3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownNCS2252SN2T1G
onsemi · Comparators · TSOP-5
NCS2252SN2T1G from onsemi, in a TSOP-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | output | Open-drain comparator output on the NCS2252, which requires an external pull-up resistor that may connect to voltages below VDD or up to VDD + 0.3 V. |
| 2 | VSS | power_in | Negative supply pin; connect to ground or negative rail, with a bypass capacitor of at least 0.1 μF close to the pin if not connected to ground. |
| 3 | IN+ | input | Non-inverting input with rail-to-rail common mode range from VSS − 0.2 V to VDD + 0.2 V. |
| 4 | IN− | input | Inverting input with rail-to-rail common mode range from VSS − 0.2 V to VDD + 0.2 V. |
| 5 | VDD | power_in | Positive supply pin (1.8 V to 5.5 V); connect to positive rail with a bypass capacitor of at least 0.1 μF as close as possible to the pin. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | TSOP-5 |
| Category | Amplifiers |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Range | VS | 0 | 6 | V | VDD - VSS | 3 | |
| Input Voltage Range | VIN | -0.3 | 0.3 | V | VSS - 0.3 to VDD + 0.3 (relative to rails) | 3 | |
| Maximum Junction Temperature | TJ(max) | 150 | °C | 3 | |||
| Storage Temperature Range | Tstg | -65 | 150 | °C | 3 | ||
| ESD Human Body Model | HBM | 2000 | V | 3 | |||
| ESD Machine Model | MM | 50 | V | 3 | |||
| Latch-up Current | ILU | 100 | mA | 3 | |||
| Junction-to-Ambient Thermal Resistance | θJA | 150 | °C/W | TSOP-5 (SOT23-5), single layer board | 3 | ||
| Power Supply Voltage | VS | 1.8 | 5.5 | V | 3 | ||
| Ambient Temperature | TA | -40 | 125 | °C | 3 | ||
| Quiescent Supply Current | IDD | 150 | 200 | μA | VDD = 5 V, No load; 250 over -40 to 125°C | 4 | |
| Quiescent Supply Current (full temp) | IDD | 250 | μA | VDD = 5 V, No load, TA = -40°C to 125°C | 4 | ||
| Power Supply Rejection Ratio | PSRR | 62.5 | 88 | dB | VDD = 5 V | 4 | |
| Input Offset Voltage | VOS | 0.5 | 6 | mV | VDD = 5 V | 4 | |
| Input Bias Current | IIB | 20 | 1000 | pA | VDD = 5 V | 4 | |
| Input Offset Current | IOS | 20 | 1000 | pA | VDD = 5 V | 4 | |
| Common Mode Rejection Ratio | CMRR | 59 | 81 | dB | VDD = 5 V | 4 | |
| Output Voltage Low | VOL | 0.09 | 0.3 | V | VDD = 5 V, IOUT = 4 mA; VSS + value | 4 | |
| Output Leakage Current | ILEAK | 1 | nA | NCS2252, VS = 5.5 V | 4 | ||
| Propagation Delay tpHL | tpHL | 50 | 64 | ns | NCS2252, VDD = 5 V, VOD = 100 mV | 4 | |
| Propagation Delay tpHL | tpHL | 60 | ns | NCS2252, VDD = 5 V, VOD = 50 mV | 4 | ||
| Propagation Delay tpHL | tpHL | 90 | ns | NCS2252, VDD = 5 V, VOD = 20 mV | 4 | ||
| Quiescent Supply Current | IDD | 145 | 200 | μA | VDD = 1.8 V, No load | 5 | |
| Quiescent Supply Current (full temp) | IDD | 250 | μA | VDD = 1.8 V, No load, TA = -40°C to 125°C | 5 | ||
| Power Supply Rejection Ratio | PSRR | 62.5 | 82 | dB | VDD = 1.8 V | 5 | |
| Input Offset Voltage | VOS | 0.5 | 6 | mV | VDD = 1.8 V | 5 | |
| Input Bias Current | IIB | 20 | 1000 | pA | VDD = 1.8 V | 5 | |
| Input Offset Current | IOS | 20 | 1000 | pA | VDD = 1.8 V | 5 | |
| Common Mode Rejection Ratio | CMRR | 55 | 76 | dB | VDD = 1.8 V | 5 | |
| Output Voltage Low | VOL | 0.12 | 0.3 | V | VDD = 1.8 V, IOUT = 4 mA; VSS + value | 5 | |
| Output Leakage Current | ILEAK | 1 | nA | NCS2252, VS = 5.5 V | 5 | ||
| Propagation Delay tpHL | tpHL | 56 | 68 | ns | NCS2252, VDD = 1.8 V, VOD = 100 mV | 5 | |
| Propagation Delay tpHL | tpHL | 71 | ns | NCS2252, VDD = 1.8 V, VOD = 50 mV | 5 | ||
| Propagation Delay tpHL | tpHL | 106 | ns | NCS2252, VDD = 1.8 V, VOD = 20 mV | 5 |
CAD (KiCad official)
- Symbol:
NCS2252SN2T1G - Footprint:
Package_SO:TSOP-5_1.65x3.05mm_P0.95mm - 3D model: TSOP-5 (KiCad packages3D, STEP)
- 3D model files:
ncs2252sn2t1g-etched.step/ncs2252sn2t1g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncs2252sn2t1g.step/ncs2252sn2t1g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet, copy hosted by DigiKey (12 pp, sha256
5600ff2f6674ceda, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).