main
Ray
Publish 0.1.0
4527450
NCP730BMT330TBG
onsemi · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · WDFN-6 (2x2mm, P0.65mm, CASE 511BR, EP 1.6x1.0mm)
NCP730BMT330TBG from onsemi, in a WDFN-6 (2x2mm, P0.65mm, CASE 511BR, EP 1.6x1.0mm). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Output pin of the LDO regulator. |
| 2 | NC/ADJ | unconnected | For this fixed-output (FIX) version the pin is not internally connected and can be tied to the ground plane to improve thermal dissipation. |
| 3 | GND | power_in | Ground pin. |
| 4 | EN | input | Enable input (high enabled, low disabled); if connected to IN or left unconnected the device is enabled, and no pull-up resistor is required. |
| 5 | NC/PG | output | Power good output for the version B device: high level indicates output power OK and low level indicates fail; if not used it can be left unconnected or shorted to GND. |
| 6 | IN | power_in | Power supply input pin, recommended input range 2.7 V to 38 V. |
| 7 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | WDFN-6 (2x2mm, P0.65mm, CASE 511BR, EP 1.6x1.0mm) |
| Category | Power Management (PMIC) |
| Pins | 7 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Recommended Input Voltage | VIN | 2.7 | 38 | V | 4 | ||
| Output Voltage Accuracy | VOUT | -1 | 1 | % | TJ = −40 °C to +85 °C | 4 | |
| Output Voltage Accuracy | VOUT | -1 | 2 | % | TJ = −40 °C to +125 °C | 4 | |
| ADJ Input Current | IADJ | -0.1 | 0.01 | 0.1 | A | VADJ = 1.2 V | 4 |
| Line Regulation | VO(VI) | 0.2 | %VOUT | VIN = VOUT-NOM + 1 V to 38 V and VIN ≥ 2.7 V | 4 | ||
| Load Regulation | VO(IO) | 0.4 | %VOUT | IOUT = 0.1 mA to 150 mA | 4 | ||
| Quiescent Current (version B) | IQ | 1.8 | 3 | A | VIN = VOUT-NOM + 1 V to 38 V, IOUT = 0 mA | 4 | |
| Ground Current | IGND | 325 | 450 | A | IOUT = 150 mA | 4 | |
| Shutdown Current | ISHDN | 0.35 | 1.5 | A | VEN = 0 V, IOUT = 0 mA, VIN = 38 V | 4 | |
| Output Current Limit | IOLIM | 200 | 280 | 450 | mA | VOUT = VOUT-NOM − 100 mV | 5 |
| Short Circuit Current | IOSC | 200 | 280 | 450 | mA | VOUT = 0 V | 5 |
| Dropout Voltage | VDO | 290 | 480 | mV | IOUT = 150 mA | 5 | |
| EN Threshold | VEN-TH | 0.7 | 0.9 | 1.05 | V | VEN rising | 5 |
| EN Hysteresis | VEN-HY | 0.01 | 0.1 | 0.2 | V | VEN falling | 5 |
| EN Internal Pull-up Current | IEN-PU | 0.01 | 0.3 | 1 | A | VEN = 1 V, VIN = 5.5 V | 5 |
| EN Input Leakage Current | IEN-LK | -1 | 0.05 | 1 | A | VEN = 30 V, VIN = 30 V | 5 |
| Start-up time | tSTART | 100 | 250 | 500 | s | VOUT-NOM ≤ 3.3 V | 5 |
| Internal UVLO Threshold | VIUL-TH | 1.6 | 1.95 | 2.6 | V | Ramp VIN up until output is turned on | 5 |
| Internal UVLO Hysteresis | VIUL-HY | 0.05 | 0.2 | 0.3 | V | Ramp VIN down until output is turned off | 5 |
| PG Threshold | VPG-TH | 90 | 93 | 96 | % | VOUT falling | 5 |
| PG Hysteresis | VPG-HY | 0.1 | 2 | 4 | % | VOUT rising | 5 |
| PG Deglitch Time | tPG-DG | 75 | 160 | 270 | s | 5 | |
| PG Delay Time | tPG-DLY | 120 | 320 | 600 | s | 5 | |
| PG Output Low Level Voltage | VPG-OL | 0.2 | 0.4 | V | IPG = 1 mA | 5 | |
| PG Output Leakage Current | IPG-LK | 0.01 | 1 | A | VPG = 30 V | 5 | |
| VIN Voltage (absolute maximum) | VIN | -0.3 | 40 | V | 4 | ||
| VOUT Voltage (FIX, VOUT-NOM ≤ 5.0 V) | VOUT | -0.3 | V | max is the lower of (VIN + 0.3) or 6.0 V | 4 | ||
| EN Voltage | VEN | -0.3 | V | max is VIN + 0.3 V | 4 | ||
| PG Voltage | VPG | -0.3 | V | max is VIN + 0.3 V | 4 | ||
| PG Current | IPG | 3 | mA | 4 | |||
| Maximum Junction Temperature | TJ(MAX) | 150 | °C | 4 | |||
| Storage Temperature | TSTG | -55 | 150 | °C | 4 | ||
| ESD Capability, Human Body Model | ESDHBM | 2000 | V | 4 | |||
| ESD Capability, Charged Device Model | ESDCDM | 1000 | V | 4 | |||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | Stated in the electrical characteristics table header | 4 | |
| Thermal Resistance, Junction-to-Air (WDFN6 2x2) | RthJA | 67 | °C/W | JEDEC board 1S2P, no airflow | 4 | ||
| Thermal Resistance, Junction-to-Case top (WDFN6 2x2) | RthJCt | 89 | °C/W | 4 | |||
| Thermal Resistance, Junction-to-Case bottom (WDFN6 2x2) | RthJCb | 11 | °C/W | 4 | |||
| Thermal Resistance, Junction-to-Board top (WDFN6 2x2) | RthJBt | 44 | °C/W | 4 | |||
| Thermal Characterization Parameter, Junction-to-Case top (WDFN6 2x2) | PsiJCt | 4.6 | °C/W | 4 | |||
| Thermal Characterization Parameter, Junction-to-Board (WDFN6 2x2) | PsiJB | 44 | °C/W | 4 |
CAD (Adom-generated)
- Symbol:
NCP730BMT330TBG - Footprint:
Adom_Gen:onsemi_NCP730_279921 - 3D model: generated to fit the land (STEP)
- 3D model files:
ncp730bmt330tbg-etched.step/ncp730bmt330tbg-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp730bmt330tbg.step/ncp730bmt330tbg.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (33 pp, sha256
6e6fad810dc3e948, retrieved 2026-11-19) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land. Land: onsemi NCP730/D p.32, CASE 511BR WDFN6 2x2 0.65P (98AON55829E, Issue C), RECOMMENDED MOUNTING FOOTPRINT: 6X 0.40 pad width, 6X 0.45 pad length, 0.65 pitch, 2.30 outer span across both pad rows -> pad centres at +/-(2.30-0.45)/2 = +/-0.925 mm from the body centre line; exposed pad 1.72 (along the pad rows) x 1.12, centred; gap EP-to-pad 0.14. The footprint drawing is a TOP view: its '1' label sits at the lower-left pad, matching the TOP VIEW pin 1 reference (lower-left hatched corner), while the BOTTOM VIEW shows pin 1 upper-left (mirrored about the horizontal axis), so pins run counter-clockwise from the top: 1-2-3 along the pin-1 row, 4-5-6 back along the other. Page 1 PIN ASSIGNMENTS WDFN6 (Top Views) confirms 1-3 down the left, 6-4 down the right ('NC/ADJ 2 ... EP ... 5 NC/PG'). Rotated 90 deg (no mirror) for KiCad pin 1 top-left: pins 1-3 at x=-0.925, y=-0.65/0/+0.65; pins 4-6 at x=+0.925, y=+0.65/0/-0.65; pads 0.45 (x) x 0.40 (y). Exposed pad (pin table 'EP / EPAD, connect to GND') numbered 7, 1.12 (x) x 1.72 (y). Body from the dimension table: D 2.00, E 2.00 nom, A 0.70/0.75/0.80; D2 1.60, E2 1.00 nom; b 0.30, L 0.30, e 0.65 BSC. Ordering table p.29: NCP730BMT330TBG = WDFN6 2x2 (marking MF).
# NCP730BMT330TBG
**onsemi** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · WDFN-6 (2x2mm, P0.65mm, CASE 511BR, EP 1.6x1.0mm)
NCP730BMT330TBG from onsemi, in a WDFN-6 (2x2mm, P0.65mm, CASE 511BR, EP 1.6x1.0mm). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Output pin of the LDO regulator. |
| 2 | NC/ADJ | unconnected | For this fixed-output (FIX) version the pin is not internally connected and can be tied to the ground plane to improve thermal dissipation. |
| 3 | GND | power_in | Ground pin. |
| 4 | EN | input | Enable input (high enabled, low disabled); if connected to IN or left unconnected the device is enabled, and no pull-up resistor is required. |
| 5 | NC/PG | output | Power good output for the version B device: high level indicates output power OK and low level indicates fail; if not used it can be left unconnected or shorted to GND. |
| 6 | IN | power_in | Power supply input pin, recommended input range 2.7 V to 38 V. |
| 7 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | WDFN-6 (2x2mm, P0.65mm, CASE 511BR, EP 1.6x1.0mm) |
| Category | Power Management (PMIC) |
| Pins | 7 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Recommended Input Voltage | VIN | 2.7 | | 38 | V | | 4 |
| Output Voltage Accuracy | VOUT | -1 | | 1 | % | TJ = −40 °C to +85 °C | 4 |
| Output Voltage Accuracy | VOUT | -1 | | 2 | % | TJ = −40 °C to +125 °C | 4 |
| ADJ Input Current | IADJ | -0.1 | 0.01 | 0.1 | A | VADJ = 1.2 V | 4 |
| Line Regulation | VO(VI) | | | 0.2 | %VOUT | VIN = VOUT-NOM + 1 V to 38 V and VIN ≥ 2.7 V | 4 |
| Load Regulation | VO(IO) | | | 0.4 | %VOUT | IOUT = 0.1 mA to 150 mA | 4 |
| Quiescent Current (version B) | IQ | | 1.8 | 3 | A | VIN = VOUT-NOM + 1 V to 38 V, IOUT = 0 mA | 4 |
| Ground Current | IGND | | 325 | 450 | A | IOUT = 150 mA | 4 |
| Shutdown Current | ISHDN | | 0.35 | 1.5 | A | VEN = 0 V, IOUT = 0 mA, VIN = 38 V | 4 |
| Output Current Limit | IOLIM | 200 | 280 | 450 | mA | VOUT = VOUT-NOM − 100 mV | 5 |
| Short Circuit Current | IOSC | 200 | 280 | 450 | mA | VOUT = 0 V | 5 |
| Dropout Voltage | VDO | | 290 | 480 | mV | IOUT = 150 mA | 5 |
| EN Threshold | VEN-TH | 0.7 | 0.9 | 1.05 | V | VEN rising | 5 |
| EN Hysteresis | VEN-HY | 0.01 | 0.1 | 0.2 | V | VEN falling | 5 |
| EN Internal Pull-up Current | IEN-PU | 0.01 | 0.3 | 1 | A | VEN = 1 V, VIN = 5.5 V | 5 |
| EN Input Leakage Current | IEN-LK | -1 | 0.05 | 1 | A | VEN = 30 V, VIN = 30 V | 5 |
| Start-up time | tSTART | 100 | 250 | 500 | s | VOUT-NOM ≤ 3.3 V | 5 |
| Internal UVLO Threshold | VIUL-TH | 1.6 | 1.95 | 2.6 | V | Ramp VIN up until output is turned on | 5 |
| Internal UVLO Hysteresis | VIUL-HY | 0.05 | 0.2 | 0.3 | V | Ramp VIN down until output is turned off | 5 |
| PG Threshold | VPG-TH | 90 | 93 | 96 | % | VOUT falling | 5 |
| PG Hysteresis | VPG-HY | 0.1 | 2 | 4 | % | VOUT rising | 5 |
| PG Deglitch Time | tPG-DG | 75 | 160 | 270 | s | | 5 |
| PG Delay Time | tPG-DLY | 120 | 320 | 600 | s | | 5 |
| PG Output Low Level Voltage | VPG-OL | | 0.2 | 0.4 | V | IPG = 1 mA | 5 |
| PG Output Leakage Current | IPG-LK | | 0.01 | 1 | A | VPG = 30 V | 5 |
| VIN Voltage (absolute maximum) | VIN | -0.3 | | 40 | V | | 4 |
| VOUT Voltage (FIX, VOUT-NOM ≤ 5.0 V) | VOUT | -0.3 | | | V | max is the lower of (VIN + 0.3) or 6.0 V | 4 |
| EN Voltage | VEN | -0.3 | | | V | max is VIN + 0.3 V | 4 |
| PG Voltage | VPG | -0.3 | | | V | max is VIN + 0.3 V | 4 |
| PG Current | IPG | | | 3 | mA | | 4 |
| Maximum Junction Temperature | TJ(MAX) | | | 150 | °C | | 4 |
| Storage Temperature | TSTG | -55 | | 150 | °C | | 4 |
| ESD Capability, Human Body Model | ESDHBM | | | 2000 | V | | 4 |
| ESD Capability, Charged Device Model | ESDCDM | | | 1000 | V | | 4 |
| Operating Junction Temperature Range | TJ | -40 | | 125 | °C | Stated in the electrical characteristics table header | 4 |
| Thermal Resistance, Junction-to-Air (WDFN6 2x2) | RthJA | | 67 | | °C/W | JEDEC board 1S2P, no airflow | 4 |
| Thermal Resistance, Junction-to-Case top (WDFN6 2x2) | RthJCt | | 89 | | °C/W | | 4 |
| Thermal Resistance, Junction-to-Case bottom (WDFN6 2x2) | RthJCb | | 11 | | °C/W | | 4 |
| Thermal Resistance, Junction-to-Board top (WDFN6 2x2) | RthJBt | | 44 | | °C/W | | 4 |
| Thermal Characterization Parameter, Junction-to-Case top (WDFN6 2x2) | PsiJCt | | 4.6 | | °C/W | | 4 |
| Thermal Characterization Parameter, Junction-to-Board (WDFN6 2x2) | PsiJB | | 44 | | °C/W | | 4 |
## CAD (Adom-generated)
- Symbol: `NCP730BMT330TBG`
- Footprint: `Adom_Gen:onsemi_NCP730_279921`
- 3D model: generated to fit the land (STEP)
- 3D model files: `ncp730bmt330tbg-etched.step` / `ncp730bmt330tbg-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ncp730bmt330tbg.step` / `ncp730bmt330tbg.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/ncp730bmt330tb-d.pdf) (33 pp, sha256 `6e6fad810dc3e948`, retrieved 2026-11-19)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land. Land: onsemi NCP730/D p.32, CASE 511BR WDFN6 2x2 0.65P (98AON55829E, Issue C), RECOMMENDED MOUNTING FOOTPRINT: 6X 0.40 pad width, 6X 0.45 pad length, 0.65 pitch, 2.30 outer span across both pad rows -> pad centres at +/-(2.30-0.45)/2 = +/-0.925 mm from the body centre line; exposed pad 1.72 (along the pad rows) x 1.12, centred; gap EP-to-pad 0.14. The footprint drawing is a TOP view: its '1' label sits at the lower-left pad, matching the TOP VIEW pin 1 reference (lower-left hatched corner), while the BOTTOM VIEW shows pin 1 upper-left (mirrored about the horizontal axis), so pins run counter-clockwise from the top: 1-2-3 along the pin-1 row, 4-5-6 back along the other. Page 1 PIN ASSIGNMENTS WDFN6 (Top Views) confirms 1-3 down the left, 6-4 down the right ('NC/ADJ 2 ... EP ... 5 NC/PG'). Rotated 90 deg (no mirror) for KiCad pin 1 top-left: pins 1-3 at x=-0.925, y=-0.65/0/+0.65; pins 4-6 at x=+0.925, y=+0.65/0/-0.65; pads 0.45 (x) x 0.40 (y). Exposed pad (pin table 'EP / EPAD, connect to GND') numbered 7, 1.12 (x) x 1.72 (y). Body from the dimension table: D 2.00, E 2.00 nom, A 0.70/0.75/0.80; D2 1.60, E2 1.00 nom; b 0.30, L 0.30, e 0.65 BSC. Ordering table p.29: NCP730BMT330TBG = WDFN6 2x2 (marking MF).
[Datasheet PDF](docs/ncp730bmt330tbg-datasheet.pdf)