 V to 5.25 V | 5 | ||
| EN Voltage Low | Vil | 0.4 | V | Vin from 3.3 V to 5.25 V | 5 | ||
| EN Leakage Current | ENleak | 170 | nA | EN = 5.5 V or GND | 5 | ||
| Start Up Delay | ton | 4 | 15 | ms | From Vin: (0 to (OVLO − 300 mV) < Vin < OVLO) to Vout = 0.8xVin, Rise time<4s | 5 | |
| FLAG going up Delay | tstart | 3 | ms | From Vin > UVLO to FLAG = 1.2 V | 5 | ||
| Output Turn Off Time | toff | 0.8 | 1.5 | µs | From Vin > OVLO to Vout ≤ 0.3 V, Vin increasing at 1V/µs, no output capacitor | 5 | |
| Alert Delay | tstop | 1 | 2 | µs | From Vin > OVLO to FLAG ≤ 0.4 V, Vin increasing at 1V/µs | 5 | |
| Disable Time | tdis | 2 | µs | From EN 0.4 to 1.2V to Vout ≤ 0.3V, Vin = 4.75 V. No output capacitor. | 5 | ||
| Thermal Shutdown Temperature | Tsd | 150 | °C | 5 | |||
| Thermal Shutdown Hysteresis | Tsdhyst | 30 | °C | 5 | |||
| Maximum Voltage (IN to GND) | Vmaxin | 21 | V | 4 | |||
| Minimum Voltage (IN to GND) | Vminin | -0.3 | V | 4 | |||
| Maximum Voltage (All others to GND) | Vmax | 7 | V | 4 | |||
| Minimum Voltage (All others to GND) | Vmin | -0.3 | V | 4 | |||
| Maximum Current from Vin to Vout (PMOS) | Imax | 600 | mA | With minimum PCB area | 4 | ||
| Thermal Resistance, Junction-to-Air | RθJA | 305 | °C/W | TSOP-5 | 4 | ||
| Operating Ambient Temperature Range | TA | -40 | 85 | °C | 4 | ||
| Storage Temperature Range | Tstg | -65 | 150 | °C | 4 | ||
| Junction Operating Temperature | TJ | 150 | °C | 4 | |||
| ESD Withstand Voltage HBM | Vesd | 2000 | V | Human Body Model, Model = 2 | 4 | ||
| ESD Withstand Voltage MM | Vesd | 200 | V | Machine Model, Model = B | 4 |
CAD (KiCad official)
- Symbol:
NCV360SNT1G - Footprint:
Package_SO:TSOP-5_1.65x3.05mm_P0.95mm - 3D model: TSOP-5 (KiCad packages3D, STEP)
- 3D model files:
ncv360snt1g-etched.step/ncv360snt1g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncv360snt1g.step/ncv360snt1g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (14 pp, sha256
975be70a5e967aa2, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# NCV360SNT1G
**onsemi** · Pre-ordered transistors · TSOP-5
NCV360SNT1G from onsemi, in a TSOP-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Input voltage pin connected to VBUS; a 1 µF low ESR ceramic capacitor or larger must be connected between this pin and GND (absolute max 21 V, operating range 1.2 V to 20 V). |
| 2 | GND | power_in | Ground. |
| 3 | EN | input | Enable pin; tying it high (VIH ≥ 1.2 V) puts the device in shutdown and disconnects OUT from IN, connect to GND or an I/O pin for normal operation, and it has no impact on fault detection. |
| 4 | FLAG | output | Open-drain fault indication pin that goes low when input voltage exceeds the OVLO threshold, requiring an external pull-up resistor to VCC. |
| 5 | OUT | output | Output voltage pin that is disconnected from VBUS when input is above the OVLO threshold or below the UVLO threshold; a 1 µF capacitor must be connected to this pin. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | TSOP-5 |
| Category | Transistors |
| Pins | 5 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Undervoltage Lockout Threshold | UVLO | 2.85 | 3 | 3.15 | V | Vin falls below UVLO threshold | 5 |
| Undervoltage Lockout Hysteresis | UVLOhyst | 50 | 70 | 90 | mV | MU/SN | 5 |
| Overvoltage Lockout Threshold | OVLO | 5.43 | 5.675 | 5.9 | V | Vin rises above OVLO threshold, MU/SN | 5 |
| Overvoltage Lockout Hysteresis | OVLOhyst | 50 | 100 | 125 | mV | | 5 |
| Input Voltage Range | Vin | 1.2 | | 20 | V | | 5 |
| Vin versus Vout Dropout | Vdrop | | 105 | 200 | mV | Vin = 5 V, I charge = 500 mA | 5 |
| Supply Quiescent Current | Idd | | 24 | 35 | µA | No Load, Vin = 5.25 V | 5 |
| OVLO Supply Current | Iddovlo | | 50 | 85 | µA | Vin = 7 V MU/SN | 5 |
| Output Off State Current | Istd | | 26 | 37 | µA | Vin = 5.25 V, EN = 1.2 V | 5 |
| FLAG Output Low Voltage | Volflag | | | 400 | mV | Vin > OVLO, Sink 1 mA on FLAG pin | 5 |
| FLAG Leakage Current | FLAGleak | | | 5 | nA | FLAG level = 5 V | 5 |
| EN Voltage High | Vih | 1.2 | | | V | Vin from 3.3 V to 5.25 V | 5 |
| EN Voltage Low | Vil | | | 0.4 | V | Vin from 3.3 V to 5.25 V | 5 |
| EN Leakage Current | ENleak | | | 170 | nA | EN = 5.5 V or GND | 5 |
| Start Up Delay | ton | | 4 | 15 | ms | From Vin: (0 to (OVLO − 300 mV) < Vin < OVLO) to Vout = 0.8xVin, Rise time<4s | 5 |
| FLAG going up Delay | tstart | | 3 | | ms | From Vin > UVLO to FLAG = 1.2 V | 5 |
| Output Turn Off Time | toff | | 0.8 | 1.5 | µs | From Vin > OVLO to Vout ≤ 0.3 V, Vin increasing at 1V/µs, no output capacitor | 5 |
| Alert Delay | tstop | | 1 | 2 | µs | From Vin > OVLO to FLAG ≤ 0.4 V, Vin increasing at 1V/µs | 5 |
| Disable Time | tdis | | | 2 | µs | From EN 0.4 to 1.2V to Vout ≤ 0.3V, Vin = 4.75 V. No output capacitor. | 5 |
| Thermal Shutdown Temperature | Tsd | | 150 | | °C | | 5 |
| Thermal Shutdown Hysteresis | Tsdhyst | | 30 | | °C | | 5 |
| Maximum Voltage (IN to GND) | Vmaxin | | | 21 | V | | 4 |
| Minimum Voltage (IN to GND) | Vminin | -0.3 | | | V | | 4 |
| Maximum Voltage (All others to GND) | Vmax | | | 7 | V | | 4 |
| Minimum Voltage (All others to GND) | Vmin | -0.3 | | | V | | 4 |
| Maximum Current from Vin to Vout (PMOS) | Imax | | | 600 | mA | With minimum PCB area | 4 |
| Thermal Resistance, Junction-to-Air | RθJA | | 305 | | °C/W | TSOP-5 | 4 |
| Operating Ambient Temperature Range | TA | -40 | | 85 | °C | | 4 |
| Storage Temperature Range | Tstg | -65 | | 150 | °C | | 4 |
| Junction Operating Temperature | TJ | | | 150 | °C | | 4 |
| ESD Withstand Voltage HBM | Vesd | | | 2000 | V | Human Body Model, Model = 2 | 4 |
| ESD Withstand Voltage MM | Vesd | | | 200 | V | Machine Model, Model = B | 4 |
## CAD (KiCad official)
- Symbol: `NCV360SNT1G`
- Footprint: `Package_SO:TSOP-5_1.65x3.05mm_P0.95mm`
- 3D model: TSOP-5 (KiCad packages3D, STEP)
- 3D model files: `ncv360snt1g-etched.step` / `ncv360snt1g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ncv360snt1g.step` / `ncv360snt1g.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/ncv360snt1-d.pdf) (14 pp, sha256 `975be70a5e967aa2`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ncv360snt1g-datasheet.pdf)