main
Ray Publish 0.1.0 4527450
{
  "slug": "ncp730bmt330tbg",
  "version": "0.1.0",
  "type": "component",
  "description": "onsemi Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, WDFN-6 (2x2mm, P0.65mm, CASE 511BR, EP 1.6x1.0mm). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "power management (pmic)",
    "ncp730bmt330tbg",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "ncp730bmt330tbg.kicad_sym",
    "ncp730bmt330tbg.kicad_mod",
    "ncp730bmt330tbg.glb",
    "ncp730bmt330tbg.step",
    "ncp730bmt330tbg.lbr",
    "docs/hero.png",
    "docs/ncp730bmt330tbg-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "ncp730bmt330tbg-hero.glb",
    "ncp730bmt330tbg-hero.overlay.json"
  ],
  "component": {
    "mpn": "NCP730BMT330TBG",
    "land_source": "datasheet",
    "land_note": "onsemi NCP730/D p.32, CASE 511BR WDFN6 2x2 0.65P (98AON55829E, Issue C), RECOMMENDED MOUNTING FOOTPRINT: 6X 0.40 pad width, 6X 0.45 pad length, 0.65 pitch, 2.30 outer span across both pad rows -> pad centres at +/-(2.30-0.45)/2 = +/-0.925 mm from the body centre line; exposed pad 1.72 (along the pad rows) x 1.12, centred; gap EP-to-pad 0.14. The footprint drawing is a TOP view: its '1' label sits at the lower-left pad, matching the TOP VIEW pin 1 reference (lower-left hatched corner), while the BOTTOM VIEW shows pin 1 upper-left (mirrored about the horizontal axis), so pins run counter-clockwise from the top: 1-2-3 along the pin-1 row, 4-5-6 back along the other. Page 1 PIN ASSIGNMENTS WDFN6 (Top Views) confirms 1-3 down the left, 6-4 down the right ('NC/ADJ 2 ... EP ... 5 NC/PG'). Rotated 90 deg (no mirror) for KiCad pin 1 top-left: pins 1-3 at x=-0.925, y=-0.65/0/+0.65; pins 4-6 at x=+0.925, y=+0.65/0/-0.65; pads 0.45 (x) x 0.40 (y). Exposed pad (pin table 'EP / EPAD, connect to GND') numbered 7, 1.12 (x) x 1.72 (y). Body from the dimension table: D 2.00, E 2.00 nom, A 0.70/0.75/0.80; D2 1.60, E2 1.00 nom; b 0.30, L 0.30, e 0.65 BSC. Ordering table p.29: NCP730BMT330TBG = WDFN6 2x2 (marking MF).",
    "manufacturer": "onsemi",
    "package": "WDFN-6 (2x2mm, P0.65mm, CASE 511BR, EP 1.6x1.0mm)",
    "pin_count": 7,
    "category": "Power Management (PMIC)",
    "subcategory": "Voltage Regulators - Linear, Low Drop Out (LDO) Regulators",
    "datasheet": "https://www.onsemi.com/pdf/datasheet/ncp730bmt330tb-d.pdf",
    "parts": {
      "symbol": "ncp730bmt330tbg.kicad_sym",
      "footprint": "ncp730bmt330tbg.kicad_mod",
      "model_3d": "ncp730bmt330tbg-hero.glb",
      "model_3d_plain": "ncp730bmt330tbg.glb",
      "model_3d_step": "ncp730bmt330tbg-etched.step",
      "model_3d_step_plain": "ncp730bmt330tbg.step",
      "lbr": "ncp730bmt330tbg.lbr"
    },
    "distributor_links": {
      "lcsc": "C892821",
      "digikey": "488-NCP730BMT330TBGTR-ND",
      "mouser": "863-NCP730BMT330TBG"
    },
    "distributor_check": {
      "checked_at": "2026-11-19T05:58:58Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": "488-NCP730BMT330TBGTR-ND",
        "status": "found"
      },
      "mouser": {
        "pn": "863-NCP730BMT330TBG",
        "status": "found"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "OUT",
        "type": "power_out",
        "description": "Output pin of the LDO regulator."
      },
      {
        "number": "2",
        "name": "NC/ADJ",
        "type": "unconnected",
        "description": "For this fixed-output (FIX) version the pin is not internally connected and can be tied to the ground plane to improve thermal dissipation."
      },
      {
        "number": "3",
        "name": "GND",
        "type": "power_in",
        "description": "Ground pin."
      },
      {
        "number": "4",
        "name": "EN",
        "type": "input",
        "description": "Enable input (high enabled, low disabled); if connected to IN or left unconnected the device is enabled, and no pull-up resistor is required."
      },
      {
        "number": "5",
        "name": "NC/PG",
        "type": "output",
        "description": "Power good output for the version B device: high level indicates output power OK and low level indicates fail; if not used it can be left unconnected or shorted to GND."
      },
      {
        "number": "6",
        "name": "IN",
        "type": "power_in",
        "description": "Power supply input pin, recommended input range 2.7 V to 38 V."
      },
      {
        "number": "7",
        "name": "EP",
        "type": "passive",
        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "exposed pad 7 added from the footprint",
          "dropped thermal pad ['EP'] absent from footprint"
        ],
        "pages_sent": 13,
        "cost_usd": 0.0293,
        "at": "2026-11-19T05:58:50"
      },
      "datasheet": {
        "url": "https://www.onsemi.com/pdf/datasheet/ncp730bmt330tb-d.pdf",
        "pages": 33,
        "sha256": "6e6fad810dc3e948",
        "source_tier": "mfr",
        "citation": "onsemi datasheet"
      },
      "cad": "Adom_Gen derived land; symbol and 3D generated",
      "pins": {
        "total": 7,
        "described": 7,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "ncp730bmt330tbg.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          2.02,
          2.0,
          0.75
        ],
        "zmin_mm": 0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "3a2ff9d5899d34b60a6342e077f0b64cd03986d34e86c8549c2c3dbea2525a20",
        "checked": "2026-11-19",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "ncp730bmt330tbg-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          2.02,
          2.0,
          0.75
        ],
        "zmin_mm": 0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "342197011c2c9939daf2be7bcfac6acbff60760cbe0b16ae11e6f4b759918f0e",
        "checked": "2026-11-19",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}